Робот пылесос самсунг джет бот инструкция

Jet Bot User manual VR30T80**** series

Before operating this unit, please read the instructions carefully.

For indoor use only

1_VR8000_EN_00857B-00_AA.indd 1 2021-12-10 3:54:15

Contents

PREPARATION

Safety information 3

INSTALLATION

Installing a Docking Station 15

OPERATION

Charging the Jet Bot 16

OPERATION

Using the Jet Bot 19

Basic use 19

Operation status on the LED Status Indicator 20

Cleaning Functions 21

Additional functions 22

Attaching Boundary Markers 23

Parts diagram 24

Jet Bot 24

Docking Station 24

MAINTENANCE

Cleaning the Jet Bot 25

Emptying and cleaning the Dustbin 25

Cleaning the brush 26

Cleaning the Sensor Window 27

Cleaning the Driving Wheel 27

Cleaning the Spin Brush 28

APPENDIX

SmartThings App 29

Setting up the wireless router 29

Downloading the SmartThings App 30

Setting up a SAMSUNG account 30

Registering a device to the SmartThings App 30

Software Update 31

Functions of the SmartThings App 32

Notes and cautions 34

Installation 34

Charging 34

Using 35

Cleaning and maintenance 36

Battery usage 37

Corrective measures before reporting a problem 38

Troubleshooting 39

Open Source Announcement 44

How to reset to the factory default 44

Product Specification 45

English2

1_VR8000_EN_00857B-00_AA.indd 2 2021-12-10 3:54:15

P R

E PA

R A

TIO N

PREPARATION

Safety information

Before operating the appliance, please read this manual thoroughly and retain it for your reference.

Because the following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual.

Caution/Warning symbols used

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

Other symbols used

NOTE

Indicates that the following text contains additional important information.

Accessories Accessories may differ depending on the models.

Docking Station Pre-motor Filter: 2 units (Inside the product: 1 unit,

Spare: 1 unit)

Spin Brush: 2 units (Inside the product: 1 unit,

Spare: 1 unit)

Battery Charger/Power cord Boundary Markers User Manual

English 3

1_VR8000_EN_00857B-00_AA.indd 3 2021-12-10 3:54:17

P R

E PA

R A

TIO N

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

L i — i o n

For battery recycling go to call2recycle.org

or call 1-800-822-8837

Failure to meet these requirements could cause damage to the internal parts of the vacuum and void your warranty.

General

Do not allow to be used as a toy. Close attention is necessary when used by or near children.

Use only as described in this manual.

Do not operate the Jet Bot or the Docking Station if it has been damaged in any way.

If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a customer care center.

Do not handle the Docking Station or the Jet Bot if your hands are wet.

Use only on dry, indoor surfaces.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should not clean or perform maintenance on the vacuum without adult supervision.

Move the cords of other appliances so they are not in the area that is to be cleaned.

Do not operate the vacuum in a room where an infant or child is sleeping.

English4

1_VR8000_EN_00857B-00_AA.indd 4 2021-12-10 3:54:18

P R

E PA

R A

TIO N

Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor.

Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.

Do not allow children to sit on the vacuum.

Do not use the vacuum on a wet surface.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Docking Station

Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

Do not use outdoors or on wet surfaces.

Unplug the Docking Station from the outlet when not in use and before servicing.

Use only the Docking Station supplied by the manufacturer to recharge.

Do not use with a damaged cord or a plug or a loose power outlet.

Do not pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.

Do not use extension cords or outlets with inadequate current carrying capacity.

Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

Do not mutilate or incinerate batteries as they will explode at high temperatures.

Do not attempt to open the Docking Station. Repairs should only be carried out by a qualified customer care center.

Do not expose the Docking Station to high temperatures or allow moisture or humidity of any kind to come into contact with the Docking Station.

Do not charge the non-rechargeable batteries with the Docking Station.

English 5

1_VR8000_EN_00857B-00_AA.indd 5 2021-12-10 3:54:18

P R

E PA

R A

TIO N

Jet Bot

Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on.

Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

Also do not use in:

Locations with candles or desk lamps on the floor.

Locations with unattended fires (fire or embers).

Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

Do not use the Jet Bot in an enclosed space filled with vapors given off by oil based paint, paint thinner, moth proofing substances, flammable dust, or other explosive or toxic vapors.

Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid gets on the skin, wash quickly with water. If the liquid gets into the eyes, flush them immediately with clean water for a minimum of 10 minutes. Seek medical attention.

English6

1_VR8000_EN_00857B-00_AA.indd 6 2021-12-10 3:54:18

P R

E PA

R A

TIO N

Power related

WARNING

Please prevent any risk of electric shock or fire.

Do not damage the power cord.

Do not pull the power cord too hard or touch the power plug with wet hands.

