Still r70 45 мануал - Большая энциклопедия инструкций и руководств

Contents
Table of Contents
Bookmarks

Quick Links

Original instructions

Diesel trucks

With SCR (Selective Catalytic Reduction)

RX70-60

RX70-70

RX70-80

RX70-80/900

7341 7342 7343 7344

57348011800 EN — 11/2018

Related Manuals for Still RX70 Series

Summary of Contents for Still RX70 Series

Page 1
Original instructions Diesel trucks With SCR (Selective Catalytic Reduction) RX70-60 RX70-70 RX70-80 RX70-80/900 7341 7342 7343 7344 57348011800 EN — 11/2018…
Page 3
• Information on transport, initial commis- sioning and storage of industrial trucks Internet address and QR code The information can be accessed at any time by pasting the address https://m.still.de/vdma in a web browser or by scanning the QR code. 57348011800 EN — 11/2018…
Page 5: Table Of Contents

Table of contents Foreword Your truck …………2 Description of the truck .
Page 6
Table of contents Changes to the overhead guard and roof loads ……33 Warning regarding non-original parts .
Page 7
Table of contents Operation Testing and activities before daily use ……..72 Visual inspections .
Page 8
Table of contents Actuating the drive direction switch, ﬁngertip version ……130 Actuating the drive direction switch, mini-console version ….. . 131 Starting to drive .
Page 9
STILL SafetyLight (variant) ……..
Page 10
Table of contents Closing the cab door ……….238 Opening the side windows .
Page 11
Table of contents Transporting the truck ……….300 Transport .
Page 12
Table of contents Topping up the cooling ﬂuid and checking the coolant concentration ….343 Cleaning the radiator and checking for leaks ……. . 346 Draining water from the fuel ﬁlter .
Page 13: Foreword

Foreword…
Page 14: Your Truck

Foreword Your truck Your truck Description of the truck General Counterbalanced trucks in the RX70-60/70/80 series with a load capacity of up to 8.0 t are equipped with an internal combustion/electric drive. The internal combustion/electric drive combines the advantages of an internal combustion engine with the precise control of an electric drive.
Page 15
Foreword Your truck brake ensures that the truck remains securely in place when parked. Steering The truck is equipped with a swing axle and has kickback-free hydraulic rear-wheel steer- ing. Stability is guaranteed when cornering thanks to speed limitation based on the steer- ing angle.
Page 16
Foreword Your truck sumption by up to 10% without impairing per- formance. The truck’s cutting-edge exhaust regeneration system also keeps it well within the thresholds of the currently applicable IIIB EU standard. This is achieved using selective catalytic reduction combined with a diesel par- ticulate ﬁlter.
Page 17: General

Foreword Your truck General The truck described in these operating instruc- tions corresponds to the applicable standards and safety regulations. If the truck is to be operated on public roads, it must conform to the existing national regula- tions for the country in which it is being used. The driving permit must be obtained from the appropriate ofﬁce.
Page 18: Use In The Event Of Frost

Foreword Your truck The applicable European emission require- ments (97/68/EC) state that new engines must have an SCR system. Use in the event of frost AdBlue freezes at temperatures of -11°C and below. If the AdBlue tank and the lines freeze, they will be heated automatically during startup and operation.
Page 19: Ec Declaration Of Conformity In Accordance With Machinery Directive

Foreword Your truck EC declaration of conformity in accordance with Machinery Directive Declaration STILL GmbH Berzeliusstraße 10 D-22113 Hamburg Germany We declare that the according to these operating instructions Industrial truck according to these operating instructions Model conforms to the latest version of the Machinery Directive 2006/42/EC.
Page 20: Accessories

Foreword Your truck Accessories • Key for key switch (two pieces) • Key for cab (variant) • Hexagon socket wrench for emergency lowering 57348011800 EN — 11/2018…
Page 21
Foreword Your truck 57348011800 EN — 11/2018…
Page 22: Labelling Points

Foreword Your truck Labelling points Overview of the front of the truck and the left-hand side of the truck DANGER DANGER STILL GmbH Hamburg Regelmäßige Prüfung (FEM 4.004) nach nationalen Vorschriften basierend auf den EG-Richtlinien: 2009/104/EG, 99/92/EG Nächste Prüfung 10 bar DANGER Die Prüfplakette ersetzt nicht das Prüfprotokoll…
Page 23
Foreword Your truck Decal information: Caution/Read the op- Warning sign: Do not stand underneath the erating instructions/Fasten seat belt/Apply fork/Do not stand on the fork parking brake when leaving the truck/Pas- Decal information: StVZO (German Road sengers are not allowed/Do not jump off if Trafﬁc Licensing Regulations) information the truck is tipping over/Lean in the opposite (variant)
Page 24
Foreword Your truck Overview of the rear of the truck and the right-hand side of the truck DANGER DANGER 10 bar 57348011800 EN — 11/2018…
Page 25: Nameplate

Foreword Your truck Decal information: Parking brake released Decal information: 12-V socket Decal information: Parking brake applied Decal information: Diesel fuel Decal information: Lifting gear attachment Decal information: Tyre ﬁlling pressure point (variant) Manufacturer’s label text Decal information: To unlock, turn 90° to the Decal information: Caution / Read the right/to lock, turn 90°…
Page 26: Production Number

Foreword Using the truck Production number xx xxxx x xxxxx NOTE The production number is used to identify the truck. It can be found on the nameplate and must be referred to in all technical questions. The production number contains the following coded information: (1) Production location (2) Model…
Page 27: Proper Use During Towing

Foreword Using the truck The truck may only be used for its proper purpose as set out and described in these operating instructions. If the truck is to be used for purposes other than those speciﬁed in the operating instruc- tions, the approval of the manufacturer and, if applicable, the relevant regulatory authorities must be obtained beforehand to prevent haz-…
Page 28: Place Of Use

Foreword Using the truck The truck may not be operated in areas where there is a risk of ﬁre, explosion or corrosion, or in areas that are particularly dusty. Stacking or unstacking is not permissible on inclined surfaces or ramps. Place of use The truck can be used outdoors.
Page 29: Using Working Platforms

Foreword Using the truck NOTE Please note the deﬁnition of «operating com- pany» in the sense of responsible persons! DANGER Risk to health from exhaust gases! Exhaust gases from internal combustion engines are harmful to your health. In particular, the soot particles contained in the diesel exhaust gas can cause cancer.
Page 30: Information About The Documentation

Foreword Information about the documentation Information about the documentation Documentation scope • Original operating instructions • Original operating instructions for attach- ments (variant) • Spare parts list • Depending on the truck equipment, «UPA» operating instructions may also be provided NOTE Refer to the additional information in the section entitled «Rules for the operating…
Page 31: Supplementary Documentation

Foreword Information about the documentation The personnel responsible for operating and maintaining the equipment must be familiar with these operating instructions. The operating company must ensure that all users have received, read and understood these operating instructions. Safely store the complete documentation and pass on to the subsequent operating company when transferring or selling the truck.
Page 32: Issue Date And Topicality Of The Operating Instructions

The issue date of these operating instructions can be found on the title page. STILL is constantly engaged in the further development of trucks. These operating instructions are subject to change, and any claims based on the information and/or illustrations contained in them cannot be asserted.
Page 33: List Of Abbreviations

Foreword Information about the documentation NOTE For technical requirements that require special attention. ENVIRONMENT NOTE To prevent environmental damage. List of abbreviations NOTE This list of abbreviations applies to all types of operating instructions. Not all of the abbre- viations that are listed here will necessarily appear in these operating instructions.
Page 34
Foreword Information about the documentation Abbrevi- Meaning Explanation ation German authority for monitoring/issuing regulations for worker protection, environ- Gewerbeaufsichtsamt mental protection, and consumer protec- tion Transfer of data packets in wireless GPRS General Packet Radio Service networks ID no. ID number International Organization for Standard- International standardisation organisation ization…
Page 35: Definition Of Directions

Foreword Information about the documentation Deﬁnition of directions The directions «forwards» (1), «backwards» (3), «right» (2) and «left» (4) refer to the installation position of the parts as seen from the driver’s compartment; the load is to the front. 6210_001-031 Schematic views View of functions and operations This documentation explains the (usually…
Page 36
Foreword Information about the documentation View of the display operating unit NOTE Views of operating statuses and values in the display of the display operating unit are examples and partly dependent on the truck equipment. As a result, the displays shown of the actual operating statuses and values can vary.
Page 37: Environmental Considerations

Foreword Environmental considerations Environmental considerations Packaging During delivery of the truck, certain parts are packaged to provide protection during transport. This packaging must be removed completely prior to initial start-up. ENVIRONMENT NOTE The packaging material must be disposed of properly after delivery of the truck. Disposal of components and batteries The truck is composed of different materials.
Page 38
Foreword Environmental considerations 57348011800 EN — 11/2018…
Page 39: Safety

Safety…
Page 40: Definition Of Responsible Persons

Safety Deﬁnition of responsible persons Deﬁnition of responsible persons Operating company The operating company is the natural or legal person or group who operates the truck or on whose authority the truck is used. The operating company must ensure that the truck is only used for its proper purpose and in compliance with the safety regulations set out in these operating instructions.
Page 41: Drivers

Safety Deﬁnition of responsible persons regarding the industrial truck to be tested and the risk being assessed Drivers This truck may only be driven by suitable per- sons who are at least 18 years of age, have been trained in driving, have demonstrated their skills in driving and handling loads to the operating company or an authorised rep- resentative, and have been speciﬁcally in-…
Page 42
Safety Deﬁnition of responsible persons DANGER The use of drugs, alcohol or medications that affect reactions impair the ability to drive the truck! Individuals under the inﬂuence of the aforementio- ned substances are not permitted to perform work of any kind on or with the truck. Prohibition of use by unauthorised persons The driver is responsible for the truck during…
Page 43: Basic Principles For Safe Operation

Safety Basic principles for safe operation Basic principles for safe operation Insurance cover on company premises In many cases, company premises are restricted public trafﬁc areas. NOTE The business liability insurance should be reviewed to ensure that, in the event of any damage caused in restricted public trafﬁc areas, there is insurance cover for the truck in respect of third parties.
Page 44
DANGER Risk of injury if the truck tips over! Even if an approved restraint system is in use, there is still a residual risk that the driver could be injured if the truck tips over. The risk of injury can…
Page 45: Changes To The Overhead Guard And Roof Loads

Original parts, attachments and accessories are specially designed for this truck. We speciﬁcally draw your attention to the fact that parts, attachments and accessories supplied by other companies have not been tested and approved by STILL. 57348011800 EN — 11/2018…
Page 46: Damage, Defects And Misuse Of Safety Systems

Safety Basic principles for safe operation CAUTION Installation and/or use of such products may there- fore have a negative impact on the design features of the truck and thus impair active and/or passive driving safety. We recommend that you obtain approval from the manufacturer and, if necessary, from the relevant regulatory authorities before installing such parts.
Page 47
Safety Basic principles for safe operation The following factors can lead to a loss of stability and are therefore prohibited: • Different tyres on the same axle, e.g. pneumatic tyres and superelastic tyres • Tyres not approved by the manufacturer •…
Page 48: Medical Equipment

Safety Basic principles for safe operation Medical equipment WARNING Electromagnetic interference may occur on medical devices! Only use equipment that is sufﬁciently protected against electromagnetic interference. Medical equipment, such as pacemakers or hearing aids, may not work properly when the truck is in operation.
Page 49: Length Of The Fork Arms

Safety Basic principles for safe operation Length of the fork arms DANGER Risk of accident due to the incorrect selection of fork arms! – The fork arms must match the depth of the load. If the fork arms are too short, the load may fall off the arms after it has been picked up.
Page 50: Residual Risk

Safety Residual risk Residual risk Residual dangers, residual risks Despite careful working and compliance with standards and regulations, the occurrence of other risks when using the truck cannot be entirely excluded. The truck and all other system components comply with current safety requirements. Nevertheless, even when the truck is used for its proper purpose and all instructions are followed, some residual risk cannot be…
Page 51: Special Risks Associated With Using The Truck And Attachments

Safety Residual risk The manufacturer is not held responsible for accidents involving the truck caused by the failure of the operating company to comply with these regulations either intentionally or carelessly. Stability The stability of the truck has been tested to the latest technological standards and is guaran- teed provided that the truck is used properly and according to its intended purpose.
Page 52
Safety Residual risk time the truck is used in a manner that falls outside the scope of normal use, and in cases where the driver is not certain that he can use the truck correctly and without the risk of acci- dents.
Page 53
Safety Residual risk 57348011800 EN — 11/2018…
Page 54: Overview Of Hazards And Countermeasures

Safety Residual risk Overview of hazards and counter- measures NOTE This table is intended to help evaluate the hazards in your facility and applies to all drive types. It does not claim to be complete. – Observe the national regulations for the country in which the truck is being used.
Page 55
Safety Residual risk Hazard Measure Check note Notes √ Complete — Not applicable Impermissible usage Issuing of operating German Ordinance on (improper usage) instructions Industrial Safety and Health (BetrSichV) and German Health and labour protection law (ArbSchG) Written notice of German Ordinance on instruction to driver Industrial Safety and…
Page 56
Safety Residual risk Hazard Measure Check note Notes √ Complete — Not applicable When charging the Note the German Association for traction battery Ordinance on Electrical, Electronic Industrial Safety and and Information Health (BetrSichV), Technologies (VDE) the operating regulation 0510: In instructions and the particular German Engineering…
Page 57: Danger To Employees

Safety Residual risk Danger to employees According to the German Ordinance on Indus- trial Safety and Health (BetrSichV) and labour protection law (ArbSchG), the operating com- pany must determine and assess hazards during operation, and establish the labour protection measures required for employ- ees (BetrSichVO).
Page 58: Safety Tests

Safety Safety tests Safety tests Regular safety inspection of the truck Safety inspection based on time and extraordinary incidents The operating company must ensure that the truck is checked by a specialist at least once a year or after particular incidents. As part of this inspection, a complete check of the technical condition of the truck must be performed with regard to accident safety.
Page 59: Particle Filter

Safety Safety tests NOTE Observe the national regulations for the country in which the truck is being used. Particle ﬁlter The truck has an SCR (Selective Catalytic Reduction) exhaust gas treatment system as part of its standard equipment. The truck may be operated in entirely or partially enclosed working areas.
Page 60: Insulation Testing

Safety Safety tests • Employees must be made aware of dangers and protective measures • The particle ﬁlter must be replaced every 6000 operating hours. The exhaust-gas check must be carried out by a competent person (see the chapter entitled «Deﬁnition of terms used for responsible persons») and the results must be recorded in writing NOTE…
Page 61: Safety Regulations For Handling Consumables

Safety Safety regulations for handling consumables Safety regulations for handling consumables Permissible consumables DANGER Failure to observe the safety regulations relating to consumables may result in a risk of injury, death or damage to the environment. – Observe the safety regulations when handling such materials.
Page 62: Hydraulic Fluid

Safety Safety regulations for handling consumables WARNING Prolonged intensive contact with the skin can result in dryness and irritate the skin! – Avoid contact and consumption. – Wear protective gloves. – After any contact, wash the skin with soap and water, and then apply a skin care product.
Page 63: Battery Acid

Safety Safety regulations for handling consumables WARNING These ﬂuids are pressurised during operation of the truck and are hazar- dous to your health. – Do not allow the ﬂuids to come into contact with the skin. – Avoid inhaling spray. –…
Page 64: Diesel Fuel

Safety Safety regulations for handling consumables WARNING Battery acid contains dissolved sulphuric acid. This is corrosive. – When working with battery acid, use appropriate PSA (rubber gloves, apron, protection goggles). – When working with battery acid, never wear a watch or jewellery. –…
Page 65
Safety Safety regulations for handling consumables WARNING Prolonged intensive contact with the skin can result in loss of skin oils and can irritate the skin! – Avoid contact and swallowing. – Wear protective gloves. – After any contact, wash the skin with soap and water, and then apply a skin care product.
Page 66: Coolant And Cooling Fluid

Safety Safety regulations for handling consumables Coolant and cooling ﬂuid WARNING Coolant and cooling ﬂuid can be hazardous to your health and the environment! Coolants are chemical corrosion inhi- bitors and cooling system protecting agents such as Glysantin. The coo- ling ﬂuid is an appropriate mixture of water and coolant.
Page 67
Safety Safety regulations for handling consumables – Neutralise any spilt battery acid immedi- ately. – Always observe national regulations con- cerning the disposal of used oil. 57348011800 EN — 11/2018…
Page 68: Emissions

Safety Emissions Emissions The values speciﬁed apply to a standard truck (compare the speciﬁcations in the «Technical data» chapter). Different tyres, lift masts, additional units etc. may produce different values. Noise emissions The values were determined based on measuring procedures from the standard EN 12053 «Safety of industrial trucks.
Page 69
Safety Emissions Vibrations The vibrations of the machine have been determined on an identical machine in ac- cordance with the standards DIN EN 13059 «Safety of industrial trucks — Test methods for measuring vibration» and DIN EN 12096 «Mechanical vibration — Declaration and veriﬁ- cation of vibration emission values».
Page 70
Safety Emissions Exhaust gases DANGER Risk to health from exhaust gases! Exhaust gases from internal combustion engines are harmful to your health. In particular, the soot particles contained in the diesel exhaust gas can cause cancer. When the internal combustion engine is running, there is a risk of poisoning from the CO, CH and NOx components contained in the exhaust gas.
Page 71: Overviews

Overviews…
Page 72: Overview

Overviews Overview Overview Left-hand side (when viewed in the drive direction) 7341_003-002_V3 Lift mast Drive axle Driver’s compartment Tilt cylinder Overhead guard Fork arms Bonnet Fork carriage Battery maintenance lid Lift cylinder Steering axle 57348011800 EN — 11/2018…
Page 73
Overviews Overview Right-hand side (when viewed in the drive direction) Fresh air ﬁlter for heating system Right-hand service ﬂap AdBlue ﬁller neck Coupling pin Tank ﬁller neck Pre-cleaner 57348011800 EN — 11/2018…
Page 74: Driver’s Compartment

