Руководство к швейным машинам компании зингер 127к

Quick Links

*

127-3 & 128-3

with VIBRATING SHUTTLE

Copyright, U. S. A., 1915, 1923, 1929, 1932, 1935

and 1940, by The Singer Manufacturing Company

All Rights Reserved for all Countries

*A Trade Mark of

THE SINGER MANUFACTURING CO.

INSTRUCTION MANUAL

Table of Contents

| Next Page

• Page 1: Instruction Manual

  127-3 & 128-3 with VIBRATING SHUTTLE Copyright, U. S. A., 1915, 1923, 1929, 1932, 1935 and 1940, by The Singer Manufacturing Company All Rights Reserved for all Countries *A Trade Mark of THE SINGER MANUFACTURING CO. INSTRUCTION MANUAL Table of Contents…

• Page 2
  Main Parts Instructions for Operating the Machines To Remove the Shuttle To Wind the Bobbin To Thread the Shuttle To Replace the Shuttle To set the Needle To Thread the Needle To Prepare for Sewing To Commence Sewing To Remove the Work Tensions To Regulate the Tensions To Turn a Corner…
• Page 3
  TO ALL WHOM IT MAY CONCERN: The improper placing or renewal of the TradeMark «SINGER» or any other of the Trade Marks of The Singer Manufacturing Company (all of which are duly Registered Trade Marks) on any machine that has been repaired, rebuilt, reconditioned, or altered in any way whatsoever outside a SINGER factory or an authorized SINGER agency is forbidden.
• Page 4
  Instructions for Operating the Machines Raise the presser foot (B, Fig. 3) by means of the presser bar lifter (C, Fig 3) to prevent injury to the foot (B, Fig. 3) and feed (A, Fig. FIG 3. FRONT VIEW OF THE MACHINE It is necessary to understand the stop motion (E, Fig.
• Page 5
  To Ensure Perfect Action of the Machine The balance wheel must always turn over toward the operator. Do not run the machine with the presser foot resting on the feed without cloth under the presser foot. Do not run the machine when both shuttle and needle are threaded unless there is material under the presser foot.
• Page 6
  To Wind the Bobbin Release the balance wheel (D, Fig. 3) by turning the stop motion screw (E, Fig. 3) over toward you. Draw to the left the knob (A, Fig. 6, page 7) and place the bobbin between the cups (B and C, Fig.
• Page 7
  To Thread the Shuttle Hold the shuttle between the thumb and fin- gers of the left hand as shown in Fig. 7. Place the bobbin into the shuttle with the thread drawing toward the right from the side of the bobbin nearest you, as shown in Fig. 7. Place the forefinger of the left hand on the end of the bobbin and draw the thread down- ward into the long slot in the shuttle as far as…
• Page 8
  127-3 & 128-3 To Replace the Shuttle After threading, take the shuttle in the right hand with the point toward you and the ten- sion adjusting screw (1, Fig. 7, page upwards. Put the point of the shuttle into the front end of the shuttle carrier as shown in Fig.
• Page 9
  To Thread the Needle SEE FIG. 11 Turn the balance wheel over toward you until the thread take-up lever (4) is raised to its highest point. Place the spool of thread on the spool pin at the top of the machine, lead the thread into the thread guide (1) at the top of the face plate, down under and from right to left between the tension discs (2), into the…
• Page 10
  To Prepare for Sewing With the left hand hold the end of the needle thread, leaving it slack from the hand to the needle. Turn the balance wheel over toward you until the needle moves down and up again to its highest point thus catching the bobbin thread, draw up the needle thread and the bobbin thread will come up with it through the hole in the throat plate (see Fig.
• Page 11
  Tensions For ordinary stitching the needle and the bob- bin threads should be locked in the centre of the thickness of the material, thus: FIG. 13. PERFECT STITCH If the tension on the needle thread is too tight, or if that on the bobbin thread is too loose, the needle thread will lie straight along the upper surface of the material, thus: FIG.
• Page 12
  To Turn a Corner Stop the machine with the needle at its low- est point. Raise the presser foot and turn the work as desired, using the needle as a pivot. To Regulate the Length of Stitch The length of stitch is regulated by the large thumb screw (E, Fig.
• Page 13
  The Belt See that the belt is not too tight; it should always be tight enough not to slip. If too loose remove the hook at one end, shorten the belt and rejoin. Machine Working Heavily. If the machine runs hard after standing idle for some time use a little kerosene in the oil- ing places, run the machine rapidly, then wipe clean and oil.
• Page 14
  To Oil the Machine To ensure easy running, the machine requires oiling and if used continuously it should be oiled each day. With moderate use all occa- sional oiling is sufficient. Oil should he applied at each of the places shown by arrows in Figs.
• Page 15
  To Oil the Machine continued… On the back of the arm is a round plate or cover, fastened by a thumb screw. Loosen the screw, turn the plate upward and fasten by tightening the screw; turn the balance wheel slowly and oil the moving parts inside, then turn the cover down and fasten it as before.
• Page 16
  INSTRUCTIONS FOR USING THE ATTACHMENTS FOOT HEMMER — Hemming Raise the needle to its highest point. Remove the presser foot and attach the foot hemmer in its place (see Fig. 18). Clip off the right hand corner of the cloth, so that it will take the roll easily, turn up the edge about a quar- ter of an inch, insert it in the mouth of the hemmer and draw or push it along until under…
• Page 17
  FOOT HEMMER — Felling The two pieces of cloth to be felled should be laid one over the other, right sides together, the edge of the under piece being a little far- ther to the right than the upper piece. Stitch them together, using the hemmer as a press- er foot, the front end of the hemmer forming a guide for the edges of both pieces, the upper…
• Page 18
  ADJUSTABLE HEMMER — Hemming Remove the presser foot and attach the adjustable hemmer in its place as shown in Fig. 22. This hemmer will turn hems from 3/16 inch to 15/16 in. wide The adjustment is made by loosening the thumb screw on the hemmer and moving the scale to the right or left until the hem turned is of the desired width.
• Page 19
  BINDER — Binding Remove the presser foot and attach the binder in its place. Pass the binding through the scroll of the binder and draw it back under the needle. Place the edge of the goods to be bound between the scrolls of the binder and draw it under the needle.
• Page 20
  TUCKER Remove the presser foot and attach the tuck- er in its place. The width of the tuck is deter- mined by the scale of figures nearest the needle, which shows in eighths and six- teenths of an inch the distance of the edge of the fold from the line of stitching.
• Page 21
  FIG. 26. THE RUFFLER AND ITS PARTS Ruffler Lines 1, 2, 3, 4 and .5 shown in Fig. 26 indi- cate where the material is to be placed for various operations, as follows: Line 1 — the correct position for the material to which the ruffled material is applied.
• Page 22
  Ruffler — Principal Parts continued… H — RUFFLING BLADE—the upper blue steel blade with the teeth at the end to push the material in plaits up to the needle. J — SEPARATOR BLADE—the lower blue steel blade without teeth, which pre- vents the teeth of the ruffling blade coming into contact with the feed of the machine, or the material to which ruf-…
• Page 23
  To Make a Ruffle and Sew it to a Garment in One Operation Insert the material to be ruffled between the two blue blades, as shown in Fig. 28, follow- ing the line 2, in Fig. 26. Place the garment to which the ruffle is to be attached, under the separator blade, following the line 1, in Fig.
• Page 24
  Piping a Ruffle Insert the material to be ruffled between the two blue blades, following the line 2, in Fig. 26. This material must not be over 1 1/4 inch- es wide, as it is carried through the ruffler with the finished edge of the ruffle to the right of the attachment as shown In Fig.
• Page 25
  If the ruf- fler does not plait evenly, a drop of oil may remedy the trouble. SINGER Needles should be used in SINGER Machines. These Needles and their Containers are marked with the Company’s Trade Mark «SIMANCO»*…
• Page 26
  RELATIVE SIZES OF NEEDLES AND THREAD (Class and Variety of Needles Used, 15×1) CLASSES OF WORK SIZES OF Georgette, chiffon, net, light weight synthetic, NEEDLES fabrics, fine dimity, lawn, batiste, and other feath- erweight or sheer fabrics. For infants’ clothes and for dainty lingerie;…