Do not use a power source other than 100-240 V~ 50-60 Hz and also do not use a multi-outlet to supply power to a number of devices at the same time. (Do not leave the cord carelessly on the floor.)

Do not use a damaged power plug, a power cord or a loose power outlet.

Clean dust or any foreign matter on the pin and the contact part of the power plug.

There is a risk of electric shock or malfunction.

Before use

WARNING

Do not use the Jet Bot near a heater or combustible materials.

Do not use the Jet Bot near fire or flame such as a movable heater, a candlelight, a desk lamp, a fireplace, etc. or in a place where combustible materials such as gasoline, alcohol, thinner, etc. exist.

Make sure there are no dangerous objects around the Jet Bots cleaning area to prevent collision and unplug any electric heaters or fans.

The Jet Bot can be damaged or malfunction.

The Jet Bot is intended for household use therefore do not use it in an attic, basement, storage, an industrial building, out of indoor space, places with moisture (such as a bathroom, a laundry room), on the table or shelves.

The Jet Bot can be damaged or malfunction.

English 7

1_VR8000_EN_00857B-00_AA.indd 7 2021-12-10 3:54:18

P R

E PA

R A

TIO N

Attach the Boundary Markers to a place where the Jet Bot may fall such as a stair or a banister to prevent product damage and injury.

Please keep the Cliff Sensor clean all the time for safety.

Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.).

The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid.

Do not spill any liquids on the Docking Station.

There is a risk of fire or electric shock.

Do not use the Docking Station for anything other than its intended purposes.

There is a risk of fire or severe damage to the Docking Station.

Always keep the Cliff Sensor clean for your safety.

As this wireless installation may cause radio interference, it cannot provide a service related with human safety.

CAUTION

Insert the Dustbin before using the Jet Bot.

When installing the Docking Station, do not leave the cord carelessly on the floor since the Jet Bot may get tangled by it.

To clean all areas of your house, open all rooms and set the No-go Zones with the SmartThing App or attach the Boundary Markers to the places where the Jet Bot may get damaged such as a front door, a veranda, a bathroom, and stairs for safety.

Follow these recommendations for proper automatic recharging.

Always turn on the power of the Docking Station.

Install the Docking Station where the Jet Bot can easily find.

Do not leave any objects in front of the Docking Station.

English8

1_VR8000_EN_00857B-00_AA.indd 8 2021-12-10 3:54:19

P R

E PA

R A

TIO N

Do not use the Jet Bot on black colored floors.

The Jet Bot may not be able to operate normally.

Do not place any objects within 0.5 m of either side of the Docking Station or within 1 m of the front of the Docking Station.

Make sure the Docking Stations charging contact is not damaged or have any foreign matter on it.

For the very low areas where the Jet Bot may get stuck, set the No- go Zones with the SmartThing App or attach the Boundary Markers to prevent the Jet Bot from getting in.

Do not install the Docking Station in an area with a dark floor.

If the floor around the Docking Station is dark, recharging is hindered.

Move any obstacles that may disturb the Jet Bots movement (such as childrens indoor swing or slides) before cleaning.

Do not use the Jet Bot in a place which is narrower than its turning radius 0.5 m or less.

Before operating the Jet Bot, remove the objects which could break such as glass, a frame, a mirror, and porcelain items so that the Jet Bot works without interruption.

If a brush or a brush cover is not assembled correctly, scratches may occur on the floor, or product malfunction may occur.

Use both hands to carry the product.

Do not place the Docking Station in a place where people pass by frequently, in entrance way or narrow passage.

People may trip over it and be injured, or product damage may occur.

Do not push the Docking Station.

English 9

1_VR8000_EN_00857B-00_AA.indd 9 2021-12-10 3:54:19

P R

E PA

R A

TIO N

In use

WARNING

If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center.

CAUTION

Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet.

The Jet Bot cannot pass over a carpet with fiber longer than 2 cm.

Do not use the Jet Bot on tables or other high surfaces.

There is a risk of damage if it falls.

The Jet Bot may bump into chairs or desk legs, therefore move them away for faster and efficient cleaning.

When the Jet Bot is operating, do not lift it up or carry it to another area.

Do not hold by Driving Wheels of the Jet Bot when carrying it to another area.

Do not put any objects on top of the Jet Bot since it may cause malfunction of the LiDAR sensor or the Jet Bot.

Remove any large papers or plastic bags immediately when using the Jet Bot since they may block the intake.

Do not lie down around the Jet Bot that is running.

Your hair may be caught in the brush, resulting in physical injury.

Do not allow children to play with the Jet Bot.

Make sure hair, fingers, clothes do not get caught in a spin brush or Driving Wheels.

English10

1_VR8000_EN_00857B-00_AA.indd 10 2021-12-10 3:54:19

P R

E PA

R A

TIO N

Do not allow children to sit on the Jet Bot and do not place an object on the Jet Bot.