Overviews Driver’s compartment Driver’s compartment Parking brake lever Bottle holder for bottles of max. 0.5 l Steering wheel Driver’s seat Key switch Storage compartment / storage compart- Display and operating unit ment with cover (variant) Document holder / storage compartment for Compartment operating instructions Filler cap for windscreen washer reservoir…
Page 75: Operating Devices And Display Elements

Overviews Operating devices and display elements Operating devices and display elements Display and operating unit Hazard warning system button Operating hours display Front windscreen wiper button Time display (digital) Working spotlight button Particle ﬁlter display Drive programme selector button Rotating beacon display Softkey Lighting Interior lighting display Lighting symbol…
Page 76: Operating Devices For Hydraulic And Driving Functions

Overviews Operating devices and display elements – If you have any questions, please contact your authorised service centre. Operating devices for hydraulic and driving functions Different versions of the operating devices are available for operating the truck’s hydraulic and traction functions. The truck can be equipped with the following operating devices: •…
Page 77: Double Mini-Lever

Overviews Operating devices and display elements Double mini-lever «Lift mast» 360° lever Function key «F1» Function key «F2» «Drive direction/turn indicator» cross lever Function key «5th function» «Attachments» cross lever Signal horn button NOTE Depending on the speciﬁcation, various electric attachment parts can be controlled via function keys (2) and (3).
Page 78: Three-Way Mini-Lever

Overviews Operating devices and display elements Three-way mini-lever 7325_003-026 «Lift mast» 360° lever Function key «5th function» Function key «F1» «Auxiliary hydraulics 1» operating lever Function key «F2» «Auxiliary hydraulics 2» operating lever «Drive direction/turn indicator» cross lever Signal horn button NOTE Depending on the speciﬁcation, various electric attachment parts can be controlled…
Page 79: Four-Way Mini-Lever

Overviews Operating devices and display elements Four-way mini-lever 7325_003-027 «Lift/lower» operating lever Function key «5th function» «Tilt» operating lever «Auxiliary hydraulics 1» operating lever Function key «F1» «Auxiliary hydraulics 2» operating lever Function key «F2» Signal horn button «Drive direction/turn indicator» cross lever NOTE Depending on the speciﬁcation, various electric attachment parts can be controlled…
Page 80: Joystick 4Plus

Overviews Operating devices and display elements Joystick 4Plus 6210_003-087 Horizontal rocker button for «3rd hydraulic LED for clamp locking mechanism (variant) function», tilt the lift mast Slider for the «4th hydraulic function», e.g. Pictograms for the basic hydraulic functions reach frame forwards/backwards Pictograms for the 5th hydraulic function and Vertical rocker button for the «drive direction»…
Page 81: Fingertip

Overviews Operating devices and display elements Fingertip 7325_003-028 Function key «F1» «Attachments» operating lever Function key «F2» «Attachments» operating lever Left turn indicator button «Tilt» operating lever Signal horn button «Lift/lower» operating lever Right turn indicator button Drive direction switch Function key «5th function»…
Page 82: Mini Console

Overviews Operating devices and display elements Mini console The mini console is located on the steering column below the steering wheel. 7311_003-056 Travel direction switch Direction indicator switch 57348011800 EN — 11/2018…
Page 83: Operation

Operation…
Page 84: Testing And Activities Before Daily Use

Operation Testing and activities before daily use Testing and activities before daily use Visual inspections WARNING Risk of injury from falling off the truck! When climbing onto the truck, there is a risk of getting stuck or slipping and falling. Use suitable equipment to reach higher points on the truck.
Page 85
Operation Testing and activities before daily use Component Course of action Check the area under the forklift truck for leaking Underside consumables. Perform a visual inspection for integrity. Overhead guard, guard grille (variant) Check for secure mounting. Make sure they are clean (free of ice, not slippery). Steps Perform a visual inspection for integrity.
Page 86
Operation Testing and activities before daily use Component Course of action Perform a visual inspection for wear and damage. Make sure that only rims of the same type from the same manufacturer are ﬁtted. Wheels, tyres In the event of uneven tyre wear, replace both tyres. Observe the safety regulations in the section entitled «Tyres».
Page 87: Climbing Into And Out Of The Truck

Operation Testing and activities before daily use Climbing into and out of the truck WARNING Risk of injury when climbing into and out of the truck due to slipping, striking parts of the truck or becoming stuck! If the footwell cover is very dirty or smeared with oil, there is a risk of slipping.
Page 88
Operation Testing and activities before daily use Climbing in and out of trucks featuring a single wheel and two steps When climbing into and out of the truck, use the handles (2) and (4) for support. The overhead guard post (1) can also be used for support.
Page 89
Operation Testing and activities before daily use Climbing in and out of trucks featuring two wheels and three steps When climbing into and out of the truck, use the handles (2) and (4) for support. The overhead guard post (1) can also be used for support.
Page 90: Shelves And Cup Holders

Operation Testing and activities before daily use Shelves and cup holders WARNING Risk of accident! Objects that fall into the footwell during travel as a result of steering or braking may slip between the pedals (3) and prevent them from working correctly. It may then be impossible to brake the truck.
Page 91
Operation Testing and activities before daily use WARNING To obtain optimum seat cushioning, you must ad- just the seat suspension to your own body weight. This is better for your back and protects your health. – To prevent injury, make sure that there are no objects within the swivel area of the seat Moving the driver’s seat –…
Page 92
Operation Testing and activities before daily use Adjusting the seat suspension NOTE The driver’s seat can be adjusted to suit the weight of the individual driver. In order to achieve the best seat suspension setting, the driver should perform the adjustment whilst sitting in the seat.
Page 93
Operation Testing and activities before daily use Adjusting the lumbar support (variant) NOTE The lumbar support can be adjusted to suit the contours of the individual driver’s spine. Adjusting the lumbar support moves a convex support cushion into the upper or lower part of the backrest.
Page 94: Adjusting The Armrest

Operation Testing and activities before daily use Switching the seat heater (variant) on and off NOTE The seat heater only functions if the seat contact switch is active, i.e. when the driver is sitting on the driver’s seat. – Switch the seat heater (7) on or off using the switch.
Page 95: Adjusting The Steering Column

Operation Testing and activities before daily use Adjusting the length of the armrest – Release the star-grip handle (1) by turning it anti-clockwise. – Shift the armrest (2) into the desired posi- tion. – Tighten the star-grip handle by turning it clockwise.
Page 96: Unlocking The Emergency Off Switch

Operation Testing and activities before daily use Unlocking the emergency off switch NOTE Only trucks with a joystick 4Plus (variant) have an emergency off switch. – Pull out the emergency off switch (1) until it unlatches. 6321_003-142 Operating the signal horn –…
Page 97: Seat Belt

Operation Testing and activities before daily use Seat belt DANGER Even when using an approved restraint system, there is some residual risk that the driver might be injured if the truck tips over. This risk of injury can be reduced through the combined use of the restraint system and the seat belt.
Page 98
Operation Testing and activities before daily use – Pull the seat belt (3) out of the belt retractor without jerking and fasten closely around the body over the thighs. NOTE Sit as far back as possible so that your back is leaning against the seat backrest.
Page 99
Operation Testing and activities before daily use Releasing the seat belt – Push the red button (4) on the buckle (1). – Manually guide the belt tongue slowly back to the retractor. NOTE Do not allow the seat belt to retract too quickly. The automatic blocking mechanism may be triggered if the belt tongue strikes the housing.
Page 100: Using The Driver’s Cab

Operation Testing and activities before daily use Using the driver’s cab DANGER Risk of fatal injury in the event of falling from the truck if it tips over! In order to prevent the driver from sliding under- neath the truck and being crushed if the truck tips over, a restraint system must be in place and must be used.
Page 101
Operation Testing and activities before daily use Checking the service brake – Release the parking brake. – Depress the brake pedal (1). There must be a slight pedal clearance and then a noticeable pressure point at the brake. – Accelerate the unladen truck in a clear area. –…
Page 102
Operation Testing and activities before daily use WARNING There is no electrical braking assistance when the key switch is switched off! Switching off the key switch will de-energise the entire electrical system. The regenerative brake will not be available. CAUTION There is no power steering when the key switch is switched off! The truck is equipped with hydraulic power stee-…
Page 103: Checking The Steering System For Correct Function

Operation Testing and activities before daily use Checking the steering system for correct function DANGER If the hydraulics fail, there is a risk of accident as the steering characteristics have changed. – Do not operate the truck if it has a defective steering system.
Page 104: Zero Adjustment Of The Load Measurement (Variant)

Operation Testing and activities before daily use CAUTION There is no power steering when the emergency off switch is actuated! The truck is equipped with a hydraulic power stee- ring system. When the emergency off switch is actuated, the hydraulic system is completely shut down.
Page 105
Operation Testing and activities before daily use NOTE Accurate zero adjustment is only possible within the ﬁrst lifting stage of the lift mast. When carrying out the zero adjustment, do not raise the fork more than 800 mm above the ground.
Page 106: Checking The Vertical Lift Mast Position (Variant) For Correct Function

Operation Switching on and starting Checking the vertical lift mast position (variant) for correct function NOTE The function check of the lift mast vertical position (variant) must be carried out every time a truck is commissioned. – Press the Softkey (1).
Page 107
Operation Switching on and starting a straight line. To do this, rotate the steering wheel by approximately half a turn. – Insert the switch key (1) into the key switch and turn to position «I». 5060_003-029_V2 This initiates a self-test. All lamps in the drive direction and turn indicator displays light up brieﬂy.
Page 108
Operation Switching on and starting When the key switch is switched on, the display shows the welcome screen. The truck controller is now fully started up. If the truck is equipped with the «access authorisation with PIN code» variant, the display initially changes to the input menu for access authorisation.
Page 109: Access Authorisation With Pin Code (Variant)

Operation Switching on and starting CAUTION Lack of fuel can cause malfunctions! If the fuel tank has been run empty, the fuel injection system can draw in air bubbles. This can lead to malfunctions in the fuel injection system. When the fuel tank is replaced during repair work or because it has been run empty, diesel fuel must be pre-pumped with the fuel hand pump after ﬁlling, see the «Using the fuel hand pump»…
Page 110
The driver PINs are stored in the truck control unit. These are still available if the display and operating unit has been changed. The authorised service centre can use a diagnostic device to read out the driver PIN and, if necessary, restore the factory default driver PIN.
Page 111
Operation Switching on and starting ACCESS CODE input menu The driver enters the ﬁve-digit driver PIN (00000 to 99999) in this input menu. The driver PIN is entered using the buttons or Softkeys (1). The digits entered for the driver PIN (2) are not visible but are represented by circles instead.
Page 112
Operation Switching on and starting After three invalid entry attempts, the mes- sage appears. The input is CODE DENIED then locked for ﬁve minutes before another attempt can be made. BQ_024_en_V2 Deﬁning the driver PIN NOTE The driver PINs can be deﬁned only by per- sons with the appropriate access authorisa- tion, e.g.
Page 113
Operation Switching on and starting appears in the display. PASSWORD – Enter the four-digit password (factory default: 2777) using the buttons (1). – Conﬁrm the input using Softkey (2). BQ_030_en_V2 appears in the display. CONFIGURATION – Use the drive program selection button (1) and the menu change button (3) to select menu.
Page 114
Operation Switching on and starting Selecting the driver PIN In the menu, there are ﬁfty ACCESS CODE possible driver PINs to choose from. The digit sequences can be set or changed in submenu. NEW CODE Once the menu has been ac- ACCESS CODE cessed, the selection ﬁeld (2) contains…
Page 115
Operation Switching on and starting appears in the display. CONFIRM submenu is used to conﬁrm CONFIRM the new driver PIN. – Enter the new driver PIN for a second time in the ﬁeld (8) using the buttons CONFIRM or Softkeys (7). If the entry matches the new driver PIN previously entered, the system will accept the new driver PIN once the last digit has…
Page 116
Operation Switching on and starting After three incorrect entries, the CODE DE- message appears. NIED The display switches back to the ACCESS menu. The desired driver PIN must be CODE re-deﬁned. BQ_024_en_V2 Changing the password It is recommended that you change the factory default password.
Page 117
Operation Switching on and starting appears in the display. PASSWORD – Enter the current password using the buttons (1). – Conﬁrm the input using Softkey (2). BQ_030_en_V2 appears in the display. CONFIGURATION – Use the drive program selection button (1) and the menu change button (3) to select menu.
Page 118
Operation Switching on and starting appears in PASSWORD/PASSWORD LEVEL the display. – Use the drive program selection button (1) and the menu change button (4) to select the desired (2). PASSWORD LEVEL – Conﬁrm your selection using Soft- (3). BQ_033_en appears in the display.
Page 119: Starting The Engine

Operation Switching on and starting Starting the engine DANGER Risk to health from exhaust gases! Exhaust gases from internal combustion engines are harmful to your health. In particular, the soot particles contained in the diesel exhaust gas can cause cancer. When the internal combustion engine is running, there is a risk of poisoning from the CO, CH and NOx components contained in the exhaust gas.
Page 120
Operation Switching on and starting NOTE If the engine does not start due to a discharged battery, it can be jump-started. NOTE If the truck is left turned off for a lengthy period in ambient temperatures below -5°C, the truck will need to pre-heat at the next start-up.
Page 121: Operating The Display And Operating Unit

Operation Operating the display and operating unit Operating the display and operating unit Displays Standard display elements In the factory setting, the following indicators can be seen in the display and operating unit: Fuel level Shows the fuel level in the fuel tank in %. Drive programme Displays the current drive programme numerically (1-5).
Page 122: Adjusting The Displays

Operation Operating the display and operating unit Adjusting the displays NOTE The parking brake must always be engaged when you adjust the displays. The displays cannot be adjusted if the parking brake is not engaged. NOTE When adjusting the displays, do not actuate the hydraulic system operating devices.
Page 123: Symbols In The Display

Operation Operating the display and operating unit The display changes to the menu. PASSWORD NOTE It may be necessary to enter a password in order to conﬁgure the displays. This depends on the conﬁguration of the display-operating unit. For conﬁguration of the display-operating •…
Page 124
Operation Operating the display and operating unit Description Symbol Service required Lift limitation Reference cycle Battery charging Drive program Hour meter Odometer Daily hour meter Daily odometer Speed Steering angle Load Time Hydraulic system Exh.gas puriﬁer Coolant temperature Fuel level Blue-Q Power rating (average) Power rating (trend)
Page 125
Operation Operating the display and operating unit Symbols for error messages Description Symbol Brake system malfunction Overheating of the engine Overheating Malfunction in the electrical system General malfunction Symbols for softkey functions of auxiliary equipment The following symbols for softkey functions are used on the left of the display for auxiliary equipment: Description…
Page 126
Operation Operating the display and operating unit Description Symbol Seat heater OFF Seat heater ON Signal horn OFF Signal horn ON Cruise control OFF Cruise control ON Automatic mast vertical positioning OFF Automatic mast vertical positioning ON Load measurement zero adjustment OFF Load measurement zero adjustment ON Load measurement OFF Load measurement ON…
Page 127
Operation Operating the display and operating unit Status LEDs of the function keys for additional electrical installations The current switch status of a button is indi- cated with LEDs next to the relevant function key for the additional electrical installation. Description Function off LED OFF…
Page 128: Setting The Date Or Time

Operation Operating the display and operating unit Screen for entering the driver PIN (access code): BQ_038 Setting the date or time – Switch to the menu; CONFIGURATION see the chapter entitled «Adjusting the displays». – Press the Drive programme button (1) or the Menu change button (2) repeatedly until option appears.
Page 129: Resetting The Daily Kilometres And Daily Operating Hours

Operation Operating the display and operating unit Resetting the daily kilometres and daily operating hours 1 2 3 4 The daily number of kilometres and daily operating hours displays can be reset to zero: – Switch to the menu; CONFIGURATION see the chapter entitled «Adjusting the displays».
Page 130: Softkeys For Operating Various Equipment Variants

Operation Operating the display and operating unit – Use the Softkey (3) to exit the menu and return to the next level up. Softkeys for operating various equipment variants Additional functions can be displayed on the display-operating unit. These additional functions, e.g.
Page 131
Operation Operating the display and operating unit STANDARD • Blue-Q is turned off whenever the truck is commissioned. The driver can use the Blue-Q button to switch efﬁciency mode on and off at any time while the truck is being operated FIXED •…
Page 132: Blue-Q Efficiency Mode

Operation Blue-Q efﬁciency mode Blue-Q efﬁciency mode Functional description The Blue-Q efﬁciency mode affects both the drive unit and the activation of the additional consumers, and reduces the truck’s energy consumption. If the efﬁciency mode has been activated, the acceleration behaviour of the truck changes to make acceleration more moderate.
Page 133: Switching Off Additional Consumers

Operation Blue-Q efﬁciency mode Switching off additional consumers If the Blue-Q efﬁciency mode is activated, the controller switches off various additional consumers after a few seconds in certain con- ditions. The additional consumers available depend on the truck equipment. The following table shows the conditions that cause addi- tional consumers to be switched off.
Page 134
Operation Blue-Q efﬁciency mode conﬁguring the Blue-Q operating modes, see the «Conﬁguring Blue-Q efﬁciency mode» sec- tion. – Press the Blue-Q button (2) to switch on Blue-Q. The Blue-Q symbol (1) is displayed. The LED (3) illuminates in blue. Blue-Q efﬁciency mode is switched on.
Page 135: Driving

Operation Driving Driving Safety regulations when driving Driving conduct The driver must follow the public rules of the road when driving in company trafﬁc. The speed must be appropriate to the local conditions. For example, the driver must drive slowly around corners, in tight passageways, when driving through swing-doors, at blind spots, or on uneven surfaces.
Page 136
There is a risk of accident! – Do not use devices during travel or when hand- ling loads. – Set the volume so that warning signals can still be heard. WARNING In areas where use of mobile phones is prohibited, use of a mobile phone or radio telephone is not permitted.
Page 137: Roadways

