Semi automatic round bottle labeling machine mt 50 инструкция

KL-S180 Полуавтоматическая этикетировочная машина для круглых бутылок

This machine is manufactured by Zhejiang Kangling Machinery
Manufacturing CO., LTD and is designed for semi-automatic labeling
of round bottle products in daily chemical, food and beverage,
medicine, chemical, and other light industries.

Обзор

• Can label round bottles of various sizes
• Suitable for small batch and multi-variety production
• Can only be used for stand-alone labeling
• Strict compliance with the instruction manual is required for
  использование

Технические характеристики

• Semi-automatic labeling for efficient production
• Accurate labeling with adjustable label position
• High precision with no bubbles or wrinkles on the label
• Durable machine with long service life

Технические параметры

The technical parameters for the KL-S180 semi-automatic round
bottle labeling machine are as follows:

• Labeling speed: 20-40 pieces/minute
• Bottle diameter: Φ15-120mm
• Высота бутылки: 25-300 мм
• Label size: maximum width 130mm, maximum length 250mm
• Accuracy: ±0.5mm (excluding product and label errors)
• Voltage: AC220V 50/60HZ
• Мощность: 120W
• Machine size: 650mm × 450mm × 450mm
• Вес машины: 25kg

Инструкции по использованию

1. Place the KL-S180 semi-automatic round bottle labeling machine
   на ровной и устойчивой поверхности.
2. Connect the machine to an AC220V power supply with a stable
   обtagе и частота.
3. Adjust the labeling position according to the bottle size and
   label size using the adjustable label position feature.
4. Place the round bottles to be labeled on the conveyor belt,
   ensuring they are properly aligned.
5. Turn on the machine and it will start labeling
   автоматически.
6. Monitor the labeling process and make adjustments as necessary
   for accurate and efficient labeling.
7. When finished, turn off the machine and clean any leftover
   adhesive or debris from the machine.

Note: This machine can only be used for stand-alone labeling.
For other uses, please consult the manufacturer. The manufacturer
is not responsible for any damage caused by non-compliant use. Such
risks are solely borne by the user.

KL-S180 semi-automatic round bottle
маркировочная машина
руководство по эксплуатации
Zhejiang Kangling Machinery Manufacturting CO.,LTD

А. Болееview
1. Scope of application KL-S180 semi-automatic round bottle labeling machine is an ideal
equipment for semi-automatic labeling of round bottle products in daily chemical, food and beverage, medicine, chemical and other light industries.
This machine is suitable for round bottles of various sizes and is suitable for small batch and multi-variety production. This machine can only be used for stand-alone labeling.
For other uses, please consult the manufacturer. The manufacturer is not responsible for any damage caused by non-compliant use. Such risks are solely borne by the user.
Strict compliance with the instruction manual is part of the requirements for the use of this machine. 2. Performance characteristics
This machine has reasonable structure, reliable performance and simple operation. Using photoelectric detection, accurate labeling. ·Adopt advanced labeling mechanism to ensure labeling accuracy. ·Can label a variety of bottles with strong adaptability. ·The label photoeye can identify and compare label backing papers with different light transmittances, and move the photoeye position to make the best adjustments to labels of different lengths to ensure normal labeling and smooth and accurate labeling. ·All mechanisms including frame, shell, traction device, crossbar and fasteners are mostly made of stainless steel and aluminum materials. They are used in a normal working environment to ensure no rust and pollution. ·The system control components all have international standardization certification, and have undergone strict inspection and testing in the factory to ensure the reliability of various functions.
Б. Технические параметры
1. Machine parameters The maximum output of a single non-positioning labeling: 50 pieces/min (related to the size of the bottle label) Labeling bottle outer diameter: 20-150mM Power: 50W Voltage: 110V 60Hz Operating environment temperature: 5-45 Weight: 25Kg Relative humidity: 15-90% Dimensions: 800X320X460mm 2. Overriding parameters Labeling speed: 3-15m/min Labeling accuracy: ±0.5mm (excluding package and label errors)