Leave over 3 cm space from the inner doorstep placed in the entrance. Otherwise, the robot vacuum can ride on it and go outside.

Cleaning and maintenance

WARNING

When the power cord is damaged, contact a service center to get it replaced by a certified repairman.

There is a risk of fire or electric shock.

Please check with a SAMSUNG Electronics service center when replacing batteries.

Using batteries from other products can cause malfunction.

Be careful not to put your finger into the revolving LiDAR sensor. Otherwise, your finger may get injured.

CAUTION

Prevent any damage to the Jet Bot by complying with the following.

Do not clean the Jet Bot by spraying water directly onto it or use a volatile substance such as benzene, thinner, or alcohol to clean it.

Do not disassemble or repair the Jet Bot. This should only be done by a certified repairman.

Always keep the Obstacle Sensor Window and the Cliff Sensor Window clear.

If foreign matter accumulates, sensors may malfunction.

Do not store the Jet Bot in a car.

English 11

1_VR8000_EN_00857B-00_AA.indd 11 2021-12-10 3:54:19

P R

E PA

R A

TIO N

Be careful that the LiDAR sensor is not exposed to a direct light such as sun light, infrared light, etc.

The direct light can affect the performance of the LiDAR sensor.

When carrying the Jet Bot, be careful not to let it drop.

The impact from the drop can affect the operation or performance of the LiDAR sensor.

Do not look at the transmitting part (a laser) of the revolving LiDAR sensor horizontally.

Be careful not to insert a tool such as a chopstick into the revolving LiDAR sensor. Otherwise, the LiDAR sensor may work abnormally or malfunction.

Before cleaning, remove objects which are less than 9 cm height and are lightly on the floor as the Jet Bot can push along them, or the objects can be caught in the Jet Bots spin brush or driving wheels. (Fixed objects can be detected by the Jet Bot when its bumper is pressed and will avoid them.)

If oil such as cooking oil is on the floor, the Jet Bot may become stationary because the floor is slippery. Remove the oil first before cleaning with the Jet Bot.

English12

1_VR8000_EN_00857B-00_AA.indd 12 2021-12-10 3:54:19

P R

E PA

R A

TIO N

REGULATORY NOTICE

1. FCC Notice

WARNING

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:

1 This device may not cause harmful interference, and

2 This device must accept any interference received including interference that cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a different circuit from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help.

English 13

1_VR8000_EN_00857B-00_AA.indd 13 2021-12-10 3:54:20

P R

E PA

R A

TIO N

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

2. IC Notice

The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Open Source License Notice

This device uses open source software. Open Source Licenses are available on the product menu.

Tap Settings > Network > Software Update > Legal Information on the device for more details.

English14

1_VR8000_EN_00857B-00_AA.indd 14 2021-12-10 3:54:20

IN STA

LLA TIO

N INSTALLATION

Installing a Docking Station

Approximately 0.5 m

Approximately 0.5 m

Approximately 1m

1 Connect the provided Battery Charger jack to the rear of the Docking Station.

2 Position the Battery Charger cord into the fixing groove at the rear of the Docking Station.

3 Connect the power cord to the Battery Charger.

4 Place the Docking Station on an even floor and near an electrical outlet and plug it in.

NOTE Install the Docking Station in a place where the floor and wall are level.

If the Battery Charger cord is too long for the installation environment, coil the power cord around the cable management post, then put it in the fixing groove at the rear of the Docking Station.

English 15

1_VR8000_EN_00857B-00_AA.indd 15 2021-12-10 3:54:21

O P

E R

A TIO

N

Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the Product specification.)

1 Open the upper cover of the Jet Bot and remove the white gasket.

OFF ON

2 Remove the yellow gasket attached to the power switch at the side of the Jet Bot and press the power switch to turn the Jet Bot on.

During booting, the Jet Bots Status Indicator turns on with a melody which stops when the booting is complete.

When you turn the Jet Bot on for the first time after purchase, check the SmartThings App connection(refer to p.29-33) and installation of the Docking Station following the voice guide of the Jet Bot.

3 Place the Jet Bot on the Docking Station manually to start charging.

Make sure the charging terminals on the Jet Bot and the Docking Station are aligned.

Status Indicator

4 Check the charging status.

When charging starts, the Status Indicator of the Jet Bot turns on (red, orange, or yellow depending on charging progress), it rises gradually, and changes to green when the charging is complete.

OPERATION

English16

1_VR8000_EN_00857B-00_AA.indd 16 2021-12-10 3:54:23

O P

E R

A TIO

N

Auto charging

The Jet Bot automatically returns to the Docking Station when it completes cleaning, when the Dustbin is full, or when the battery is low to recharge.

Docking (Recharging)

You can return the Jet Bot to the Docking Station while cleaning to recharge.

Press the [ ] on the Jet Bot or use the SmartThings App to select the recharging function.