Operation Driving Roadways Dimensions of roadways and aisle widths The following dimensions and aisle width requirements apply under the speciﬁed conditions to ensure safe manoeuvring. In each case, it must be checked whether a larger aisle width is necessary, e.g. in the case of different load dimensions.
Page 138
Operation Driving Maximum gradient [%] Type Model with load Without load RX70-60 7341 RX70-70 7342 RX70-80 7343 RX70-80 7344 (LSP 900) The stated values are used only to compare performance of trucks in the same category. The gradient values in no way represent the normal daily operating conditions.
Page 139: Setting The Drive Programme

Operation Driving Drainage channels, level crossings and similar objects must be compensated for, and if necessary, ramps must be provided so that trucks can drive over these with as few bumps as possible. Ensure sufﬁcient load capacity of manholes, drain covers and the like. There must be sufﬁcient distance between the highest points of the truck or the load and the ﬁxed elements of the surrounding area.
Page 140: Selecting The Drive Direction

Operation Driving – Push the drive programme button (1) repeatedly until the number of the required drive programme appears on the display (2). Drive programmes 1–5 are available. Essentially, the higher the number of the drive programme, the greater the driving dynamics. The following drive programmes are available: 6311_003-028_V2 Drive programme…
Page 141: Actuating The Drive Direction Switch, Mini-Lever Version

Operation Driving then decelerated and accelerated again in the opposite direction (reversing). The indicator for the selected drive direction («forwards» (1) or «reverse» (2)) lights up on the display and operating unit. Neutral position If the truck is stopped for an extended period, select the neutral position to prevent the truck from suddenly starting if the accelerator pedal is inadvertently pressed.
Page 142: Actuating The Vertical Rocker Switch For The «Drive Direction», Joystick 4Plus Version

Operation Driving Actuating the vertical rocker switch for the «drive direction», joy- stick 4Plus version – For the «forwards» drive direction, push the vertical rocker button for the «drive direction»(1) upwards (A). – For the «reverse» drive direction, push the vertical rocker button for the «drive direction»(1) downwards (B).
Page 143: Actuating The Drive Direction Switch, Mini-Console Version

Operation Driving Actuating the drive direction switch, mini-console version – For the «forwards» drive direction, push the drive direction switch (1) forwards. – For the «backwards» drive direction, push the drive direction switch to the rear. NOTE Alternatively, the drive direction can also be selected using the drive direction switches on the operating devices.
Page 144
Operation Driving The indicator for the selected drive direction («forwards» (1) or «backwards» (2)) lights up on the display and operating unit. NOTE Depending on the equipment, an acoustic signal (variant) may sound a warning during reverse travel, the warning light (variant) may light up or the hazard warning system (variant) may ﬂash.
Page 145: Starting Drive Mode, Dual Pedal Version (Variant)

If the truck still cannot be operated, park the truck securely and contact your authorised service centre.
Page 146
Operation Driving – Actuate the right-hand accelerator pedal (1) to drive «forward» and actuate the left-hand accelerator pedal (2) to drive «backward». NOTE In the dual pedal version, the drive direction switches on the operating devices do not function. 5060_003-085 The indicator for the selected drive direction («forwards»…
Page 147
If the truck still cannot be operated, park the truck securely and contact your authorised service centre.
Page 148: Operating The Service Brake

Operation Driving Operating the service brake The electric brake converts the acceleration energy of the truck into electrical energy. This causes the truck to decelerate. In addition, the truck can be braked using the service brake: – Press the brake pedal (2). In the ﬁrst section of the brake pedal’s travel, only the regenerative braking takes effect.
Page 149: Parking Brake

Operation Driving Zero braking (variant) DANGER Risk of accident! Trucks with zero braking (variant) are not braked when the accelerator pedal is released. – Bring the truck to a standstill by actuating the brake pedal. If your truck features the zero braking equip- ment variant, the electric brake function is disabled.
Page 150
Operation Driving Apply the parking brake – Pull the parking brake lever (1) down fully and release. The parking brake lever swivels back half the distance into the middle position automati- cally. The parking brake is engaged and the wheels are blocked.
Page 151: Steering

Operation Driving Steering DANGER If the hydraulics fail, there is a risk of accident as the steering characteristics have changed. – Do not operate the truck if it has a defective steering system. – Steer the truck by turning the steering wheel (1) accordingly.
Page 152: Reducing Speed When Turning (Curve Speed Control)

DANGER The Curve Speed Control function cannot override the physical limits of stability. Despite this function, there still is a risk of tipping! – Before using this function, familiarise yourself with the change to the driving and steering characteristics of the truck.
Page 153: Driving On Ascending And Descending Gradients

Operation Driving Driving on ascending and descend- ing gradients DANGER Danger to life! Driving on ascending and descending gradients carries special dangers! – Always follow the instructions below. – On ascending and descending gradients, the load must be carried facing uphill. –…
Page 154: Reducing Speed With A Raised Load (Variant)

Operation Driving Reducing speed with a raised load (variant) This function (variant) reduces the speed of the truck with a raised load. 7321_003-052_en_V2 Automatic shut-off of the internal combustion engine (variant) The truck is equipped with an automatic shut-off function that shuts off the internal combustion engine when certain conditions apply simultaneously after a preset waiting STOP…
Page 155: Parking

Operation Parking Parking Parking the truck securely and switching it off DANGER Risk of fatal injury from being run over if the truck rolls away! – The truck must not be parked on a slope. – In emergencies, secure the truck using wedges on the side facing downhill.
Page 156: Wheel Chock (Variant)

Operation Parking Wheel chock (variant) The wheel chock (variant) is used to prevent the truck from rolling away on a slope. – Lift handle (2) on the support mounting. – Remove wheel chock (1) from the support mounting. – Push the wheel chock under a front axle wheel on the side facing the downhill slope.
Page 157: Lifting

Operation Lifting Lifting Lifting system variants The movement of the fork carriage and the lift mast heavily depends on the following equipment: • The lift mast with which the truck is equipped, see ⇒ Chapter «Types of lift mast», P. 4-150 •…
Page 158: Lift Mast Vertical Position (Variant)

Operation Lifting Overriding and reactivating the auto- matic lift cut out If a load needs to be lifted to the truck’s maximum lift height and the automatic lift cut out function is not required, it is possible to override the lift cut out. It is automatically reactivated when the truck is switched off and back on again.
Page 159
Operation Lifting CAUTION Risk of damage to property due to the lift mast colliding with racks or other objects! – Before using the «lift mast vertical position» comfort feature, position the truck at a sufﬁcient distance from racks and other objects. The «lift mast vertical position»…
Page 160
Operation Lifting Automatic approach towards the «lift mast vertical position» – Switch on the «lift mast vertical position» comfort feature via the button (1) on the display and operating unit. – Tilt the lift mast forwards using the corre- sponding operating device. The lift mast stops automatically as soon as the prese- lected setting is reached for the «lift mast vertical position».
Page 161
Operation Lifting The lift mast is tilted forwards and stops as soon as the vertical position is reached. The arrow above the bar shown on the screen of the display and operating unit represents the «lift mast vertical position». Tilt the lift mast forwards beyond the vertical position: –…
Page 162: Types Of Lift Mast

Operation Lifting Calibrating the «lift mast vertical position» – Set the lift mast to the required position. – Press and hold the button (1) for the «lift mast vertical position» for at least ﬁve seconds. The message » » ? VERTICAL POSITION will appear on the display.
Page 163: Malfunctions During Lifting Mode

Operation Lifting Triplex lift mast (variant) During lifting, the inner lift cylinder moves up to free lift (3), and then the outer lift cylinders raise the inner lift mast up to the max. height (2). DANGER Risk of accident due to collision of the lift mast or load with low ceilings or entrances.
Page 164: Hydraulic Blocking Function

Operation Lifting Load chains not under tension DANGER Danger caused by a falling load! – Make sure that the chain(s) does (do) not become slack when lowering the load. Slack chains can, for instance, result from: • Resting the fork carriage or the load on the racking.
Page 165: Lifting System Operating Devices

Operation Lifting – Sit down on the driver’s seat. All the relevant functions of the working hydraulics will be available again. NOTE If it is not possible to release the block on the hydraulics when the load is raised because of a technical fault, the load must be lowered using the «emergency lowering»…
Page 166: Controlling The Lifting System Using A Double Mini-Lever

Operation Lifting Controlling the lifting system using a double mini-lever DANGER Reaching into or climbing between moving parts of the truck (e.g. lift mast, sideshifts, working equipment, load carrying devices etc.) can lead to serious injury or death and is therefore prohibited. –…
Page 167: Controlling The Lifting System Using A Triple Mini-Lever

Operation Lifting Controlling the lifting system using a triple mini-lever DANGER Reaching into or climbing between moving parts of the truck (e.g. lift mast, sideshifts, working equipment, load carrying devices etc.) can lead to serious injury or death and is therefore prohibited. –…
Page 168: Controlling The Lifting System Using A Quadruple Mini-Lever

Operation Lifting Controlling the lifting system using a quadruple mini-lever DANGER Reaching into or climbing between moving parts of the truck (e.g. lift mast, sideshifts, working equipment, load carrying devices etc.) can lead to serious injury or death and is therefore prohibited. –…
Page 169: Controlling The Lifting System Using The Joystick 4Plus

Operation Lifting Controlling the lifting system using the joystick 4Plus DANGER Reaching into or climbing between moving parts of the truck (e.g. lift mast, sideshifts, working equipment, load carrying devices etc.) can lead to serious injury or death and is therefore prohibited. –…
Page 170
Operation Lifting Tilting the lift mast To tilt the lift mast forwards: – Tilt the horizontal rocker button (2) to the left (C). To tilt the lift mast backwards: – Tilt the horizontal rocker button (2) to the right (D). 6210_003-090 7312_003-022_V2 Fork-carriage sideshift…
Page 171: Controlling The Lifting System Using The Fingertip

Operation Lifting Controlling the lifting system using the ﬁngertip DANGER Reaching into or climbing between moving parts of the truck (e.g. lift mast, sideshifts, working equipment, load carrying devices etc.) can lead to serious injury or death and is therefore prohibited. –…
Page 172: Changing The Fork Arms

Operation Lifting Changing the fork arms DANGER Risk of fatal injury from being run over if the truck rolls away! – Do not park the truck on a gradient. – Apply the parking brake. – Change the fork arms in a separate, safe location on a level surface.
Page 173
Operation Lifting Removal – Select a pallet corresponding to the fork arm size. – Set down the pallet next to the fork carriage on the side chosen for removal. – Lift the fork carriage until the fork arms are approx. 3 cm above the pallet. –…
Page 174: Fork Extension (Variant)

Operation Lifting ged. Otherwise, correct load measurement cannot be guaranteed. Fork extension (variant) DANGER There is a risk of being run over if the truck rolls away and therefore a danger to life. – Do not park the truck on a slope. –…
Page 175
Operation Lifting Attachment DANGER Risk to life from falling load! At least 60% of the length of the fork extension must lie on the fork arm. A maximum 40% overhang over the fork arm end is permissible. The fork extension must also be secured against slipping from the fork arm.
Page 176: Operation With Reversible Fork Arms (Variant)

Operation Lifting Operation with reversible fork arms (variant) DANGER Risk to life from falling load! Standard fork arms are not structurally designed for reverse operation. If this instruction is not observed, it can lead to material failure and the load falling. –…
Page 177
Operation Lifting Reversible fork arms (1) can be used to reach an additional lift height. The reversible fork arms are installed on the fork carriage in the same manner as standard fork arms. Loads may be lifted on and beneath the reversible fork arms.
Page 178: Handling Loads

Operation Handling loads Handling loads Safety regulations when handing loads The safety regulations for handling loads are shown in the following sections. DANGER There is a risk to life caused by falling loads or if parts of the truck are being lowered. –…
Page 179: Before Taking Up Load

Operation Handling loads Before taking up load Load capacity The load capacity indicated for the truck on the capacity rating plate may not be exceeded. The load capacity is inﬂuenced by the load centre of gravity and the lift height as well as by the tyres, if applicable.
Page 180: Load Measurement (Variant)

Operation Handling loads Example Weight of load to be lifted: 880 kg (3) Load distance from fork back: 500 mm (1) Permitted lift height: 5230 mm (2) WARNING Risk of accident from the truck losing stability! The permissible load of the attachments (variant) and the reduced lifting capacity of the combination 5230 of truck and attachment must not be exceeded.
Page 181
Operation Handling loads The load measurement has an accuracy of +/-3% of the rated capacity of the truck. NOTE In order to ensure accuracy at all times, a zero adjustment of the load measurement must be carried out. Zero adjustment is required. as part of daily commissioning •…
Page 182
Operation Handling loads NOTE The method of operating the lifting system depends on the operating devices included in the truck’s equipment. – Ensure that the truck has been in operation for a period of time before carrying out the load measurement. –…
Page 183: Picking Up Loads

Operation Handling loads When load measurement has been performed correctly, the determined load weight (3) is shown on the display. NOTE If the load measurement is invalid, the value «-9999 kg» is displayed in the operating unit. 6210_003-073_en Picking up loads To make sure that the load is securely sup- ported, it must be ensured that the fork arms are sufﬁciently far apart and are positioned as…
Page 184: Danger Area

Operation Handling loads Adjusting the fork – Lift the locking lever (1) and move the fork arms to the desired position. – Allow the locking lever to snap back into place. The load centre of gravity must be midway between the fork arms. –…
Page 185: Transporting Pallets

Operation Handling loads DANGER Danger of death from falling loads! – Never walk or stand underneath suspended loads. Transporting pallets As a rule, loads (e.g. pallets) must be transpor- ted individually. Transporting multiple loads at the same time is only permitted: •…
Page 186: Load Pick Up

Operation Handling loads DANGER Loss of stability. Slipping or swinging suspended loads can lead to a loss of stability and cause the truck to tip over. – When transporting suspended loads, observe the following instructions Instructions for transporting suspended loads: •…
Page 187
Operation Handling loads equipment and incorrectly formed loads must not be stored. – Attach or secure the load to the load- carrying equipment so that the load cannot move or fall. – Store the load so that the speciﬁed aisle width is not reduced by protruding parts.
Page 188
Operation Handling loads – Insert the fork as far under the load as possible. Stop the truck as soon as the fork back is resting on the load. The centre of gravity of the load must be positioned between the fork arms in the middle. 6210_800-007 –…
Page 189
Operation Handling loads – Lower the load while maintaining ground clearance. 5060_003-102 – Tilt the lift mast backwards. The load can be transported. 5060_003-101 57348011800 EN — 11/2018…
Page 190: Transporting Loads

Operation Handling loads Transporting loads NOTE Observe the information in the chapter entitled «Safety regulations when driving». DANGER The higher a load is lifted, the less stable it beco- mes. The truck can tip over or the load can fall, increasing the risk of accident! Driving with a raised load and the lift mast tilted forward is not permitted.
Page 191: Setting Down Loads

Operation Handling loads – Never drive with a load protruding to the side (e.g. with the sideshift)! 6210_800-014 Setting down loads DANGER Risk of accident due to changed moment of tilt! The load centre of gravity and the moment of tilt move due to tilting the lift mast forwards with a raised load or due to the load slipping.
Page 192
Operation Handling loads – Drive up to the stack with the load lowered in accordance with regulations. – Set lift mast to vertical. – Lift the load to the stacking height. – Drive the truck towards the rack carefully. 6210_800-015 –…
Page 193: Driving On Lifts

Operation Handling loads Driving on lifts The driver may only use this truck on lifts with a sufﬁcient rated capacity and for which the operating company has been granted authorisation. DANGER There is a risk to life if you are crushed or run over by the truck.
Page 194: Driving On Loading Bridges

Operation Handling loads Driving on loading bridges DANGER Risk of accident if the truck crashes! Steering movements can cause the tail end to veer off the loading bridge towards the edge. This may cause the truck to crash. The lorry driver and the truck driver must agree on the lorry’s departure time.
Page 195: Particle Filter System

Operation Particle ﬁlter system Particle ﬁlter system Particle ﬁlter — Function DANGER Risk to health from exhaust gases! Exhaust gases from internal combustion engines are harmful to your health. In particular, the soot particles contained in the diesel exhaust gas can cause cancer.
Page 196
Operation Particle ﬁlter system In addition, very low ambient temperatures may prevent a sufﬁciently high exhaust gas temperature being reached. This causes the regeneration process to be disrupted. The soot ﬁltered out of the exhaust gas then collects in the particle ﬁlter, as it is not burned off during the continuous regeneration process.
Page 197: Particle Filter — Performing Parked Regeneration

Operation Particle ﬁlter system Particle ﬁlter — Performing parked regeneration CAUTION Risk of damage to components! If parked regene- ration is not performed when required, the particle ﬁlter may become damaged. A full parked regeneration must be performed in order to completely empty the particle ﬁlter. CAUTION During the parked regeneration process, very hot combustion gases escape from the exhaust pipe!
Page 198
Operation Particle ﬁlter system • Remove any connected exhaust gas extraction units • Perform parked regeneration in a suitable place NOTE Parked regeneration can only be performed if the parking brake is engaged. If the parking brake is not engaged, APPLY HANDBRAKE! appears on the display.
Page 199
Operation Particle ﬁlter system The message as well START PARK. REG.? as the soft keys (1) and (2) appear on the display. – To start the parked regeneration process, press the button (1). The message appears START IC ENGINE on the display. –…
Page 200: Particle Filter — Displays

Operation Particle ﬁlter system The particle ﬁlter regeneration process is started. EXH.GAS PURIFIER PLEASE appears on the display. The status WAIT bar (4) below the message indicates the regeneration progress. NOTE During parked regeneration, the engine speed ﬂuctuates and the power of the radiator fan is reduced.
Page 201
Operation Particle ﬁlter system relating to parked regeneration and if parked regeneration is not performed: Messages Meaning Comment Carry out parked regeneration See the section entitled «Per- EXH.GAS PURIFIER of the particle ﬁlter. forming parked regeneration» Prompt asking whether parked START regeneration of the particle ﬁlter PARK.
Page 202: Attachments