Minimum length of labeling: 10mm 3. Label parameters ·Label bottom paper adopts Glassine bottom paper (that is, translucent bottom paper or translucent bottom paper) ·The thickness of the label paper is not less than 5µm ·The outer diameter of the label roll is <300mm, and the inner diameter of the label roll core is 76mm
C. construction and installation
1. Schematic diagram of winding mark
2. Схема
1. Bottle pressure swing arm 2. Bottle pressure roller 3. Over-label roller 4. Positioning rod 5. Bottle supporting roller

6. Bottle supporting bracket 7. Position adjustment handle 8. Stripping plate 9. Guide roller 10. Traction roller locking handle 11. Traction roller 12. Foot base 13. Motor 14. Bottom paper recovery roller 15. Main mounting plate 16. Feed tray device 17. Travel switch 18. Swing arm tension spring 19. Marking sensor
D. adjustments before starting
1. Adjust the bottle support Loosen the position adjustment handle screws under the left and right brackets of the
bottle holding roller (Figure 1-7), adjust and move the bottle holding bracket (Figure 1-6) according to the diameter of the labelled round bottle, so that the bottle is on the bottle holding roller (Figure 1 -5) Between the labeling roller (Figure 1-3); the larger the diameter of the bottle, the greater the distance between the two rollers. After adjusting to a suitable position, tighten the handle screw. 2. Adjust the pressure bottle roller
Loosen the handle screws at both ends of the bottle pressing roller (Figure 1-2), and adjust the bottle pressing roller to the proper position so that the bottle pressing roller just presses the bottle when it rotates with the bottle pressing swing arm (Figure 1-1). In the center position, tighten the handle screw after adjustment. 3. Adjust the limit switch to touch the screw
First loosen the touch screw downwards, and then turn the bottle pressing swing arm (Figure 1-1) to make the bottle pressing roller (Figure 1-2) press the labeling round bottle, and slowly move the touch screw to the stroke switch ( Figure 1-17) Adjust the direction until the flap against the travel switch makes a switch action sound. After the adjustment is completed, tighten the nut. 4. Adjust the position of the positioning rod
Adjust the positioning rod to the proper position so that the label is affixed to the correct position of the bottle. 5. Adjust the label stripping board
Adjust the stripping plate (Figure 1-8), make the stripping plate as close as possible to the overlaid roller (Figure 1-3), but not in contact with it. 6. Install label roll
As shown in Figure 1, install the entire roll of labels on the feeding tray device (Figure 1-16), with the label side facing up and the bottom paper side down, install the

label paper according to the drawing diagram, and finally lock both sides of the traction roller The handle screw makes the knurled aluminum wheel press the rubber traction roller to have a certain pressure, and the pressure on both sides is even. 7. Adjust the position of the electric eye
Adjust the left and right positions of the plate metal of the electric eye to adjust the length of the pre-out mark. The length of the label beyond the stripping plate is generally 3-5mm. 8. Clean up before booting
Remove all the sundries on the traction roller, guide roller, stripping plate, label covering roller, bottle holding roller, bottle pressing roller, and chassis, and check whether all screws are tight.
E. Electrical equipment adjustment
1. Power and switch This model uses AC 220V voltage and a single-phase three-wire three-core power
plug. Check the power socket used before use to ensure that the machine is reliably grounded. Plug in the power cord and turn on the power switch. 2. Setting up the standard measuring electric eye
Key operation: Press and hold the button for 4 seconds, the red indicator light flashes once,
release the button at this time, and the product is in the calculation state. At this time, move the tested label back and forth, and the product automatically records related parameters. After the recording is completed, the red light stops flashing and becomes a steady light.
Press and hold the button for 4 seconds, the red indicator light flashes once, after keeping the button pressed for 8 seconds, the indicator light flashes again. The output state of the product is switched between normally open and normally closed. Note: This product has been adjusted to normally open output from the factory, and general customers do not need to select this function.
·The red indicator light is the status light; ·The green indicator light is the output signal indicator;
Voltagе: постоянный ток: 24 В
F. Start-up operation workflow
When all the relevant parameters are set and debugged, turn on the power, put the round bottle between the bottle support roller and the labeling roller, the bottom of the bottle is against the positioning rod, and the bottle pressing arm is used to make the bottle pressing roller press the label. Round bottle, at this time, the lower end of the swing arm touches the screw and just touches the travel switch, the travel switch is turned on, and the signal is transmitted to the control module. The control module drives the motor to run. The motor drives the traction roller, the labeling roller, and the bottom paper through the sprocket chain. Recycle the roller, pull the label paper, and peel off the label from the label bottom paper by peeling the label board, and at the same time, the labeling roller drives