ИнфоСделать ставкуПоложить в корзину

Вы можете наблюдать за ходом торгов по этому лоту, добавив его в «Избранное».

5 человек добавили лот в Избранное

Увлеченным

• Антиквариат и Искусство
• Видео, Фильмы
• Винтаж
• Книги, журналы, газеты
• Коллекционное
• Музыка
• Сделано своими руками

Все в дом

• Видео, Фильмы
• Домашний очаг, Сад, Дача
• Книги, журналы, газеты
• Музыка
• Строительство и Ремонт
• Флора и Фауна

Наша цель — обеспечить Вам самый быстрый доступ к руководству по эксплуатации устройства Singer 127-3 & 128-3. Пользуясь просмотром онлайн Вы можете быстро просмотреть содержание и перейти на страницу, на которой найдете решение своей проблемы с Singer 127-3 & 128-3.

Для Вашего удобства

Если просмотр руководства Singer 127-3 & 128-3 непосредственно на этой странице для Вас неудобен, Вы можете воспользоваться двумя возможными решениями:

• Полноэкранный просмотр -, Чтобы удобно просматривать инструкцию (без скачивания на компьютер) Вы можете использовать режим полноэкранного просмотра. Чтобы запустить просмотр инструкции Singer 127-3 & 128-3 на полном экране, используйте кнопку Полный экран.
• Скачивание на компьютер — Вы можете также скачать инструкцию Singer 127-3 & 128-3 на свой компьютер и сохранить ее в своем архиве. Если ты все же не хотите занимать место на своем устройстве, Вы всегда можете скачать ее из ManualsBase.

Печатная версия

Многие предпочитают читать документы не на экране, а в печатной версии. Опция распечатки инструкции также предусмотрена и Вы можете воспользоваться ею нажав на ссылку, находящуюся выше — Печатать инструкцию. Вам не обязательно печатать всю инструкцию Singer 127-3 & 128-3 а только некоторые страницы. Берегите бумагу.

Резюме

Ниже Вы найдете заявки которые находятся на очередных страницах инструкции для Singer 127-3 & 128-3. Если Вы хотите быстро просмотреть содержимое страниц, которые находятся на очередных страницах инструкции, Вы воспользоваться ими.