Fitting attachments If the truck is equipped with an integrated attachment (variant) at the factory, the speciﬁ- cations in the STILL operating instructions for integrated attachments must be observed. If attachments are ﬁtted at the place of use, the speciﬁcations in the operating instructions of the attachment manufacturer must be observed.
Page 203
Operation Attachments DANGER There is risk to life caused by a falling load! Attachments that hold the load by exerting pressure on it (e.g. clamps) must be additionally controlled by a second operating function (lock) that is actuated to prevent an unintentional release of the load. If such an attachment is retroﬁtted, a second opera- ting function for actuation must also be retroﬁtted.
Page 204: Releasing The Pressure From The Hydraulic System

Operation Attachments Load capacity with attachment The permissible load capacity of the attach- ment and the allowable load (load capacity and load moment) of the truck must not be ex- ceeded by the combination of attachment and payload. The speciﬁcations of the manufac- turer and supplier of the attachment must be complied with.
Page 205
Operation Attachments – Actuate the operating lever (1) for control- ling the hydraulic functions repeatedly in the direction of the arrow, as far as the end position. The valves open and the hydraulic system is depressurised. – Switch off the key switch. 7312_003-184 57348011800 EN — 11/2018…
Page 206: General Instructions For Controlling Attachments

Operation Attachments General instructions for controlling attachments The way in which attachments (variant) are controlled depends on the operating devices included in the truck’s equipment. Essentially, a distinction is drawn between: • Double mini-lever • Double mini-lever with a 5th function (variant) •…
Page 207
Operation Attachments NOTE All the attachments described fall into the category of equipment variants. Please see the respective operating instructions for an exact description of the respective movements/actions of the attachment ﬁtted. 57348011800 EN — 11/2018…
Page 208: Controlling Attachments Using A Double Mini-Lever

Operation Attachments Controlling attachments using a double mini-lever The attachments (variants) are controlled in this version using the «attachments» cross lever (1). The pictograms on the «attachments» cross lever show the respective functions that are activated by this lever. This essentially involves the following: –…
Page 209
Operation Attachments – Note the following attachment functions and pictograms. Move sideshift frame or fork forwards Move sideshift frame or fork back- wards Move sideshift to the left Move sideshift to the right Adjust fork arms: open Adjust fork arms: close Swivel lift mast or fork to the left Swivel lift mast or fork to the right Release load retainer…
Page 210: Controlling Attachments Using The Double Mini-Lever And The 5Th Function

Operation Attachments Controlling attachments using the double mini-lever and the 5th function NOTE For technical reasons, clamping attachments must not be controlled via the 5th function. NOTE The «lift mast» 360° lever (3) and the «attach- ments» cross lever (2) control four hydraulic functions.
Page 211
Operation Attachments – Note the following attachment functions and pictograms. Move sideshift frame or fork forwards Move sideshift frame or fork back- wards Move sideshift to the left Move sideshift to the right Adjust fork arms: open Adjust fork arms: close Swivel lift mast or fork to the left Swivel lift mast or fork to the right Release load retainer…
Page 212: Controlling Attachments Using A Triple Mini-Lever

Operation Attachments Controlling attachments using a triple mini-lever The attachments (variant) are controlled in this version using operating levers (1) and (2). The pictograms on the operating levers show the respective functions that are activated by these levers. This essentially involves the following: –…
Page 213
Operation Attachments – Note the following attachment functions and pictograms! Move sideshift frame or fork forwards Move sideshift frame or fork back- wards Move sideshift to the left Move sideshift to the right Adjust fork arms: open Adjust fork arms: close Swivel lift mast or fork to the left Swivel lift mast or fork to the right Release load retainer…
Page 214: Controlling Attachments Using The Triple Mini-Lever And The 5Th Function

Operation Attachments Controlling attachments using the triple mini-lever and the 5th function NOTE For technical reasons, clamping attachments cannot be controlled via the 5th function. NOTE The «lift mast» 360° lever (3) and operating levers (1) and (2) control four hydraulic functions.
Page 215
Operation Attachments – Note the following attachment functions and pictograms. Adjust fork arms: open Adjust fork arms: close Rotate to the left Rotate to the right 5060_003-122 57348011800 EN — 11/2018…
Page 216: Controlling Attachments Using A Quadruple Mini-Lever

Operation Attachments Controlling attachments using a quadruple mini-lever The attachments (variant) are controlled in this version using operating levers (1) and (2). The pictograms on the operating levers show the respective function that is activated by these levers. This essentially involves the following: –…
Page 217
Operation Attachments – Note the following attachment functions and pictograms! Move sideshift frame or fork forwards Move sideshift frame or fork back- wards Move sideshift to the left Move sideshift to the right Adjust fork arms: open Adjust fork arms: close Swivel lift mast or fork to the left Swivel lift mast or fork to the right Release load retainer…
Page 218: Controlling Attachments Using The Quadruple Mini-Lever And The 5Th Function

Operation Attachments Controlling attachments using the quadruple mini-lever and the 5th function NOTE For technical reasons, clamping attachments cannot be controlled via the 5th function. NOTE Operating levers (1) to (4) are used to control four hydraulic functions. The designation «5th function»…
Page 219
Operation Attachments – Note the following attachment functions and pictograms. Adjust fork arms: open Adjust fork arms: close Rotate to the left Rotate to the right 5060_003-122 57348011800 EN — 11/2018…
Page 220: Controlling Attachments Via The Joystick 4Plus

Operation Attachments Controlling attachments via the joystick 4Plus In this equipment, the attachments (variant) are controlled via the joystick 4Plus (1). The pictograms on the decal information about operation of the joystick 4Plus show the respective functions that are activated by the individual operating devices of the joystick 4Plus.
Page 221: Controlling Attachments Using The Joystick 4Plus And The 5Th Function

Operation Attachments Controlling attachments using the joystick 4Plus and the 5th function NOTE For technical reasons, clamping attachments cannot be controlled via the 5th function. NOTE The 5th hydraulic function can be used to control an attachment. The pictograms on the joystick 4Plus show which attachment functions can be controlled using the 5th function.
Page 222: Controlling The Attachments With The Fingertip

Operation Attachments Controlling the attachments with the ﬁngertip The attachments (variant) are controlled in this version using the operating levers (1). The pictograms on the operating levers show the functions that are activated by that lever. – Move the operating lever (1) forwards The attachment moves in the direction of movement shown in the upper part of the pictogram.
Page 223: Controlling Attachments With The Fingertip And 5Th Function

Operation Attachments Controlling attachments with the ﬁngertip and 5th function NOTE For technical reasons, clamping attachments cannot be controlled via the 5th function. NOTE The designation «5th function» refers to the fact that the four operating levers control four functions, while the «5th function» can be controlled by switching functions.
Page 224
Operation Attachments – Press function key (4) NOTE The arrow (5) under the function key indicates which operating lever is equipped with the «5th function». The «5th function» is switched to the 3rd operating lever; see sticker (6). 7325_003-045 – Press function key (7) NOTE The arrow (8) under the function key indicates which operating lever is equipped with the «5th…
Page 225: Clamp Locking Mechanism (Variant)

Operation Attachments – Note the following attachment functions and pictograms. Move side shift frame or fork for- wards/backwards Move sideshift to the left/right Adjust fork arms: open/close Swivel lift mast or fork to the left/right Release/clamp load retainer Push off/pull in load Turn to the left/right Tip shovel over/tip shovel back 6210_003-035…
Page 226
Operation Attachments Double mini-lever – To release the clamp locking mechanism, push the cross lever (1) forwards. The LED for button (2) lights up as long as the clamp locking mechanism is released. NOTE The hydraulic function for opening the clamp is available for one second after the clamp locking mechanism is released.
Page 227
Operation Attachments Quadruple mini-lever – To release the clamp locking mechanism, push the operating lever (1) forwards. The LED for button (2) lights up as long as the clamp locking mechanism is released. NOTE The hydraulic function for opening the clamp is available for one second after the clamp locking mechanism is released.
Page 228: Taking Up A Load Using Attachments

Operation Attachments Fingertip switch – To release the clamp locking mechanism, push the operating lever (1) forwards. The LED for button (2) lights up as long as the clamp locking mechanism is released. NOTE The hydraulic function for opening the clamp is available for one second after the clamp locking mechanism is released.
Page 229: Auxiliary Equipment

Operation Auxiliary equipment • Load capacity Q (kg) (1) • Lift height h (mm) (2) • Load distance C (mm) (3) Auxiliary equipment Switching the lighting on and off Driving lights – To switch on the parking light, press the button (1).
Page 230: Switching The Working Spotlight For Reverse Travel On And Off

Operation Auxiliary equipment Working spotlights – To switch on the working spotlights (front and rear), press the button (1). The working spotlights light up. – To switch off the working spotlights, press the button (1) again. The working spotlights go out. NOTE In trucks with StVZO (German Road Trafﬁc Licensing Regulations) equipment (variant),…
Page 231: Switching The Rotating Beacon On And Off

Operation Auxiliary equipment Switching the rotating beacon on and – Press the Softkey (1) to switch on the rotating beacon. The rotating beacon is switched on. The symbol is displayed. – To switch off the rotating beacon, press the Softkey The rotating beacon goes out.
Page 232: Switching The Turn Indicators On And Off

Operation Auxiliary equipment Switching the turn indicators on and Mini-lever version – Switch on the turn indicators by moving the cross lever of the drive direction/turn indicator (1) to the left or to the right. 5060_003-096 The turn indicators and the corresponding turn indicator displays (2) or (3) ﬂash.
Page 233
Operation Auxiliary equipment Mini-console version – Switch on the turn indicators by moving the turn indicator switch (1) to the left or to the right. 5060_003-046 The turn indicators and the corresponding turn indicator displays (2) or (3) ﬂash. – Switch off the turn indicators by moving the turn indicator switch to the centre position.
Page 234: Switching The Double Working Spotlights On And Off

Operation Auxiliary equipment Switching the double working spotlights on and off. The double working spotlights are ﬁtted up on the front right and left on the overhead guard. Each double working spotlight consists of an upper working spotlight (2) and a lower working spotlight (3).
Page 235
Operation Auxiliary equipment – Press Softkey (1) to switch on the working spotlights. The working spotlights are switched on. The symbol is displayed. – Press Softkey to switch off the working spotlights. The working spotlights are switched off. The symbol is displayed. Switching the upper working spotlights on/off automatically –…
Page 236: Still Safetylight (Variant)

Danger of damage to eyes from looking into the STILL SafetyLight. Do not look into the STILL SafetyLight. The STILL SafetyLight is a visual warning unit designed to enable early detection of trucks in driving areas with low visibility (such as drive lanes, high racks), as well as at blind junctions.
Page 237: Operating The Windscreen Wiper/Washer

Operation Auxiliary equipment NOTE If the truck is to be operated on public roads, the STILL SafetyLight must be switched off. Operating the windscreen wiper/washer – Press the button (1) to activate the front wiper/washer (variant) and the roof panel wiper (variant).
Page 238: Fleetmanager (Variant)

Operation Auxiliary equipment – Open ﬁller cap (2) for the windscreen washer reservoir. – Fill the windscreen washer reservoir with washer ﬂuid and anti-freeze in accor- dance with the maintenance data table; see ⇒ Chapter «Maintenance data ta- ble», P. 5-326. –…
Page 239
Operation Auxiliary equipment NOTE The cruise control function cannot be used for reverse travel or when travelling at speeds below 6.0 km/h. Depending on the truck equipment, the cruise control can be switched on and off via the drive direction switch or the display and operating unit.
Page 240
Operation Auxiliary equipment Switching on and off using the Softkeys on the display-operating unit. Switching on cruise control WARNING Risk of accident from failing to adjust speed! Driving at excessive speeds can cause accidents, e.g. the truck could tip over when cornering. –…
Page 241
Operation Auxiliary equipment The current speed is saved. The forward travel indicator (2) ﬂashes. Cruise control is switched on. The symbol is displayed. – Remove your foot from the accelerator pedal. The truck continues to drive at the selected speed until the cruise control function is switched off again.
Page 242: 12-V Socket

Operation Auxiliary equipment The forward travel indicator (2) illuminates. Cruise control is switched off. The symbol is displayed. NOTE If the truck is conﬁgured with automatic functions that reduce the driving speed to 6 km/h or less in certain situations, then these functions will also switch the cruise control off automatically.
Page 243: Driver Restraint Systems (Variants)

Operation Auxiliary equipment Driver restraint systems (variants) Different driver restraint systems are available as variants for this truck. The description and operation for these systems can be found in the separate «Driver restraint systems» operating instructions. Ceiling sensor (variant) Description The ceiling sensor (1) on the overhead guard is an assistance system that automatically reduces the driving speed of the truck within…
Page 244
Before the truck is able to accelerate to the maximum speed permitted for outdoor areas, the speed limitation must still be unlocked. To do this, release the accelerator brieﬂy and then operate the accelerator again. • Switching on the truck in a hall…
Page 245
Operation Auxiliary equipment – On the underside of the assembly baseplate on the overhead guard, loosen the four nuts (1) on the sensor. – Carefully remove the sensor. – Using the supplied key (2), open the sensor housing to gain access to the DIP switches. 57348011800 EN — 11/2018…
Page 246
Operation Auxiliary equipment – Using the DIP switches «1» to «5» (3), adjust the range and the sensitivity of the sensor. The DIP switches can be adjusted using a small screwdriver. CAUTION The settings for DIP switches «6» to «8» are the factory settings of the manufacturer.
Page 247
Operation Auxiliary equipment sensitivity that has been set. See the following table: Sensitivity Range Beam angle 22.5° 22.5° Low (1) 20° 16 m 15° 24 m 5° 35° 30° Medium (2) 25° 16 m 22.5° 24 m 10° Sensitivity Range Beam angle 42°…
Page 248
Operation Auxiliary equipment Representation of the beam angle depending on the sensitivity of the sensor that has been set, from (1)»low» to (4)»very high». 2 3 4 Additional labelling Adhesive label next to the display-operating unit 57348011800 EN — 11/2018…
Page 249: Cab

Operation Opening the cab door DANGER There is a risk of damage caused by collision if the cab door opens while driving. – The cab door must be latched securely in the engaged position. Opening the cab door from the outside: –…
Page 250: Closing The Cab Door

Operation Closing the cab door DANGER There is a risk of damage caused by collision if the cab door opens while driving. – The cab door must be latched securely in the engaged position. Opening the side windows WARNING There is a risk of crushing between the window frame and side window from the side windows slipping inadvertently during travel.
Page 251: Operating The Interior Lighting

Operation Closing the front side window: The front side window (4) can be closed in the same way as the rear side window. Operating the interior lighting An interior light (1) with swivelling support (3) is ﬁtted in the right-hand roof lining of the cab. The interior lighting can be operated using the switch (2) in the roof lining and via the corre- sponding Softkey on the display-operating…
Page 252: Operating The Rear Window Heating

Operation – To switch off the interior lighting, press the Softkey (1). The interior lighting is switched off. The symbol (2) is displayed. NOTE We do not recommend that you use the switch in the roof lining to turn off the interior lighting.
Page 253: Radio (Variant)

There is a risk of accident! – Do not use the radio when driving or when handling loads. 6321_003-015 – Set the radio volume so that you can still hear warning signals. Heating system (variant) DANGER Risk of explosion!
Page 254
Operation DANGER Risk of burns! When the heating system is operated, the heating system housing becomes hot and can burn the skin if it is touched. – Do not touch the heating system housing during operation. CAUTION Risk of blower malfunction! The fresh air ﬁlter and recirculated air ﬁlter collect dust and dirt particles from the intake air.
Page 255: Air Conditioning (Variant)

Operation Adjusting the air ﬂow – Adjust the air ﬂow at the front outlet vents (3) and at the outlet vent in the footwell (4). 7331_345-002 Air conditioning (variant) Switching on the air conditioning – Switch the blower switch (1) on. –…
Page 256: Push-Up Roof Window (Variant)

Operation Push-up roof window (variant) WARNING Risk of crushing! – When closing the roof window, do not reach between the roof window and the overhead guard. – Do not reach in to touch components as they are being closed. The push-up roof window (1) is an equipment variant.
Page 257: Trailer Operation

Operation Trailer operation Trailer operation Towed load DANGER There is an increased risk of accident when using a trailer. Using a trailer changes the truck handling charac- teristics. When towing, operate the truck such that the trailer train can be safely driven and braked at all times.
Page 258: Coupling Pin In The Counterweight

Operation Trailer operation CAUTION Damage to the tow coupling due to overloading! Tow couplings RO*243 and RO*244 must be individually checked to ensure that they are suitable for the planned towing operation. The permissible rigidity value of the tow coupling must always be taken into account.
Page 259
Operation Trailer operation – Take measures to prevent the trailer from rolling away, e.g. use wheel chocks (1). 7090_900-008 – Push the coupling pin (2) down, turn 90° and pull out. – Adjust tiller height. DANGER Persons may become trapped between the truck and trailer.
Page 260: Automatic Tow Coupling

Operation Trailer operation Uncoupling the trailer – Take measures to prevent the trailer from rolling away, e.g. use wheel chocks. – Push the coupling pin (2) down, turn 90° and pull out. – Slowly move the truck forwards and guide the tow-bar eye completely out of the counterweight.
Page 261
Operation Trailer operation DANGER If you brieﬂy leave the truck to couple or uncouple, there is a risk to life caused by the truck rolling away and running you over. – Apply the parking brake. – Lower the fork to the ground. –…
Page 262
Operation Trailer operation CAUTION Risk of component damage if the tiller in the tow coupling is tilted! The tiller should if possible be kept horizontal when towing. This ensures a sufﬁcient rotation range at the top and bottom. The authorised service centre can adjust the assembly height for the tow coupling to the tiller height if necessary.
Page 263
Operation Trailer operation – Pull out the safety handle (3). – Push the hand lever (2) upwards. DANGER Persons may become trapped between the truck and trailer. When hooking up, ensure that no one is between the truck and trailer. CAUTION When being coupled, the tow-bar eye must engage in the middle of the coupling jaw.
Page 264
Operation Trailer operation Uncoupling model RO*243 – Take measures to prevent the trailer from rolling away, e.g. use wheel chocks. – Pull out the safety handle (3). – Push the hand lever (2) upwards. – Slowly drive the truck forwards until the tow- bar eye and towing jaws are disconnected.
Page 265
Operation Trailer operation DANGER Persons may become trapped between the truck and trailer! When hooking up, ensure that no one is between the truck and trailer. CAUTION When being coupled, the tow-bar eye must engage in the middle of the coupling jaw. Failure to follow these instructions could result in damage to the coupling jaw or to the tow-bar eye! –…
Page 266
Operation Trailer operation Closing model RO*244 A by hand DANGER Risk of injury from hand becoming trapped! Do not reach into the coupling pin area with your hand. If, for example, a tow rope is to be secured in the tow coupling, only actuate the tow coupling via the closing lever (1).
Page 267
Operation Trailer operation Coupling model RO*245 NOTE Tow coupling RO 245 is intended for a tow-bar eye in accordance with DIN 74054 (bore diameter 40 mm) or DIN 8454 (bore diameter 35 mm). – Take measures to prevent the trailer from rolling away, e.g.
Page 268: Towing Trailers