the round bottle to rotate together. At this time, the peeled off label is attached to the round bottle. In position, the labeling is completed. The normal labeling work is repeated in this way.
Ж. Техническое обслуживание
The operators of this machine must be trained before they can operate and use the machine. In order to maximize the efficiency of the machine, the user must always pay attention to the operation of the machine during use and should do routine and regular maintenance of the machine. The following is a guide for maintenance. 1. Daily maintenance
Everyday before starting ·It is necessary to check whether there are sundries on the rubber rollers, traction rollers, guide rollers, stripping plates, etc.; ·Observe whether the power supply is normal and whether the power cord is damaged; · Regularly clean and maintain the machine surface; ·Pay attention to observe whether there are loose screws on the machine, if found, tighten them immediately;
H.Malfunction and solutions

Симптом

Вызывать

Решения

1. No Label

Wrong position of travel switch Travel switch error

Adjust the position of the travel switch Replace the travel switch

The traction roller does not press the label tape tightly, and it slips when pulling the label The power switch is not turned on

Tighten the adjusted handle screw
Откройте выключатель питания

2. Continuous label
3. Inaccurate labeling axial position

The position of the measuring standard electric eye is wrong or the label tape does not pass through the detection position of the electric eye slot Marking electric eye error
The front and rear position of the positioning rod is not positioned The position of the label on the stripping board is incorrect The bottom of the bottle did not stick to the positioning rod when placing the bottle

Adjust the position of the electric eye
Adjust or replace the electric eye Lock the positioning rod
Re-adjust the label position
Please put the bottle correctly

4. Not labelled
5. Wrinkles after label application
6. Large displacement of the label at the beginning and the end after the roll is
прикладной

The reserved label is not long enough
The surface of the object is not sufficiently sticky with the label or the humidity is too high The bottle pressing roller does not press the round bottle to be pasted, and the round bottle to be pasted does not rotate Reserved label is too long
There is debris on the surface of the round bottle Label peeling plate and labeling rubber roller The label paper is not straightened, and the peeled label is not straight
The peeling plate is not parallel to the axis of the bottle to be labeled
The label tape swings back and forth when the label tape is hung obliquely or pulled.
The labeling area of the labeling area has too much error in diameter The distance between the peeling label and the bottle body is too far or there is a slight collision between the two The mounting plate of the peeling label is not fastened, and it shakes during the labeling process The bottle is not clean or has water

Adjust the length of the reserved label Check the surface of the bottle
Adjust the bottle gap
Reduce the length of the reserved label Clean the surface of the bottle Adjust the distance appropriately Adjust the feeding tray device to tighten the label Adjust the adjustable roller, the position of the stripping plate, so that the bottle holding roller, the stripping plate and the overlaid roller are parallel Fasten the stop ring on the guide roller to prevent the label from swinging back and forth The reason for being posted on the round bottle Normal state is about 3-5mm
Снова затяните винты.
Change a clean and dry bottle

Документы / Ресурсы