Стиральная машина brandt wd1004w инструкция по применению

Detailed instructions for use are in the User’s Guide.

[. . . ] With innovation and performance, we designed it to be always easy to use. In the BRANDT product range, you will also find a wide choice of ovens, microwaves, cooking hobs, ventilation hoods, cookers, dishwashers, driers, fridges and freezers, that you can coordinate with your new BRANDT washing machine. Visit our website www. brandt. com where you will find all of our products, as well as useful and complementary information.

BRANDT

·SAFETY ADVICE
Important :
This machine is only for domestic use and is designed to wash, rinse and spin machine-washable textiles. We refuse to accept any liability and the guarantee if you do not observe these recommendations since this could result in damage to equipment or physical injury. [. . . ] — Install your machine in an area where it could be subject to water splashes. If you cannot avoid doing this, please take every precaution to avoid blocking air circulation at the bottom of the machine in order to ensure that the internal components are well ventilated.

·Dispensing the detergent
The amount of detergent to be used depends on the hardness of the water, the extent to which your washing is soiled and the amount of washing to be washed. Warning: in most cases, the detergent manufacturer’s recommendations apply to the drum filled to the maximum. Adjust the dosage correctly to the weight of the washing you have placed in the machine. These recommendations will help you to avoid using too much detergent, which causes foam to be produced. In any case, the»Start/Pause» button cannot cancel a programme.

Important :
Before starting your machine, check that the power cable is plugged in and the water tap is open. Also ensure that the drum doors are closed correctly and the machine’s lid is shut. During the «End of Cycle» phase, any action on one of the controls (the selectors or the buttons) returns you to «Programming» mode. As a safety measure, when the cycle is over, we recommend that you unplug the power cable and turn off the water tap.

Spin speed setting
(depending on the model)

2

3

4

Delayed start setting
(depending on the model)

Options

·Programming a washing cycle:
— Turn the selector 1 to choose the most suitable programme and washing temperature for

Indicator lights and position of the selectors

NB: Turning the selector to any position other than «Off» provides power to the machine.

«Wash» light flashing (If you have selected rinse only or spin only, it is the «Rinse/Spin» light that flashes

— Using the selector 2 (depending on the model of the machine), choose: Selector 2 on — Either a suitable spin speed for your type of washing. The spin speed is automatically restricted to 800 rpm in the «Woollens» programme and — Position «800» for example to 600 rpm in the «Delicates» and «Hand wash» programmes. — Position «100» The cycle will finish with a gentle spin at 100 rpm. — You can alter the length of a delayed start ( ) throughout the waiting period before the cycle effectively starts. NB : — During this period, selecting a new time cancels out the previous selection. — If you want to cancel the delayed start completely during this period, set the selector 3 to the «0ff» position and then briefly press the «Start/Pause» button 5 . — You can only activate the «Prewash» and «Easy Ironing» or «Intensive» options during a delayed start’s waiting period.

·Easy ironing (depending on the model)
This avoids the washing creasing and makes it easier to iron.

·Intensive (depending on the model)
This function enables you to handle so-called «difficult» stubborn stains

·Rinse plus
«Especially for sensitive and allergic skin»: adds an extra rinse to the washing cycle.

·Delayed start (depending on the model)
You can delay the start of your programme by 1, 3, 6, 9, 12, 15 or 19 hours so that you can benefit from cheap rate electricity or to have the cycle finish at a desired time. To do this, use the selector 3 to choose the time you want the cycle to start and press «Start/Pause» 5 . NB: — Even if you forget to press the «Start/Pause» button 5 after selecting this option, your choice will still be accepted after a few seconds. — The three cycle progress lights (Wash , Rinse/Spin and «Stop») flash in succession from left to right during the whole of the waiting period before the cycle effectively starts.

·When the cycle is over:
When the «Stop» light is permanently lit, you can programme a new cycle without having to reset the selector 1 to the «Off» position. For this, all you have to do is turn one of the selectors or press one of the buttons. The machine is then ready to be reprogrammed.

·Full drum stop
This function enables you to remove the washing from your machine before the spin phase or to delay this phase with you washing remaining in water to prevent creasing. NB : When the machine is stopped with the tub full of water, the «Rinse/Spin» cycle progress light flashes. There are then two possible cases, depending on the type of machine: — «Full drum stop» selected via a rotary selector: — If you want to drain after spinning, use the selector 2 to choose a suitable spin speed for your type of washing. [. . . ] To do this: — Press the bosses on each side of the box simultaneously to extract it from its housing(Diagram D24). — Remove the siphons from the rear of the box and separate the box from its front cover (Diagram D25) — Rinse everything under the tap (taking care to empty any excess water remaining inside the box). — Refit all the box’ components, ensuring that the box section itself is properly clipped into the cover and then re-insert the complete assembly into its location under the machine’s lid.

·CLEANING THE PUMP FILTER (Option 2)
if your machine dopes not have the component A shown in Diagram D16, you must proceed as follows to clean your pump filter: — Turn the drum to position the closed doors facing downwards: this will reveal a plastic component (Diagram D20) — If your machine is fitted with one, remove the screw — On certain types of machines, the component has a clip. In this case, release the component by pressing on this clip while sliding the component gently to the right — Then, in all cases, turn the drum again, open the doors and remove the component by sliding it in the direction of the arrow (Diagram D21) — Turn the drum slightly towards the front of the machine, with the doors open (Diagram D22). [. . . ]