Operation Trailer operation Uncoupling model RO*245 – Take measures to prevent the trailer from rolling away, e.g. use wheel chocks. – Push the hand lever (5) upwards. – Slowly drive the truck forwards until the tow- bar eye and towing jaws are disconnected. –…
Page 269: Display Messages

Operation Display messages Display messages Display content On the display of the display-operating unit, event-related messages may appear due to certain truck conditions. The following types of message may appear individually or in combination: • A graphic symbol (2) • The message (3) •…
Page 270: Error Code Table

Operation Display messages Error code table The table gives an overview of possible displays. In the «Comment» column, you will ﬁnd information on how to proceed should any of these messages be displayed. Message text/ Comment Error code Control unit A1401 Control unit A1431…
Page 271
Seat switch has not been operated for approx. 8 hours. SEAT SWITCH A3027 Truck can possibly still be driven at a reduced speed and with reduced lifting capacity. Stand up brieﬂy and then sit down again. If this does not resolve the problem, contact your authorised service centre.
Page 272
Operation Display messages Message text/ Comment Error code Drive unit not functioning. SURVEILLANCE A2801 Release accelerator pedal. A2802 If this error occurs sporadically, it can be tolerated. If the A2808 operational capacity is impaired, notify your authorised A2809 service centre. A2810 A2815 Drive direction is set to neutral.
Page 273: General Messages

Message text/ Comment Error code Engine control unit (ECU) reports engine error. V-engine malfunction A5821 Truck can still be operated. Notify your authorised service centre. Engine control unit (ECU) reports serious engine error, Switch off immediately! switch engine off immediately. V-engine A5822 Truck only moves at emergency mode speed.
Page 274
However, the truck can still roll until the drive wheel units are blocked. For this reason, the parking brake must always be applied before you leave the…
Page 275
Operation Display messages – Notify the authorised service centre. SWITCH OFF TRUCK? message If the message SWITCH OFF THE TRUCK? appears on the display, the switching-off of the truck is veriﬁed. – Press the corresponding softkey on the display and operating unit to switch off the truck or cancel the operation.
Page 276
Operation Display messages The fork is not lowered. If the fork is above the height sensor, the key switch is turned off and the seat vacated, message appears in LOWER FORKS the display (variant). An optional signal tone sounds. – Lower the fork to the ground. The message disappears.
Page 277
Operation Display messages ? VERTICAL POSITION If the message ? VERTICAL POSITION appears on the display, calibration of the «vertical lift mast position» has been activated. – Save the mast position or cancel the calibration. REFERENCE CYCLE message If the fork was lowered after the truck was switched off, the control electronics do not know the position of the fork when the truck is restarted.
Page 278
Operation Display messages SAFETY BELT message DANGER Risk of fatal injury in the event of falling from the truck if it tips over! If the truck tips over, the driver is at risk of injury even if a restraint system is used.
Page 279
Operation Display messages DANGER Risk of accident! – The speed must be adjusted to suit the driving situation! The increased safety provided by this function must not be misused in order to take safety risks. ARE YOU SURE ? message If the message appears on ARE YOU SURE ?
Page 280
Operation Display messages The seat switch is not actuated while the ac- celerator pedal or steering wheel is actuated The accelerator pedal or the steering wheel is actuated, even though no one is sitting in the driver’s seat. The message SEAT SWITCH appears on the display.
Page 281
Operation Display messages The shift time has been exceeded NOTE The shift time is adjustable. If the key switch is switched on and the driver does not leave the seat before the set shift time is exceeded, appears SEAT SWITCH on the display.
Page 282: Drive-Specific Messages

Operation Display messages SURVEILLANCE message If the message appears SURVEILLANCE in the display, there is a fault in the process monitoring. This shuts off the drive unit. – Switch the key switch to the «0» position and then back to the «I» position. –…
Page 283
Operation Display messages NOTE If the EXH.GAS PURIFIER message ap- pears during regeneration, a fault has occur- red. Notify the authorised service centre • EXH.GAS PURIFIER PLEASE WAIT message If the EXH.GAS PURIFIER PLEASE WAIT message appears on the display, the particle ﬁlter is being regenerated.
Page 284
Operation Display messages ADBLUE FILLING LEVEL message ® If the ﬁlling level of the AdBlue tank has fallen signiﬁcantly, the ADBLUE FILLING LEVEL message appears on the display-operating unit. ® If an AdBlue ﬁlling level of 2 litres is reached, the driving speed is limited to 5 km/h.
Page 285
Operation Display messages ® – Top up the AdBlue ASH LOAD message If the message appears on the ASH LOAD display, the particle ﬁlter has become clogged with ash. Repair must be performed by the authorised service centre. – Notify the authorised service centre. GLOW message If the message appears in the display,…
Page 286
Operation Display messages FUEL FILTER message The fuel ﬁlter is equipped with a level indicator that reports water aggregation in the fuel ﬁlter on the display and operating unit. If the message appears in the FUEL FILTER display, the fuel ﬁlter is saturated with water. This water must be drained.
Page 287
60 seconds, there is an error. Initially, the truck can still be operated. The error message is shown on the display and operating unit until the error has been rectiﬁed by the authorised service centre.
Page 288
Operation Display messages generation is complete. The truck is ready for operation again. SCR-SYSTEM SERVICE message If the message SCR-SYSTEM SERVICE appears on the display, there is a fault in the SCR exhaust gas treatment system. – Notify the authorised service centre. SCR-SYSTEM MALFUNCTION mes- sage If the message…
Page 289: Refuelling

Operation Refuelling – Perform parked regeneration. START IC ENGINE message If the message appears START IC ENGINE on the display, the internal combustion engine of the truck can be started. – Start the engine. Refuelling Diesel fuel — Speciﬁcations CAUTION Risk of component damage if non-approved fuels are used! Use only approved fuels with the following speciﬁ-…
Page 290
Operation Refuelling The following is not permitted: • Admixtures of petroleum, kerosene or additional ﬂuidity additives • Distillate fuels for marine engines • Jet fuels • Biodiesel fuels • US fuels in line with the ASTM D 975 1-D S500 or ASTM D 975 2-D S500 stan- dards –…
Page 291
Operation Refuelling due to high corrosion and signiﬁcant lifetime reduction of the engine. Winter operation with diesel fuel CAUTION Adding petrol can lead to malfunctions in the fuel injection system! – Do not add petrol. – Do not add petroleum, kerosene or additional ﬂuidity additives.
Page 292: Filling Up With Diesel Fuel

Operation Refuelling Filling up with diesel fuel CAUTION Lack of fuel can cause malfunctions! If the fuel tank has been run empty, the fuel injection system can draw in air bubbles. These air bubbles can lead to malfunctions in the fuel injection system. If the fuel tank has been replaced during repair work or has been run empty, diesel fuel must be pre-pumped with the fuel hand pump after ﬁlling;…
Page 293: Using The Fuel Hand Pump

Operation Refuelling The ﬁller neck (1) for the fuel tank is located on the front right in the drive direction, on the mudguard of the front wheel. – Turn the locking cap (2) at the ﬁller neck to the left and remove. –…
Page 294
Operation Refuelling – Open the service ﬂap (1) on the right. 7341_003-024_V2 – To pump, pull the fuel hand pump (1) out and push it in again ten times. NOTE A light hissing sound you may hear indicates that the fuel is ﬂowing and is not a fault on the truck.
Page 295: Topping Up Adblue

Operation Refuelling Topping up AdBlue The AdBlue ﬁller neck (1) is located on the front right of the truck. It is recommended that the AdBlue tank be reﬁlled with AdBlue every time the diesel fuel is topped up. – Turn the locking cap (2) of the AdBlue ﬁller neck to the left and remove.
Page 296: Cleaning

Operation Cleaning Cleaning Cleaning the truck WARNING Risk of injury from falling off the truck! When climbing onto the truck, there is a risk of getting stuck or slipping and falling. Use suitable equipment to reach higher points on the truck. –…
Page 297
Operation Cleaning CAUTION Abrasive cleaning materials can damage the surfa- ces of components! Using abrasive cleaning materials that are unsuita- ble for plastics can cause plastic parts to dissolve or become brittle. The screen on the display-opera- ting unit could become cloudy. –…
Page 298: Cleaning The Electrical System

Operation Cleaning Cleaning the electrical system CAUTION Cleaning electrical system parts with water can damage the electrical system. – Cleaning electrical system parts with water is forbidden! – Use dry cleaning materials in ac- cordance with the manufacturer’s speciﬁcations. – Do not remove covers etc. –…
Page 299: Cleaning The Windows

Operation Cleaning ENVIRONMENT NOTE Dispose of any ﬂuid that has been spilled or collected in the collection vessel in an environmentally friendly manner. Follow the statutory regulations. Cleaning the windows Any panes of glass, e.g. cab windows (vari- ant), must always be kept clean and free of ice. This is the only means of guaranteeing good visibility.
Page 300: Procedure In Emergencies

Operation Procedure in emergencies Procedure in emergencies Emergency shutdown NOTE Only trucks with a joystick 4Plus (variant) are equipped with an emergency off switch (1). WARNING No electric braking assistance is available when the emergency off switch is actuated! Actuating the emergency off switch will de-energise the drive unit.
Page 301: Procedure If Truck Tips Over

Operation Procedure in emergencies ing) does not function. The truck must be decelerated with the mechanical brake by pressing the brake pedal • No hydraulic functions are available – Press the emergency off switch (1). The truck will roll to a stop in drive mode. –…
Page 302: Emergency Hammer

Operation Procedure in emergencies – Bend your body against the direction of the fall. Emergency hammer The emergency hammer is used to rescue the driver if he is shut inside the cab in a hazardous situation, for example if the truck has toppled over and the cab door cannot be opened.
Page 303
Operation Procedure in emergencies WARNING The load is lowered! The lowering speed is regulated by unscrewing the emergency lowering screw. – Note the following list. Remember the following: • Tightening torque: max. 2.5 Nm • When unscrewed a little: The load lowers slowly •…
Page 304
Operation Procedure in emergencies – Remove the rubber edging strip (3) from the valve chamber cover (1). – Unscrew the screws (2) from the valve chamber cover. – Lift off the valve chamber cover and place in a safe location. –…
Page 305: Releasing The Spring-Operated Brake

However, the truck can still be moved until the drive wheel units are blocked. In order to tow the truck, the spring-operated brake must be released by actuating the brake valve.
Page 306
Operation Procedure in emergencies Actuate the brake valve by means of a cou- pling pin: – Take the coupling pin out of the counter- weight. – Grip the rubber tab in the rubber mat using the ﬁnger opening and pull up the tab. 6341_003-034 –…
Page 307: Disconnecting And Connecting The Battery

If the bottom plate is not inserted, there is a danger of shoes getting stuck, causing you to fall. Even when the bottom plate is installed, there is still a danger of slipping and injury if the rubber mat is not used.
Page 308: Jump-Starting

Operation Procedure in emergencies Jump-starting NOTE A 12-V power source (e.g. second forklift truck of the same type) must be available. WARNING Risk of short circuit if the jump leads are connected or disconnected in the incorrect order! If the batteries’ negative terminals are connected to the negative cable, both bodies are also conducti- vely connected to one another.
Page 309: Towing

Operation Procedure in emergencies – Disconnect the negative cable from the negative terminal on the current-giving battery. – Disconnect the positive cable (2) from the positive terminal on the discharged battery. – Disconnect the positive cable from the positive terminal on the current-giving battery.
Page 310
Operation Procedure in emergencies DANGER While manoeuvring, there is a risk of fatal injury in the area between the truck and the towing vehicle! Inform the driver of the towing vehicle and the mechanic attaching the tow bar about the risks. When you ﬁt the tow bar, always use a second person to guide the towing vehicle manoeuvres.
Page 311
Operation Procedure in emergencies – Apply the parking brake. – Switch off the key switch. – Check the pulling and braking forces of the towing vehicle. – With a second person as a guide, manoeu- vre the towing vehicle to the truck. –…
Page 312: Transporting The Truck

Operation Transporting the truck Transporting the truck Transport CAUTION Risk of material damage from overloading! If the truck is driven onto a means of transport, the load capacity of the means of transport, the ramps and the loading bridges must be greater than the actual total weight of the truck.
Page 313
Operation Transporting the truck DANGER Risk of accident from the truck crashing! Steering movements can cause the tail end to veer off the loading bridge towards the edge. This may cause the truck to crash – Before driving across a loading bridge, ensure that the loading bridge is properly attached and secured.
Page 314: Crane Loading

Operation Transporting the truck – Attach the harness (1) to each side of the truck. – Lash the truck towards the rear. – Attach the harness (1) to the coupling pin (2) or loop the harness around the coupling pin. –…
Page 315
Operation Transporting the truck Determining the loading weight – Park the truck securely; see chapter «Park- ing the truck securely». – Determine the unit weights by reading them off the truck nameplate and, if necessary, Type-Modèle-Typ / Serial no.-No. de série-Serien-Nr. / year-année-Baujahr the attachment (variant) nameplate.
Page 316
Operation Transporting the truck – Loop the lifting straps around the main traverse (3) on the outer mast of the lift mast as shown. – Loop the lifting straps around the counter- weight (4) as shown. – Determine the truck’s centre of gravity, see «Dimensions»…
Page 317
Operation Transporting the truck – Adjust the length of the harnesses so that the lifting eye (6) is vertically above the truck’s centre of gravity. This ensures that the truck hangs level when lifted. – Attach the lifting straps to the lifting eye and insert the safety device (5).
Page 318: Shutdown

Operation Shutdown Shutdown Shutting down and storing the truck CAUTION Component damage due to incorrect storage! If the truck is stored or shut down incorrectly for more than two months, it may suffer corrosion da- mage. If the truck is parked in an ambient tempera- ture of less than –10°C for an extended period, the battery will cool down.
Page 319: Recommissioning After Decommissioning

Operation Shutdown – To relieve the strain on the load chains, lower the fork onto a suitable supporting surface, e.g. a pallet. – Check the hydraulic oil level and top up if required. – Apply oil or grease thinly to all uninsulated moving parts.
Page 320
Operation Shutdown – Restore engine to normal condition accord- ing to regulations of engine manufacturer. – Check the engine oil for condensation water and replace the oil if necessary. – Check hydraulic oil for condensation water; change if necessary. – Have the same checks and tasks carried out by the authorised service centre that were carried out before initial commissioning.
Page 321: Maintenance

Maintenance…
Page 322: Safety Regulations For Maintenance

Maintenance Safety regulations for maintenance Safety regulations for maintenance General information DANGER Risk of fatal poisoning! It is dangerous to leave the engine running in enclosed spaces. The engine consumes oxygen and emits carbon dioxide, carbon monoxide and other poisonous gases. There is a risk of fatal poisoning! –…
Page 323: Working On The Electrical Equipment

Maintenance Safety regulations for maintenance Working on the electrical equipment Work may only be performed on the electrical equipment of the truck when it is in a voltage- free state. Function checks, inspections and adjustments on energised parts must only be performed by trained and authorised persons, taking the necessary precautions into account.
Page 324: Safety Devices

Maintenance Safety regulations for maintenance Safety devices After maintenance and repair work, all safety devices must be reinstalled and tested for operational reliability. Set values The device-dependent set values must be observed when making repairs and when changing hydraulic and electrical compo- nents.
Page 325
Maintenance Safety regulations for maintenance CAUTION Possibility of damage to the ceiling! – Note the maximum lift height of the lift mast. Securing the lift mast against tilting backwards A hardwood beam with a cross-section of 120 x 120 mm is required. The length of the hardwood beam must approximately correspond to the width of the fork carriage (b3).
Page 326: General Maintenance Information

Maintenance General maintenance information General maintenance information Personnel qualiﬁcations Only qualiﬁed and authorised personnel are allowed to perform maintenance work. Reg- ular safety checks and checks after unusual incidents must be performed by a competent person. The competent person must conduct their evaluation and assessment from a safety standpoint, unaffected by operational and economic conditions.
Page 327
Maintenance General maintenance information Maintenance timeframe – Carry out maintenance work on the truck in accordance with the «Service in» display (1). – The maintenance check lists indicate the maintenance work that is due. The intervals are deﬁned for standard use. Shorter maintenance intervals can be deﬁned in consultation with the operating company, depending on the application conditions of the…
Page 328
Maintenance General maintenance information 57348011800 EN — 11/2018…
Page 329: Maintenance — 500 Hours

Maintenance General maintenance information Maintenance — 500 hours At operating hours Carried out 1000 1500 2000 2500   Note 500-hour maintenance is performed by the operating company itself. Exhaust system Deutz TCD 4.1-ﬁnal: Change the main ﬁlter of the feed pump. 57348011800 EN — 11/2018…
Page 330
Maintenance General maintenance information 57348011800 EN — 11/2018…
Page 331: Maintenance — 1000 Hours/Annually

