Швейная машинка зингер самба 7 инструкция по применению

							When using an electrical appliance, basic safety precautions
should always be followed, including the following:
Read all instructions before using this sewing machine.
1. An appliance should never be left unattended when
plugged in.
2. Always unplug this appliance from the electric outlet
immediately after using and before cleaning.
1. Do not allow to be used as a toy. Close attention is
necessary when this appliance is used by or near children.
2. Use this appliance only for its intended use as described in
this manual. Use only attachments recommended by the
manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the appliance to
the nearest authorized dealer or service center for
examination, repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air openings blocked.
Keep ventilation openings of the sewing machine and foot
controller free from accumulation of lint, dust, and loose
cloth.5. Keep fingers away from all moving parts. Special care is
required around the sewing machine needle.
6. Always use the proper needle plate. The wrong plate can
cause the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the
needle causing it to break.
9. Switch the sewing machine off (O) when making any
adjustments in the needle area, such as threading needle,
changing needle, threading bobbin, or changing presser foot,
and the like.
10.Always unplug sewing machine from the electrical outlet
when removing covers, lubricating, or when making any other
user servicing adjustments mentioned in the instruction
manual.
11.Never drop or insert any object into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol (spray products are being
used or where oxygen is being administered).
14.To disconnect, turn all controls to the off (O) position, then
remove plug from outlet.
15.Do not unplug by pulling on cord. To unplug, grasp the plug,
not the cord.
This sewing machine is intended for household use only.
DANGER
WARNING
SAVE THESE INSTRUCTIONS- To reduce the risk of electric shock:
- To reduce the risk of burns, fire, electric
shock, or injury to persons: 3. Always unplug before re-lamping. Replace bulb with same
type rated 10 watts (110-120V area) or 15 watts (220-240V
area).
IMPORTANT SAFETY INSTRUCTIONS 
						

							Congratulations
As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in
creativity. From the moment you first use your machine, you will know you are sewing on one of
the easiest to use sewing machines ever made.
May we recommend that, before you start to use your sewing machine, you discover the many
advantages and the ease of operation by going through this instruction book, step by step,
seated at your machine.
To ensure that you are always provided with the most modern sewing capabilities, the
manufacturer reserves the right to change the appearance, design or accessories of this
sewing machine when considered necessary.
This Instruction Book covers the operation of multiple models of sewing machines and the use
of optional accessories. The manufacturer has made every effort to clearly define the
differences between the different models and to define when an accessory is an optional extra.
Please read carefully to determine which instructions apply to your particular model machine.
For a clear definition of your sewing machine please see pages 19.	
	
	
	
		
	


	

	
	
	
	 	

Please note: 
						

							Principal parts of the machine.....................................................2/3
Accessories....................................................................................4
Fitting the snap-in sewing table .....................................................5
Connecting machine to power source............................................6
Changing the bulb ..........................................................................7
...................................................9
11
Raising the bobbin thread ............................................................16
Reverse sewing/ Removing the work/ Cutting the thread ............17
Matching needle/ fabric/ thread....................................................18How to choose your pattern .........................................................19
Blind hem/ lingerie stitch ..............................................................21
Overlock stitches (for models A, B & C) .......................................22
Sewing on buttons .......................................................................23
Sew 4-step buttonholes ...............................................................24
Zippers and piping .......................................................................25
Sewing with the optional hemmer foot .........................................26
Multi-stitch zig-zag .......................................................................27
Honeycomb stitch ......................................29
Sewing with the optional cording foot ..........................................30
Free motion darning .....................................................................31
Practical stitches .......................................32
Maintenance ................................................................................33
Trouble shooting guide ................................................................34 Two-step presser foot lifter/ Adjusting presser foot pressure .........8
Attaching the presser foot holder
Winding the bobbin ......................................................................10
Inserting the bobbin......................................................................
Inserting and changing needles ...................................................12
Threading the upper thread .........................................................13
Automatic needle threader (optional) ...........................................14
Thread tension .............................................................................15Function of stitch width dial and stitch length dial ........................20
Straight stretch stitch and Ric Racstitch (for models A, B &C) ....28
(for models A, B & C)
(for models A, B & C)
List of contents 
						

							1. Thread tension dial
3. Thread take-up lever
5. Presser foot
6. Needle plate
7. Removable sewing table/accessory storage
8. Bobbin stopper
9. Stitch length dial
11. Pattern indicator window
12. Reverse sewing lever2. Presser foot pressure adjustment
4. Thread cutter
(not on all models)
10. Stitch width dial (not on all models)
2
Principal parts of the machine
1
2
3
4
5
6
78
9
10
11
12 
						

							13. Horizontal spool pin
22. Handle
23. Presser foot lever
24. Feed speed control
25. Power cord 14. Bobbin winder
15. Handwheel
16. Pattern selector dial
17. Power and light switch
18. Main plug socket
19. Bobbin thread guide
20. Upper thread guide
21. Face plate
3
Principal parts of the machine
24
25 13
14
15
16
17
1819
20
22
23
21 
						

							Standard a Optional accessoriesccessories
a. All purpose foot
Buttonhole foot
Button sewing foot
L-screwdriver
Seam ripper/ brush
g. Oil bottle
Pack of needles
Bobbin (3x)
L. Spool holder(These 6 accessories are not
supplied with this machine;
they are however available as
special accessories from your
local dealer.)
m. Satin stitch foot
n. Overcasting foot
o. Hemmer foot
p. Blind hem foot
q. Cording foot
r. Darning foot b. Zipper foot
c.
d.
e.
f.
h.
I.
j. Seam guide
k. Darning plate
Optional a iccessor es available at extra cost
4
Accessories
Standard a riccesso es
a
bc
d
g
ij
mo e
p
q
h
k f
r nl
006806008 006905008006909008
006914008
006804008
006803008006800008
006810008 006016008 006812008 
						

							Keep the snap-in sewing table horizontal, and push it in the
direction of the arrow. (1)
The inside of the snap-in sewing table can be utilized as an
accessory box.
To open, lift up at the point of the arrow. (2)
5
Fitting the snap-in sewing table 
						

							Polarized attachment plug
Conductor
intended to be grounded Connect the machine to a power source as illustrated. (1)
For appliance is equipped with a polarized plug which must be
used with the appropriate polarized outlet. (2)
Unplug power cord when machine is not in use.
The foot control pedal regulates the sewing speed. (3)
Consult a qualified electrician if in doubt as to connect
machine to power source.
Unplug power cord when machine is not in use.
The foot control must be used with the appliance by 4C-
316B (110-120V area) / 4C-326G (230V area) / 4C-316C or
4C-326C (220-240V area) manufactured by Panasonic Co.,
Ltd.(TW)
Press main switch (A) for power and light on  l .
For appliance with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If it does
not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper outlet. Do
not modify the plug in any way. Attention:
Attention: Foot control
Sewing light
IMPORTANT NOTICE
1
2
3
6
Connecting machine to power source
A 
						

							Disconnect the machine from the power supply by removing
the plug from the main socket!
- Loosen screw (A) as illustrated. (1)
- Remove the face plate (B).
- Unscrew the bulb and install a new one (C). (2)
- Replace the face plate and tighten screw.
Should there be any problem, ask your local dealer for advice.
7
Changing the bulb
1
2C
AB