Maintenance General maintenance information Maintenance — 1000 hours/annually At operating hours 1000 2000 4000 5000 7000 Carried out 8000 10000 11000 13000 14000   Chassis, bodywork and ﬁttings Check chassis for cracks Check overhead guard/cab and panes of glass for damage Check controls, switches and joints for damage, and apply grease and oil Check driver’s seat for correct function and for damage Check driver restraint system for correct function and for damage, and clean.
Page 332
Maintenance General maintenance information At operating hours 1000 2000 4000 5000 7000 Carried out 8000 10000 11000 13000 14000   Replace fuel ﬁlter (main ﬁlter) Steering Check steering system for correct function and for leaks Check that the steering wheel is ﬁrmly attached and check the turning handle for damage Steering axle: Check that it is ﬁrmly attached, check for leaks, and apply grease Check steering stop…
Page 333
Maintenance General maintenance information At operating hours 1000 2000 4000 5000 7000 Carried out 8000 10000 11000 13000 14000   Check the play between the fork carriage stop and run-out barrier Check tilt cylinders and connections for damage and leaks Check fork carriage for damage and wear Check fork arm interlock for damage and correct function Check fork arms for wear and deformation…
Page 334
Maintenance General maintenance information 57348011800 EN — 11/2018…
Page 335: Maintenance — 3000 Hours/Every Two Years

Maintenance General maintenance information Maintenance — 3000 hours/every two years At operating hours Carried out 3000 6000 9000 12000 15000   Note Perform all 1000-hour maintenance work. Power unit Change the gearbox oil Replace the bleeder screws on the drive wheel units Internal combustion engine Replace the V-belt and tensioning pulleys (every 2 years) Replace the safety cartridge in the air ﬁlter…
Page 336: Quality And Quantity Of The Required Operating Materials

Maintenance General maintenance information spare parts shall assume unlimited liability in the event of damage or harm. Quality and quantity of the required operating materials Only the operating materials speciﬁed in the maintenance data table may be used. – The required consumables and lubricants can be found in the maintenance data table.
Page 337: Lubrication Plan

Maintenance General maintenance information Lubrication plan Lubrication point Code Four lubricating nipples on each side of the steering axle for the axle stub bearing and track rod bearings Sliding surfaces on the lift mast Load chains One lubricating nipple on each of the two lift mast bearings The respective lubricant speciﬁcation can be found in the «Maintenance data table»…
Page 338: Maintenance Data Table

Maintenance General maintenance information Maintenance data table General lubrication points Operating material Speciﬁcations Code Unit Dimensions Lubrication High-pressure ID no. 0147873 As required grease Controls/joints Operating material Speciﬁcations Unit Dimensions Code Lubrication High-pressure ID no. 0147873 As required grease SAE 80 As required MIL-L2105 API-GL4…
Page 339
Maintenance General maintenance information Tyres Operating material Speciﬁcations Code Unit Dimensions Wear limit To wear mark Superelastic tyres Minimum tread depth 1.6 mm Pneumatic tyres Air pressure See information on truck Minimum tread depth 1.6 mm Steering axle Operating material Speciﬁcations Code Unit…
Page 340
Maintenance General maintenance information Operating material Speciﬁcations Code Unit Dimensions Torque wrench Screws for the lift Cylinder head For further mast bearing bolt M24x90-12.9 information, refer ISO 4762 to the workshop manual for the truck in question. Lift mast bearing Grease Aralub 4320 Fill with grease until a…
Page 341: Providing Access To Maintenance Points

Maintenance Providing access to maintenance points Air ﬁlter system Operating material Speciﬁcations Code Unit Dimensions Filter cartridge and Air ﬁlter safety cartridge Oil-bath air ﬁlter Engine oil DQC III-10 LA, Level mark on the DQC IV-10 LA oil tank Washer system Operating material Speciﬁcations Code…
Page 342
Maintenance Providing access to maintenance points – Move the steering column (1) as far for- wards as possible and secure; see section entitled «Adjusting the steering column». – Slide the driver’s seat (2) all the way for- ward; see section entitled «Adjusting the MSG 65/MSG 75 driver’s seat».
Page 343: Closing The Bonnet

Maintenance Providing access to maintenance points – If the gas spring is equipped with a position lock (variant), open the bonnet until the latch (1) of the gas spring (2) snaps into place. WARNING Risk of injury from the bonnet lowering! The bonnet is ﬁtted with a gas spring that holds the bonnet in the open position.
Page 344
Maintenance Providing access to maintenance points Releasing the position lock (variant) – Press the latch (1) at the mark and PRESS lower the bonnet slightly. – Release the latch. Closing the bonnet – Holding it by the handle, pull down the bonnet until the lock audibly engages.
Page 345: Removing And Attachingthe Left Side Cover

Maintenance Providing access to maintenance points Removing and attaching the left side cover Removing the cover – Release the quick release clamps (1) with a 1/4 revolution. – Remove the cover (2) and put carefully aside. Attaching the cover – Carefully position the cover (2). –…
Page 346
Maintenance Providing access to maintenance points The connecting plug for the accelerator is located underneath the bottom plate. – Open the bonnet. – Remove the rubber mat. – Grasp the recess (3) in the bottom plate (2). – Raise the bottom plate slightly. –…
Page 347: Opening And Closing The Right-Hand Service Flap

Maintenance Providing access to maintenance points – Position the bottom plate at the front. – Carefully guide the bottom plate down and close. – Insert the rubber mat. – Close the bonnet. Opening and closing the right-hand service ﬂap Opening the service ﬂap NOTE Cold weather and ageing can also reduce the performance of the gas springs and cause the…
Page 348: Remaining Ready For Operation

Maintenance Remaining ready for operation – Make sure that the safety hook (1) engages in the gap of the holder (2). Closing the service ﬂap CAUTION Limbs can become trapped when closing the service ﬂap — risk of crushing! When you close the service ﬂap, there must be nothing between the service ﬂap and the edge of the frame.
Page 349
Maintenance Remaining ready for operation – Stand on the bottom plate of the driver’s cab and turn your body slightly to the left as shown. 7341_003-065 – Using both hands, pull out the oil dipstick (1) and wipe it using a cloth. 7341_003-066 57348011800 EN — 11/2018…
Page 350
Maintenance Remaining ready for operation – Insert the oil dipstick (1) as far as it will go and pull it out again. The oil level must be between the marks (arrows). CAUTION Risk of engine damage! Insufﬁcient engine lubrication can cause engine damage.
Page 351: Cleaning The Dust Valve

Maintenance Remaining ready for operation Cleaning the dust valve – Press the dust valve (1) on the air ﬁlter housing between your ﬁngers until no more dust is emitted. 7311_120-004 Filling the washer system CAUTION Components may become damaged due to the effects of frost! Water expands when it freezes.
Page 352: Checking The Pre-Cleaner

Maintenance Remaining ready for operation Checking the pre-cleaner The pre-cleaner is part of the «heavy dust guard» equipment variant and is mounted at the rear of the truck. In the pre-cleaner, coarse dust and dirt are removed from the intake air. Checking the pre-cleaner –…
Page 353: Checking The Cooling Fluid Level

Maintenance Remaining ready for operation – Remove the oil tank from the housing (1). – Check the dirt level in the oil tank. The oil tank must be cleaned if the deposited dirt reaches approximately halfway up to the oil level; see the «Cleaning the oil bath ﬁlter» chapter.
Page 354
Maintenance Remaining ready for operation – Slowly open the ﬁller cap (1) of the coolant tank (2) and release the excess pressure. – Unscrew further and remove the ﬁller cap. 7341_003-050 – Check the level of the coolant. The cam (3) in the coolant tank must be ﬂushed.
Page 355: Topping Up The Cooling Fluid And Checking The Coolant Concentration

Maintenance Remaining ready for operation Topping up the cooling ﬂuid and checking the coolant concentration WARNING Risk of scalding due to hot cooling ﬂuid! The cooling system is pressurised! Coolant may escape if the coolant tank (2) is opened while the engine is hot.
Page 356
Maintenance Remaining ready for operation – Slowly open the ﬁller cap (1) of the coolant tank (2) and release the excess pressure. – Unscrew further and remove the ﬁller cap. – Check the concentration of the coolant. Concentration of the coolant CAUTION Coolant with a different speciﬁcation must not be mixed in!
Page 357
Maintenance Remaining ready for operation – Check the level of the coolant. The cam (3) in the coolant tank must be ﬂushed. – Top up the coolant if necessary. – Screw the ﬁller cap (1) back on tightly. – Check the cooling system for leaks; refer to the section entitled «Cleaning the radiator and checking for leaks».
Page 358: Cleaning The Radiator And Checking For Leaks

Maintenance Remaining ready for operation Cleaning the radiator and checking for leaks WARNING Risk of burns due to hot components! Components on the engine (e.g. engine block, radiator, etc.) can be so hot that direct contact can burn the skin and can burn or singe materials. –…
Page 359: Draining Water From The Fuel Filter

Maintenance Remaining ready for operation – Perform a visual inspection of the radiator from the rear of the truck. – If necessary, unscrew the screw joints (2) for the radiator grille and dismantle it to clean the radiator behind. – Clean the radiator grille (1). –…
Page 360
Maintenance Remaining ready for operation – Cover the area beneath the fuel ﬁlter (1) carefully with a cleaning cloth. CAUTION Risk of ﬁre! The heat protection sleeve (5) of the exhaust gas system must not be polluted with diesel fuel. If diesel fuel penetrates the material of the heat protection sleeve, this can lead to the sleeve and surrounding components catching ﬁre.
Page 361: Cleaning The Pre-Cleaner

Maintenance Remaining ready for operation Cleaning the pre-cleaner – Loosen clamp (1) on pre-cleaner. – Remove housing cover (2). – Remove and empty dust container (3). – Clean coarse contamination from lower part of container (4). – Re-attach dust container and secure with clamp.
Page 362: Replacing The Air Filter Cartridges

Maintenance Remaining ready for operation – Carefully install the oil tank and engage the four clamps (2) on the housing (1). Replacing the air ﬁlter cartridges NOTE The air ﬁlter cartridges must be changed if the AIR FILTER message appears on the display and operating unit, or at least every 3000 hours or every two years.
Page 363
Maintenance Remaining ready for operation – Remove the ﬁlter cartridge (3). CAUTION Risk of engine damage! The safety cartridge must remain in the air ﬁlter housing until all residual dirt has been removed from the housing so that no dirt enters the intake system! –…
Page 364: Changing The Heating System Fresh Air Filter

Maintenance Remaining ready for operation – Reﬁt the air ﬁlter cover (5) with the mark (6) facing upwards – Engage the clamps (7) on the air ﬁlter. – Close the bonnet. 7321_003-078 Changing the heating system fresh air ﬁlter The fresh air ﬁlter for the heating system is on the right on the exterior of the cab.
Page 365: Lubricating The Joints And Controls

Maintenance Remaining ready for operation – Grasp the ﬁlter insert (3) at the ﬁnger opening (4) and remove it completely from the ﬁlter housing. – Check the ﬁlter insert for contamination and beat out. NOTE Replace the ﬁlter insert when it is clearly grey, but at least every two months.
Page 366: Maintaining The Seat Belt

Maintenance Remaining ready for operation Maintaining the seat belt DANGER There is a risk to life if the seat belt fails during an accident! If the seat belt is faulty, it may tear or open during an accident and no longer keep the driver in the driver’s seat.
Page 367
Maintenance Remaining ready for operation – Check the buckle (1) for proper locking. When the belt tongue (2) is inserted, the seat belt must be held securely. The belt tongue (2) must release when the red button (4) is pressed. –…
Page 368: Checking The Driver’s Seat

Maintenance Remaining ready for operation Checking the driver’s seat WARNING Risk of injury! – After an accident, check the driver’s seat with attached restraining belt and fastening. – Check the controls for correct operation. – Check the condition of the seat (e.g. wear on the upholstery) and secure fastening to the hood.
Page 369: Servicing Wheels And Tyres

Maintenance Remaining ready for operation – Re-insert the ﬁlter mat into the ﬁlter housing. – Make sure that the ﬁlter mat sits correctly and accurately in the ﬁlter housing. – Attach the heating system panelling and secure tightly in place using the screws. Servicing wheels and tyres WARNING Risk of accident!
Page 370
Maintenance Remaining ready for operation Checking condition and wear of the tyres Superelastic tyres (variant) – Check the remaining distance between the tyre tread and the (60 J) wear mark. Super-elastic tyres (variant) can be worn down to the (60 J) wear mark. –…
Page 371: Replacing The Fuses

Maintenance Remaining ready for operation Checking the air pressure NOTE The correct air pressure for pneumatic tyres (variant) is determined by the type of tyre used. The air pressure measured must correspond to the manufacturer’s information. – Observe the air pressure value indicated on the adhesive label (1) on the truck.
Page 372: Checking The Hydraulic Oil Level

Maintenance Remaining ready for operation – Open the cover fastenings (1) and remove the cover. – Change the defective fuse. – Close the bonnet. 7311_003-021 Checking the hydraulic oil level CAUTION Hydraulic oils are hazardous to health and are pressurised during operation. –…
Page 373
Maintenance Remaining ready for operation The lower mark, (1) or (2), indicates the minimum ﬁlling level. The top mark, (max), indicates the maximum ﬁlling quantity. The lower mark that is applicable for the speciﬁc truck depends on the lift mast, the relevant lift height (see table below) and the resulting ﬁlling quantities.
Page 374: Checking The Hydraulic System For Leak Tightness

Maintenance Remaining ready for operation WARNING If the hydraulic oil level is too high, it can lead to inadmissibly high pressure and damage to the hydraulic system. – If the oil level is higher than the top (max) mark, lower the hydraulic oil level. –…
Page 375: Lubricating The Lift Mast And Roller Track

Maintenance Remaining ready for operation Replace pipes if they display the following abnormalities: • Abrasion • Deformation and bending • Leaking Lubricating the lift mast and roller track – Remove dirt and lubricant residue from the roller track. – Lubricate the roller tracks (1) of the outside, middle, and inside mast with a super- pressure adhesion lubricant to reduce wear.
Page 376
Maintenance Remaining ready for operation Model RO*243 – Pull out the safety handle (3). – Push the hand lever (2) upwards. – Grease using the lubricating nipple(1) in accordance with the maintenance data table; see ⇒ Chapter «Maintenance data table», P. 5-326. –…
Page 377
Maintenance Remaining ready for operation Model RO*245 – Lubricate via the points provided for this purpose (lubricating nipple, opened cou- pling) in accordance with the maintenance data table; see ⇒ Chapter «Maintenance data table», P. 5-326. – Grease the supporting surface for the tow-bar eye.
Page 378
Maintenance Remaining ready for operation 57348011800 EN — 11/2018…
Page 379: 1000-Hour Maintenance/Annual Maintenance

1000-hour maintenance/annual mainte- nance…
Page 380: Other Tasks

1000-hour maintenance/annual maintenance Other tasks Other tasks – Perform all tasks required to maintain full operability; see the chapter entitled «Remaining ready for operation». Checking the exhaust gas system – Inspect the exhaust gas system for external damage, secure ﬁt, and leaks. Checking the lift cylinders and the hydraulic connections for leak tightness…
Page 381: Checking The Fork Arms

1000-hour maintenance/annual maintenance Checking the fork arms Checking the fork arms CAUTION Fork arms must not be uneven! – Always replace both fork arms. – Check the fork arms (1) for visible deforma- tion and excessive wear. No cracks or deformations must be visible on the fork arms in the area around the fork bend.
Page 382
1000-hour maintenance/annual maintenance Checking the reversible fork arms 57348011800 EN — 11/2018…
Page 383: Technical Data

Technical data…
Page 384: Dimensions

Technical data Dimensions Dimensions Seat is adjustable ± 90 mm Fork spacing is adjustable 57348011800 EN — 11/2018…
Page 385
Technical data Dimensions NOTE Measurements h and b customer-speciﬁc and can be taken from the order conﬁrmation. Centre of gravity «S» (distance measured from the front axle) RX70-60 1036 mm RX70-70 1036 mm RX70-80 1036 mm RX70-80 (LSP 900) 1036 mm NOTE The speciﬁed centre of gravity «S»…
Page 386: Vdi Datasheet

Different tyres, lift masts, additio- nal units etc. may produce different values. Key data RX70-80 RX70-60 RX70-70 RX70-80 (LSP 900) Manufacturer STILL GmbH STILL GmbH STILL GmbH STILL GmbH Diesel en- Diesel en- Diesel en- Diesel en- Drive gine/electric gine/electric gine/electric…
Page 387
Technical data VDI datasheet RX70-80 RX70-60 RX70-70 RX70-80 (LSP 900) Number of front wheels (x = driven) Number of rear wheels (x = driven) b 10 Front track width, single tyre 1306 1510 1510 1561 (mm) b 11 Rear track width 1358 1358 1358…
Page 388
Technical data VDI datasheet RX70-80 RX70-60 RX70-70 RX70-80 (LSP 900) Ground clearance at the m2 (mm) 210 centre of the wheelbase Aisle width for pallets 1000 x Ast (mm) 4907 4987 5056 5185 1200 crosswise Aisle width for pallets 800 x Ast (mm) 5107 5187 5256…
Page 389
Technical data VDI datasheet Engine RX70-80 RX70-60 RX70-70 RX70-80 (LSP 900) Deutz/ Deutz/ Deutz/ Deutz/ Engine manufacturer/model TCD 4.1 l TCD 4.1 l TCD 4.1 l TCD 4.1 l Engine power rating in accordance with ISO 1585 Nominal speed 2400 2400 2400 2400…
Page 390: Ergonomic Dimensions

Technical data Ergonomic dimensions Ergonomic dimensions 40 mm WARNING Danger of impact injuries to the head! If the head of the operator is located too close to the underside of the roof, the suspension of the driver’s seat or an accident may cause the head to strike the overhead guard.
Page 391
Technical data Ergonomic dimensions 57348011800 EN — 11/2018…
Page 392: Fuse Assignment

Technical data Fuse assignment Fuse assignment 1F08 12-V battery (permanent positive), 10 A 1F19 12 V for engine control unit (ECU), 10 A Switch lock, terminal 30, 10 A Exhaust gas recirculation, 10 A 1F09 1F21 1F10 Butterﬂy valve for exhaust gas, 10 A 1F22 sensors, 15 A 1F11…
Page 393
Technical data Fuse assignment Additional fuses 9F10 9F11 Depending on the truck equipment, additional fuses are located on a fuse holder to the right of the fuse box. 9F10 Air conditioning (variant), compressor / condenser, 20 A 9F11 Air conditioning (variant), evaporator, 20 A 57348011800 EN — 11/2018…
Page 394
Technical data Fuse assignment 57348011800 EN — 11/2018…
Page 395
Index NUMBERS AND SYMBOLS Attachments Controlling using a double 12-V socket ….. 230 mini-lever ….196 Controlling using the double mini-lever and the 5th function .
Page 396
Index Blue-Q Clipboard ….. . . 244 Conﬁgure ….118 Closing the bonnet .
Page 397
Index Diesel fuel ….. . . 52 Drivers ……29 Filling up .
Page 398
Index Fork arms Insurance cover on company premises . . 31 Length ….. . . 37 Interior lighting ….239 Fork extension .
Page 399
Engine ….. . 328 STILL SafetyLight ….224 Exhaust gas treatment (SCR) .
Page 400
Index EMERGENCY SWITCH ..264 MSG 65/MSG 75 driver’s seat EMPTY ….. . 274 Adjusting .
Page 401
Index Parked regeneration Resetting the daily operating hours ..117 Interruption ….184 Residual dangers ….38 Performing .
Page 402
Index Selecting the drive direction ..128 Selecting the driver PIN … . 102 Technical data Set values ….. . 312 Dimensions .
Page 403
Index Variants Visual inspection Access authorisation with PIN code . . 97 Oil bath air ﬁlter ….340 Automatic lift cut out … . 145 Pre-cleaner .
Page 406
STILL GmbH 57348011800 EN – 11/2018…

Источник

Still Forklifts: owner’s, service and maintenance manuals, error codes list, DTC, spare parts manuals & catalogues, wiring diagrams, schematics free download PDF

Title	File Size	Download LInks
Still 0303, 0305, 0323, 0324, 0325, 0326, 0327, 0328, 0329, 0330, 0331, 0332, 0333, 0334, 0335, 0336, 0337, 0338, 0339, 0340 Original Instructions Manual [PDF]	16.1Mb	Download
STILL 7032-34 / 38-40 / 48-50 Technical Data for Maintenance Service [PDF]	5.8Mb	Download
Still Electric Forklift R20-15 R20-16 R20-18 R20-20 Service Manual [PDF]	21.2Mb	Download
Still Electric Forklift RX20-15-20, RX60-16-20 Workshop Manual [PDF]	24.5Mb	Download
STILL Electric pallet truck Original instructions [PDF]	2.5Mb	Download
STILL EXD 20 Manual [PDF]	2.9Mb	Download
Still EXP 14, EXP 16, EXP 20, EXP 14D, EXP 16D, EXP 20D, EXP-SF 14D, EXP-SF 16D, EXP-SF 20D, 0301 Original Instructions Manual [PDF]	16.1Mb	Download
Still EXV 14, EXV 16, EXV 20, EXV 14I, EXV 16I, EXV 20I, EXV-SF 14, EXV-SF 16, EXV-SF 20, EXV-SF 14I, EXV-SF 16I, EXV-SF 20I Original Instructions Manual [PDF]	16.1Mb	Download
STILL FM Type 447 Workshop Manual [PDF]	2Mb	Download
STILL Forklift Fault Codes [PDF]	2.3Mb	Download

Still Forklift R60-25 Manual [PDF]	10.5Mb	Download
Still GX10 Operating and Maintenance Instructions Manual [PDF]	2.1Mb	Download
Still GX10, OPX 25, OPX 20 PLUS, OPX 25 PLUS, OPX-L 12, OPX-L 16, OPX-L 20, OPX-L 20 S, OPX-D 20, LTX 50 Operating and Maintenance Instructions Manual [PDF]	19.5Mb	Download
STILL iGo neo CX20 Original instructions [PDF]	3.8Mb	Download
STILL M15 / M15T System Diagnosis & Workshop Manual [PDF]	31.8Mb	Download
Still R50-10, 12 / 16 Workshop Service Manual [PDF]	7.9Mb	Download
STILL R60-20-22-25-30-35-40-45-50 Workshop Manual [PDF]	10.5Mb	Download
Still R70-40-45-50 Diesel Forklift Operating Instructions [PDF]	5.5Mb	Download
Still R70-40T, R70-45T, R70-50T Operating Instructions [PDF]	6.2Mb	Download
Still RCD40 Original Instructions [PDF]	20.4Mb	Download
STILL Reach Truck Control Unit RCU Error Code List [PDF]	2.3Mb	Download
Still RX20, RX20-14C, RX20-16C, RX20-16, RX20-16L, RX20-18, RX20-18L, RX20-20L, RX20-16P, RX20-16PL, RX20-18P, RX20-18PL, RX20-20P, RX20-20PL, 6219 Series Original Instructions [PDF]	13.5Mb	Download
Still RX50-10-13-15-16T Parts Catalogue [PDF]	3.7Mb	Download
STILL RX50-10, RX50-13, RX50-15, RX50-16 Manual [PDF]	8.8Mb	Download
STILL RX60-60,RX60-70, RX60-80, RX60-80 / 900 Electric truck Original instructions [PDF]	11.3Mb	Download
STILL RX70 / 40 / 50 LPG Trucks Manual [PDF]	10.9Mb	Download
STILL Service Brochure [PDF]	1.9Mb	Download

Still Forklift Manuals PDF

Hans Still established a workshop in 1920 where he serviced electric motors and created semi-automatic tools for generating electricity in emergencies. He continued to see dependability, efficiency, and individual perfectionism as the fundamentals of labor, and therefore he soon rose to renown and success in Hamburg.

Still started off as a maker of storage equipment in 1945. The German market received the introduction of the electric forklift EK 2000 with a 2-ton lifting capability. The product developed a reputation during the following two years. The German Federal Railways placed a significant order with Still for EK 2000s in 1947.

A tricycle tractor (still called Muli-Mobil) was introduced a year later. The EGS 1000, the first forklift, entered production in 1949.

The year 1952 proved devastating for the business since founder Hans Still passed away in an automobile accident. The management, however, opted to keep up with the activities. Up to 1964, efforts were made to upgrade and enlarge the Still. New assembly facilities, an office complex, and a thermal power plant all started operating at this time. The firm expanded internationally after strengthening its position in the German market during the following 20 years.

Hamburg is where Still’s primary manufacturing facility is now. Additionally, manufacturers may be found in France, Italy, China, Brazil, and the German cities of Geise and Reutlingen.

The business was honored by the International Forklift Manufacturers Association in 2008. (FLTA – ForkLift Truck Association). Unmanned warehouse technology has been actively explored since 2015.

2019 saw Still win the coveted IFOY Award for the LTX 50 automated tractor and LiftRoller iGo with autonomous loading and unloading capabilities in the Unmanned Vehicles and Intralogistics Robots category. The machines were some of the first in the world to be able to move loads weighing up to 1.2 tons without an operator.

Over 200 nations get loaders, reach trucks, stackers, and other devices under the Still name. Production involves more than 9000 workers. The company has 200 distribution outlets, 14 branches in Germany, and 20 subsidiaries. The firm fully satisfies the demands of major industrialists, people who use transportation services, and small- and medium-sized businesses.

Range of STILL forklifts

According to the kind of motor they use—diesel, gasoline, or electric—forklifts are still split into three categories. RC 40 (load capacity up to 3 tons), RX 70 (up to 5 tons), and R 70 are among the first three classes (up to 8 tons). The equipment is moving at a speed of 21 km/h, and the load height is 7.63 m. Additionally, three groups—RC 40, RX 70, and R 70—represent loaders for still gas and gasoline (lift up to 3, 3.5, and 8 tons, respectively).

Still, electric forklifts hold a distinct position in the categorization due to their environmental safety. More than 30 variants are available in the range. The business manufactures machinery with three or four legs that can raise a weight of up to 5000 kg to a height of roughly 8 meters.

Still, stackers are capable of traveling up to 14 km/h. able to lift objects up to a height of 14 meters and with a weight limit of 2.5 tons. Reach trucks come in 14 different variants.

Order pickers have been produced since 2016 and are frequently employed in the food business. There are ten versions in the line. The usual lifting height is within 200 mm, and the maximum load capacity is 2 tons. The Still EK-X pick-up, on the other hand, has a 4.55 m lifting capacity.

Both hydraulic and electric trolleys have a lifting capacity of 3000 and 3300 kg, respectively. The lifting height is 20 cm or less. There are now 17 electric trolley versions and ten hydraulic trolley variants.

Still creates strong electric tractors as well. The trailer load may weigh up to 25 tons and has a carrying capacity of 2 tons. 5000 N is the greatest pulling force.

There are two types of stackers sold under the Still brand: self-propelled and narrow-aisle. Their individual widths and wheelbases vary. The selection comprises two models for small warehouses and 20 self-propelled stackers with lifting heights up to 10 meters and load capacities of up to 2500 kg (up to 1.85 m; up to 1.5 tons).

STILL RX 60-30

Источник

PDFmanual4trucks
Avia
AEC
ACE
AGCO
Agrale
Agrison
Aichi
Albion
Allis Chalmers
Allison Transmission
American LaFrance
AMW
Ariens
Ashok Leyland
Astra
Atlas Copco
Atlas Weyhausen / Weycor
Ausa
Austin
Autocar
Balkancar
Baoli
BAW
Bedford
Beiben
Beifang Benchi
BelAZ
Bell
Bendi
Berliet
BharatBenz
Big Joe
Bis
Bobcat
Bomag
Branson
Brockway
BT
BYD
CAMC
CanyCom
Carer
Case IH
Cesab
Challenger
Chery
Citroen
Claas
Clark
Crown
CVS Ferrari
Daewoo
DAF
Daihatsu
Dalian
David Brown
Dayun
Detroit Diesel Engine
Deutz
Diamond T
Dino
Dodge
DongFeng
Doosan
Dressta
Drexel
Duramax Engine
Dynapac
Eaton Transmission
Ebro
Eicher
ETF
EP
FAW
Fendt
Ferguson
FiatAgri
Ford
Fordson
Foton
Freightliner
GAZ
Gehl
Genie
Ginaf
Gleaner
Godrej
Goodsense
GROS
Hangcha
Hania
Haulotte
Heli
Hino
Hitachi
Holmer
Honda
Howo
Hyster
Hyundai
IFA
International
Iseki
ISUZU
Iveco
JAC
Jacobsen
JCB
Jinma
JLG
John Deere
Jungheinrich
Kalmar
KamAZ
Kato
Kenworth
Kia
Kioti
Kobelco
Komatsu
KrAZ
Kubota
Landini
Landoll
Laverda
LGMG
Liebherr
Linde
Lombardini
Lull
MACK
Magirus-Deutz
Mahindra
MAN
Manitou
Marmon-Herrington
Massey-Harris
MAZ
McCormick
Mercedes-Benz
Mitsubishi
Morooka
MTZ
Mustang
New Holland
Nissan
Noblelift
Oshkosh
Paccar
Pacific
Pegaso
Peterbilt
Pinguely
Renault
REO
Samsung
Sany
Satoh
Scania
Sears
Shaanxi
Shantui
Shibaura
Sinoboom
Sisu
SML
Snorkel
Solis
Sterling
Steyr
Still
Sumitomo
SunBear
Tadano
Takeuchi
TATA
Tatra
Taylor
TCM
Terberg
Terex
Thwaites
Tiger
Toyota
TYM
UD
UniCarriers
Ural
Valtra
Vantage
Versatile
Volvo
Voltas
Wacker Neuson
Wechai Power engines
Western Star
XCMG
Yale
Yanmar
Yuchai
Yuejin
Zetor
ZIL
Zoomlion

Still Forklift operator’s, electrical wiring diagrams, workshop, service and repair manuals, spare parts catalogues, error codes in PDF download

Title	File Size	Download Links
Still 0303, 0305, 0323, 0324, 0325, 0326, 0327, 0328, 0329, 0330, 0331, 0332, 0333, 0334, 0335, 0336, 0337, 0338, 0339, 0340 Original Instructions Manual [PDF]	17.1Mb	Download
STILL 7032-34 / 38-40 / 48-50 Technical Data for Maintenance Service [PDF]	5.9Mb	Download
Still Electric Forklift R20-15 R20-16 R20-18 R20-20 Service Manual [PDF]	22Mb	Download
Still Electric Forklift RX20-15-20, RX60-16-20 Workshop Manual [PDF]	24.5Mb	Download
STILL Electric pallet truck Original instructions [PDF]	2.7Mb	Download
STILL EXD 20 Manual [PDF]	3.1Mb	Download
Still EXP 14, EXP 16, EXP 20, EXP 14D, EXP 16D, EXP 20D, EXP-SF 14D, EXP-SF 16D, EXP-SF 20D, 0301 Original Instructions Manual [PDF]	17.1Mb	Download
Still EXV 14, EXV 16, EXV 20, EXV 14I, EXV 16I, EXV 20I, EXV-SF 14, EXV-SF 16, EXV-SF 20, EXV-SF 14I, EXV-SF 16I, EXV-SF 20I Original Instructions Manual [PDF]	17.1Mb	Download
STILL FM Type 447 Workshop Manual [PDF]	2.1Mb	Download
STILL Forklift Fault Codes [PDF]	2.3Mb	Download

Still Forklift R60-25 Manual [PDF]	11.7Mb	Download
Still GX10 Operating and Maintenance Instructions Manual [PDF]	2.4Mb	Download
Still GX10, OPX 25, OPX 20 PLUS, OPX 25 PLUS, OPX-L 12, OPX-L 16, OPX-L 20, OPX-L 20 S, OPX-D 20, LTX 50 Operating and Maintenance Instructions Manual [PDF]	20.8Mb	Download
STILL iGo neo CX20 Original instructions [PDF]	6.1Mb	Download
STILL M15 / M15T System Diagnosis & Workshop Manual [PDF]	31.8Mb	Download
Still R50-10, 12 / 16 Workshop Service Manual [PDF]	8.1Mb	Download
STILL R60-20-22-25-30-35-40-45-50 Workshop Manual [PDF]	11.7Mb	Download
Still R70-40-45-50 Diesel Forklift Operating Instructions [PDF]	6.4Mb	Download
Still R70-40T, R70-45T, R70-50T Operating Instructions [PDF]	7.1Mb	Download
Still RCD40 Original Instructions [PDF]	20.7Mb	Download
STILL Reach Truck Control Unit RCU Error Code List [PDF]	2.3Mb	Download
Still RX20, RX20-14C, RX20-16C, RX20-16, RX20-16L, RX20-18, RX20-18L, RX20-20L, RX20-16P, RX20-16PL, RX20-18P, RX20-18PL, RX20-20P, RX20-20PL, 6219 Series Original Instructions [PDF]	37.5Mb	Download
Still RX50-10-13-15-16T Parts Catalogue [PDF]	3.7Mb	Download
STILL RX50-10, RX50-13, RX50-15, RX50-16 Manual [PDF]	10.1Mb	Download
STILL RX60-60,RX60-70, RX60-80, RX60-80 / 900 Electric truck Original instructions [PDF]	14.6Mb	Download
STILL RX70 / 40 / 50 LPG Trucks Manual [PDF]	13.2Mb	Download
STILL Service Brochure [PDF]	2.4Mb	Download

The Still forklift is a German-made vehicle. Such equipment is used to move various goods during construction and in warehouses.

Still Electric forklift trucks

RX 20-16 is equipped with a twin-engine front-wheel drive, the voltage of which is 48 V. The design of the equipment provides for battery power and battery replacement.

Electric forklift Still RX 20-16 has the following dimensions:

length — 2.68 m;
width — 1.09 m;
height — 2.16 m.

Still RX 20-16 Technical Specifications:

Weight of the transported cargo — 1600 kg
Weight — 2884 kg
Motor power — 4.5 liters each. With.
Transport speed — 16 km/h
Ground clearance — 123 mm
Wheelbase -1341 mm
Load center of gravity 500 mm
Free weight — 150 mm
Battery capacity — 575 Ah
Working unit lifting height — 3230 mm
Wheel size — 18*7-8
Wheel formula — 2*2
Track Front wheels — 932 mm
Rear wheels — 168 mm
External overall turning radius — 1528 mm
Fork parameters Length — 800 mm
Width — 800 mm
Height — 40 mm
Lifting speed — 430 mm/s

Still RX 20 electric forklift -20 is used to move goods on the territory of warehouses and wagons. The systems are powered by rechargeable batteries.

Still RX 20-16

Still RX 20-20 Technical Specifications:

The largest mass of the lifted load is 2000 kg
The weight of the unit 3453 kg
Engine power is 4.5 liters. With.
Maximum travel speed 16 km/h
Ground clearance — 123 mm
Dimensions — 2918*1138*2160 mm
Center of gravity — 500 mm
Free height — 150 mm
Battery capacity — 700 Ah
Tire size — 200/50-10
Total number of wheels — 4
Number driving wheel mechanisms — 2
Front wheel track — 942 mm
Rear wheel track — 865 mm
Outer overall turning radius — 1883 mm
Operating speed — 380 mm/s

Still R60-25

Still Diesel Forklifts

Still RX 70-30 forklift is equipped with a VW BXT diesel engine. Transport is characterized by a reduced level of fuel consumption and hydraulic mechanical parking brakes.

Still RX 70-30 Technical Specifications:

Load capacity 3000 kg
Gross weight 4235 kg
Number of cylindrical elements 4
Power of the power unit 38 l. With.
Transport speed 21 km/h
Ground clearance — 125 mm
Wheelbase — 1700 mm
Dimensions — 3705*1180*2175 mm
Permissible mast inclination — 10°
Center of gravity — 0.5 m
Free height — 160 mm
Mast length — 3800 mm
Wheel arrangement — 2*2
External turning radius — 2387 mm
Load lifting speed — 470 mm/s
Load lowering speed — 600 mm/s
Hydraulic system pressure — 250 bar

Diesel forklift Stihl RC 40-30 with diesel engine is easy to operate. Vehicle maintenance should be carried out only after 500 hours of operation.

Still RC 40-30 Technical Data:

Maximum weight of transported cargo 3000 kg
Gross weight 4511 kg
Engine power 44 hp. With.
Maximum transport speed 20 km/h
Ground clearance 160 mm
Wheelbase 1620 mm
Dimensions Length — 3710 mm
Width — 1305 mm
Height — 2305 mm
Load center of gravity — 500 mm
Free weight — 160 mm
Lifting height of the working unit — 3250 mm
Wheel size — 27*10-12
Wheel formula — 2*2
Track Front wheels — 1057 mm
Track Rear wheels — 940 mm
External overall turning radius — 2338 mm
Fork parameters Length — 1000 mm
Width — 100 mm
Height — 45 mm
Lifting speed — 510 mm/s

Still Forklift malfunctions and repairs

malfunctions can be caused by a low battery charge, insufficient pressure in the hydraulic transformer system, a dirty safety valve, worn mechanisms, etc.

Repair of Still loaders must be carried out with the power unit turned off and using special tools.

First you need to conduct an external inspection of the failed node. After that, you can begin to disassemble the system and replace worn parts. If the cause of the breakdown was an insufficient
level of fuel or oil fluid, you just need to add it to the required mark.

Источник

Still RC40-16, RC40-18, RC40-20 LPG Forklift Truck Series 4044-4046 Operating & Maintenance Manual

Manual Type: Operators Manual

Still RC40-25, RC40-30, RC40-35 Diesel Forklift Truck Series 4051, 4052, 4053 Operating Instructions

Manual Type: Operators Manual

Still RC40-25, RC40-30, RC40-35 LPG Forklift Truck Series 4054, 4055, 4056 Operating Instructions

Manual Type: Operators Manual

Still RC41-25, RC41-30 Diesel Forklift Truck Series 4091, 4092 Operating & Maintenance Instructions

Manual Type: Operators Manual

Still RC41-25T, RC41-30T LPG Forklift Truck Series 4094, 4095 Operating and Maintenance Instructions

Manual Type: Operators Manual

Still RC41-25, RC41-30 Diesel Forklift Truck Series 4091, 4092 Spare Parts Manual

Manual Type: Parts Manual

Still RC41-25T, RC41-30T LPG Forklift Truck Series 4094, 4095 Spare Parts Manual

Manual Type: Parts Manual

Still R70-16, R70-18, R70-20 Compact Forklift Truck Ser.7052/54/56/58/74-79 Workshop Service Manual

Manual Type: Workshop Service Manual

Still Diesel Forklift Truck R70-16D Series R7031 Spare Parts Catalog, Manual

Manual Type: Parts Manual

Still R70-20T, R70-25T, R70-30T LPG Forklift Truck Series R7038, R7039, R7040 Spare Parts Manual

Manual Type: Parts Manual

Still R70-20, R70-25, R70-30 w.Diesel MB motor Forklift Truck Ser. R7032, R7033, R7034 Parts Manual

Manual Type: Parts Manual

Still R70-16T LPG Forklift Truck Series R7037 Spare Parts Catalogue, Manual

Manual Type: Parts Manual

Still R70-35, R70-40, R70-45 Diesel Forklift Truck Series R7041, R7042, R7043 Spare Parts Manual

Manual Type: Parts Manual

Still R70-35, R70-40, R70-45 Diesel Forklift Truck Series R7048, R7049, R7050 Spare Parts Manual

Manual Type: Parts Manual

Still R70-35, R70-40, R70-45 Diesel Forklift Truck Series R7048, R7049, R7050 Operating Instructions

Manual Type: Operators Manual

Still R70-16, R70-18 Diesel Forklift Truck Series R7052, R7056 Spare Parts Catalog, Manual

Manual Type: Parts Manual

Still R70-20, R70-25, R70-30 Diesel Forklift Truck Series R7062, R7063, R7064 Spare Parts Manual

Manual Type: Parts Manual

Still R70-20i, R70-25i, R70-30i LPG Forklift Truck Series R7065, R7066, R7067 Spare Parts Manual

Manual Type: Parts Manual

Still R70-20T, R70-25T, R70-30T LPG Forklift Truck Series R7068, R7069, R7070 Spare Parts Manual

Manual Type: Parts Manual

Still R70-40, R70-45, R70-50 Diesel Forklift Truck Series R7071, R7072, R7073 Spare Parts Manual

Manual Type: Parts Manual

Still R70-40T, R70-45T, R70-50T LPG Forklift Truck Series R7081, R7082, R7083 Spare Parts Manual

Manual Type: Parts Manual

Still R70-40, R70-45, R70-50 Forklift Truck Series R7071, R7072, R7073 Operating, Maintenance Manual

Manual Type: Operators Manual

Still R70-40, R70-45, R70-50 Forklift Truck Series R7081, R7082, R7083 Operating, Maintenance Manual

Manual Type: Operators Manual

Still R70-16, R70-18, R70-20 Compact Forklift Truck Series R7074, R7075, R7076 Operating Instruction

Manual Type: Operators Manual

Still R70-16, R70-18, R70-20 Compact Forklift Truck Series R7077, R7078, R7079 Operating Instruction

Manual Type: Operators Manual

Still R70-16, R70-18, R70-20 Compact Diesel Forklift Truck Series R7074, R7075, R7076 Parts Manual

Manual Type: Parts Manual

Still R70-16 Military Diesel Forklift Truck Series R7074 BW Spare Parts Manual

Manual Type: Parts Manual

Still R70-16T, R70-18T, R70-20T Compact LPG Forklift Truck Series R7077, R7078, R7079 Parts Manual

Manual Type: Parts Manual

Still R70-35T, R70-40T, R70-45T LPG Forklift Truck Series R7084, R7085, R7086 Operating Instructions

Manual Type: Operators Manual

Still R70-40T, R70-45T, R70-50T LPG Forklift Truck Series R7084, R7085, R7086 Spare Parts Manual

Manual Type: Parts Manual

Still R70-60, R70-70, R70-80 Diesel Forklift Truck Series R7087, R7088, R7089 Spare Parts Manual

Manual Type: Parts Manual

Still R70-60, R70-70, R70-80 Diesel Forklift Truck Series R7090, R7091, R7092 Spare Parts Manual

Manual Type: Parts Manual

Still R70-60, R70-70, R70-80 Forklift Truck Series R7090, R7091, R7092 Operating, Maintenance Manual

Manual Type: Operators Manual

Still R70-16, R70-18, R70-20 Diesel Forklift Truck Series R7094, R7095, R7096 Operating Instructions

Manual Type: Operators Manual

Still R70-16, R70-18, R70-20 Forklift Truck Series R7097, R7098, R7099 Operating, Maintenance Manual

Manual Type: Operators Manual

Still R70-16D, R70-18D, R70-20CD Diesel Forklift Truck Series R7094, R7095, R7096 Spare Parts Manual

Manual Type: Parts Manual

Still R70-16T, R70-18T, R70-20T LPG Forklift Truck Series R7097, R7098, R7099 Spare Parts Manual

Manual Type: Parts Manual

Still (KALMAR) R70-60, R70-70, R70-80 Forklift Truck Series R7126, R7127, R7128 Spare Parts Manual

Manual Type: Parts Manual

Still RX70-16, RX70-18, RX70-20 Diesel Forklift Truck Series 7311, 7312, 7313 Spare Parts Manual

Manual Type: Parts Manual

Still RX70-16, RX70-18, RX70-20 LPG Forklift Truck Series 7314, 7315, 7316 Spare Parts Manual

Manual Type: Parts Manual

Still RX70-22, RX70-25, RX70-30, RX70-35 Forklift Truck Series 7321-7324, 7329, 7330 Parts Manual

Manual Type: Parts Manual

Still RX70-22,RX70-25,RX70-30,RX70-35 Diesel Forklift Truck Ser.7321-7324,7329-7330 Operating Manual

Manual Type: Operators Manual

Still RX70-22, RX70-25, RX70-30, RX70-35 LPG Forklift Truck Series 7325-7328 Operating Instructions

Manual Type: Operators Manual

Still RX70-16, RX70-18, RX70-20 Diesel Forklift Truck ser.R7311, R7312, R7313 Operating Instructions

Manual Type: Operators Manual

Still RX70-16, RX70-18, RX70-20 LPG Forklift Truck Series 7314, 7315, 7316 Operating Instructions

Manual Type: Operators Manual

Still RX70-30H, RX70-35H Hybrid Forklift Truck Series 7323, 7324 Operating, Maintenance Instructions

Manual Type: Operators Manual

Still RX70-40D, RX70-45D, RX70-50D Diesel Forklift Truck Ser.7331, 7332, 7333, 7334 Operating Manual

Manual Type: Operators Manual

Still RX70-40T, RX70-45T, RX70-50T LPG Forklift Truck Series 7335, 7336, 7337, 7338 Operating Manual

Manual Type: Operators Manual

Источник

Download Complete Service Repair Manual for Still R70-40, R70-45, R70-50 Diesel Forklift Truck.

This Factory Service Repair Manual offers all the service and repair information about Still R70-40, R70-45, R70-50 Diesel Forklift Truck. The information on this manual covered everything you need to know when you want to repair or service Still R70-40, R70-45, R70-50 Diesel Forklift Truck.

Click Here To Preview Online

Models Covered:

7071, 7072, 7073, 7081, 7082, 7083
R70-40, R70-45, R70-50

Manual Contents:

Product information
Vorwort
About the R70 4.0t-5.0t
Sicherheitshinweise
Symbols Used
Securing the fork carriage
Working on live electrical components
11. Elektromotor
Fahrmotor
General technical data
Electrical connections
Traction drive
Traction motor
Drehzahlsensor
Pin sensor
Temperatursensor
Temperature sensor KTY84
Generator
General technical data
Alternator
Removing and installing the alternator
12. Verbrennungsmotor
Verbrennungsmotor
Engine unit
Engine unitRemoval and installation
Starter ring gear
Starter motor
Dieselmotor
General technical dataVW 2.0 1 turbodiesel
Diesel engine VW 2.0ITDI
Treibgasmotor
General technical data VW3.2ITG
VWVR6 3.2 1 LPG engine
13. Verbrennungsmotor- Anbauteile
Treibgasanlage
Impco components
Evaporator function- gas mixer
Suction module
0B6 MAP/MAT sensor
Chassis module
Actuator unit
Gas shut-off valve unit
Shut-down due to lack of gas
Maintenance and test specifications
Servicing the LPG filter
Testing CO level in exhaust gases
Evaporator- maintenance
Checking the evaporator for leaks
High-pressure relief valve- 1.7 bar
Treibgasflasche/-tank
LPG cylinder
14. Verbrennungsmotor- Abgasanlage
Abgasanlage-Treibgas
Lambda control system
Lambda sensor
Three-way catalytic converter
22. Mechanische Antriebsachse
Radantrieb
Drive wheel unit
Triebwerk
General technical data Carraro EC 50 l
Drive axle
Removing/installing the drive axle
Differential gearbox and brake
Removal of the differential gearbox and brake
Installation of the differential gearbox and brake
31. Chassis
Gegengewicht
Counterweight
42. Lenksystem
Hydraulische Lenkung
General technical data
Steering system
Steering error detection
Steering unit
Priority valve
Lenkrad und Lenksaule
Steering column
Lenkachse
General technical data
Swing axle
Removing/installing the swing axle
Wheel hub
Steering angle
Tie rod
Axle stub
49. Bremsanlage
Mechanische Betriebsbremse
Service brake
Brake sensor 1B2
Removing/installing the service brake
Changing the brake cable Service brake
Handbremse
Changing the brake cable Parking brake
Parking brake switch
50. Bedienelemente
Einpedal
Accelerator- single-pedal
Zweipedal
Accelerator – double-pedal 1. Generation
Bedienelemente
Multi-levers
Joystick
Joystick operation
Tip switch
Axle assignment
Depressurising the hydraulics
Direction of travel flasher module (Fabli)
56. Anzeigeelemente
Bedienkonsole
Direction of travel flasher display
Display
Display operating unit (ABE 1) Generation 1
ABE 1 Installation and removal
60. Elektrik / Elektronik
Allgemein
General technical data
UbersichtderSteuerungen
Electrical components
Software compatibility
PAN process
Parameter management
Error ring buffer
Insulation measurement
Traction motor temperature monitoring
Drive mode driving behaviour Availability
Driving mode driving behaviour Description
Blue-Q = IQ
Verkabelung
CAN bus connections
Elektrische Anlage
Brake resistor
Fuse box
Fuses
Relays
Sonstige Komponenten
Option board
CAN power port (CPP)
SootCPP (CPP5)
Relay-Power-Port
64. Elektronische Steuerungen
Fahr- und Arbeitshydrauliksteuerung
Truck control unit (TCU)
Truck control unit (TCU) Removal and installation
Umrichter
Inverter
I nvertersRemoval and installation
69. Batterien und Zubehor
Starterbatterie undZubehor
Starter battery
70. Hydraulik
Allgemein
AllgemeineTechnische Daten
Lifting operating speeds
Tilting operating speeds
Lowering operating speeds
Forward tilt safety test
Lowering safety test
Safety checks of hose assembly
Grundhydraulik
Basic hydraulics
Fan motor control unit
Fan control valve
Steering hydraulics
Working hydraulics
Variable displacement pump
Pump regulator
Variable displacement pumpRemoval and installation
Hydraulic tank
Hydraulic oil
Return filter
Breather
Suction filter
High-pressure filter
Conical nipple fittings (CNF)
Boltedjoint
71. Arbeitshydraulik
Neigezylinder
Mast tilt
Tilt cylinders Removal and installation
Changing the set of seals 2200 -5000 kg
Zusatzhydraulik
Attachments
Second operating function for attachments
Clamp locking mechanism for hand levers
76. Ventile
Handhebel
General technical data
Hand lever valve block
Valve block Removal / installation
Directional control valve block
Check valve for hydraulics blocking function
Hydraulic transmitter
Servohydraulik
AllgemeineTechnische Daten
Servo hydraulics valve block
Directional control valve block
Directional control valve function Lifting
Directional control valve function Lowering
81. Hubgeriiste
HubgerQst
General technical data
Telescopic lift mast
Triple mast
Lastketten
Load chains Checking, cleaning
Adjusting the load chains Telescopic mast
Outer load chain Triple mast
Middle load chain Triple mast
Endlagendampfung
End position damping of outer cylinder
Middle cylinder end dampener
Leitungsbruchsicherung
Hose safety valve of triplex mast
Shock valve installation positions
Hubzylinder
Liftjack
Rollen/Stutzrollen
Support roller clearance
84. Lasttrager
Gabeltrager
Fork carriage
Anhang
X Schaltplane
Hydraulik
Hydraulic circuit diagram Multi-levers
Hydraulic circuit diagram Proportional technology

This manual can be used by anyone from a first time owner/amateur to a professional technician.Even the most novice mechanic can also easily follow the step-by-step guides which are made simple by the illustrations and drawings.Keep this manual handy and use it often. Performing routine, preventive maintenance will save you time & money by helping to prevent premature failure and unnecessary repairs.

You will receive a download link immediately after your payment is completed. So please make sure your email address is correct.

File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English

Источник

Quick Links

Related Manuals for Still RX70 Series

Summary of Contents for Still RX70 Series

Page 5: Table Of Contents

Page 13: Foreword

Page 14: Your Truck

Page 17: General

Page 18: Use In The Event Of Frost

Page 19: Ec Declaration Of Conformity In Accordance With Machinery Directive

Page 20: Accessories

Page 22: Labelling Points

Page 25: Nameplate

Page 26: Production Number

Page 27: Proper Use During Towing

Page 28: Place Of Use

Page 29: Using Working Platforms

Page 30: Information About The Documentation

Page 31: Supplementary Documentation

Page 32: Issue Date And Topicality Of The Operating Instructions

Page 33: List Of Abbreviations

Page 35: Definition Of Directions

Page 37: Environmental Considerations

Page 39: Safety

Page 40: Definition Of Responsible Persons

Page 41: Drivers

Page 43: Basic Principles For Safe Operation

Page 45: Changes To The Overhead Guard And Roof Loads

Page 46: Damage, Defects And Misuse Of Safety Systems

Page 48: Medical Equipment

Page 49: Length Of The Fork Arms

Page 50: Residual Risk

Page 51: Special Risks Associated With Using The Truck And Attachments

Page 54: Overview Of Hazards And Countermeasures

Page 57: Danger To Employees

Page 58: Safety Tests

Page 59: Particle Filter

Page 60: Insulation Testing

Page 61: Safety Regulations For Handling Consumables

Page 62: Hydraulic Fluid

Page 63: Battery Acid

Page 64: Diesel Fuel

Page 66: Coolant And Cooling Fluid

Page 68: Emissions

Page 71: Overviews

Page 72: Overview

Page 74: Driver’s Compartment

Page 75: Operating Devices And Display Elements

Page 76: Operating Devices For Hydraulic And Driving Functions

Page 77: Double Mini-Lever

Page 78: Three-Way Mini-Lever

Page 79: Four-Way Mini-Lever

Page 80: Joystick 4Plus

Page 81: Fingertip

Page 82: Mini Console

Page 83: Operation

Page 84: Testing And Activities Before Daily Use

Page 87: Climbing Into And Out Of The Truck

Page 90: Shelves And Cup Holders

Page 94: Adjusting The Armrest

Page 95: Adjusting The Steering Column

Page 96: Unlocking The Emergency Off Switch

Page 97: Seat Belt

Page 100: Using The Driver’s Cab

Page 103: Checking The Steering System For Correct Function

Page 104: Zero Adjustment Of The Load Measurement (Variant)

Page 106: Checking The Vertical Lift Mast Position (Variant) For Correct Function

Page 109: Access Authorisation With Pin Code (Variant)

Page 119: Starting The Engine

Page 121: Operating The Display And Operating Unit

Page 122: Adjusting The Displays

Page 123: Symbols In The Display

Page 128: Setting The Date Or Time

Page 129: Resetting The Daily Kilometres And Daily Operating Hours

Page 130: Softkeys For Operating Various Equipment Variants

Page 132: Blue-Q Efficiency Mode

Page 133: Switching Off Additional Consumers

Page 135: Driving

Page 137: Roadways

Page 139: Setting The Drive Programme

Page 140: Selecting The Drive Direction