If the Jet Bot fails to return to the Docking Station for charging, it turns to the Sleep Mode. To cancel the Sleep Mode, press the [ ].

Discharged Jet Bot

Move the Jet Bot manually onto the Docking Station to recharge.

English 17

1_VR8000_EN_00857B-00_AA.indd 17 2021-12-10 3:54:24

O P

E R

A TIO

N

Checking if the docking (recharging) does not work

Check the Docking Stations installation status.

Check whether the Docking Station has been installed in a place where the Docking Station cannot guide the Jet Bot to return.

Check whether the distance between the Docking Station and the Jet Bot is over 5 m.

It may take a longer time for the Jet Bot to return to the Docking Station.

Charge the Jet Bot manually for the following conditions.

When the Docking Station is installed in a corner

When the battery is completely discharged

When the Jet Bot is stuck in an obstacle (e.g., furniture)

When the Jet Bot cannot climb a threshold near the Docking Station. (It should be less than 1.5 cm.)

When the Jet Bots Status Indicator turns red and stays red with the Jet Bot not working

NOTE If the power switch of the Jet Bot is off, the Jet Bot will not charge even if it is docked on the

Docking Station.

Keep the Docking Station on at all times.

If power is not supplied to the Docking Station, the Jet Bot cannot find the Docking Station and cannot automatically recharge.

If the Jet Bot is left detached from the Docking Station, the battery drains naturally.

English18

1_VR8000_EN_00857B-00_AA.indd 18 2021-12-10 3:54:25

O P

E R

A TIO

N

Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot on.

For the normal use of the Jet Bots functions, the SmartThings connection is required.

For downloading and installing the SmartThings App, refer to the SmartThings App(P.29-33).

Basic use

OFF ON

Power on / off

Press the power switch at the side of the Jet Bot to turn the Jet Bot on.

During booting, the Jet Bots Status Indicator turns on with a melody which stops when the booting is complete.

Starting cleaning

Press the [ ] on the Jet Bot to start cleaning in Auto Clean.

Stopping cleaning

Press the [ ] on the Jet Bot to stop operation while cleaning.

When pressing the [ ], the Jet Bot returns to the Docking Station and starts charging.

If the Jet Bot does not operate for 20 minutes after it stops operation, it automatically returns to the Docking Station to recharge.

Sleep Mode

When the Jet Bot is not in operation, press and hold the [ ] to set the Sleep Mode.

In the Sleep Mode, press the [ ] to cancel the Sleep Mode.

OPERATION

English 19

1_VR8000_EN_00857B-00_AA.indd 19 2021-12-10 3:54:26

O P

E R

A TIO

N

Operation status on the LED Status Indicator

Classification Color Meaning

Jet Bot

While operating

Red

Blinking without moving

An error occurs.

Blinking while moving

Auto returning to the Docking Station due to low battery

On Operating stops due to low

battery

While charging

Red, orange, or yellow (depending on charging progress)

While charging

Green Charging is complete.

Violet Software is being updated.

You can set the Cleaning Mode and the Cleaning Functions at the SmartThings App.

During initial charging status, the Status Indicator turns red and slowly blinks for about 20 minutes.

English20

1_VR8000_EN_00857B-00_AA.indd 20 2021-12-10 3:54:26

O P

E R

A TIO

N

Cleaning Functions

Cleaning Functions Operation

Cleaning Methods

Auto Clean: Cleans automatically until the Jet Bot completes cleaning all rooms one time.

Room Clean: You can select a room you want to clean. Spot Clean: You can set a specific area you want to clean.

Cleaning Mode

You can select one out of three modes.

You can set the Cleaning Mode only when the Jet Bot is in Room Clean.

Suction Power

You can select the suction power from Max, Smart or Normal.

When the Jet Bot is in Smart suction power, the Intelligent Power Control Clean work.

Repeat Clean

The Jet Bot cleans repeatedly until its battery is discharged.

After the Jet Bot completes cleaning one time and returns to the Docking Station due to battery shortage, it does not clean again after charging is complete.

Intelligent Power Control Clean

When the Jet Bot detects a carpet during cleaning, it increases its suction power. (Suction Power: Smart only)

You can set the Cleaning Functions, the Repeat Clean or the Cleaning Mode at the SmartThings App.

When the Jet Bot does not have a saved map, it studies cleaning space through Auto Clean function which starts from the Docking Station. After studying the cleaning space, a map is saved. (The map creation is enabled through the SmartThings App only.)

You can edit or delete the map at the SmartThings App.

Room Clean or Spot Clean works regardless of choice sequences of the areas.

English 21

1_VR8000_EN_00857B-00_AA.indd 21 2021-12-10 3:54:26

O P

E R

A TIO

N

Additional functions

Additional functions Operation

Energy-Saving Mode

When charging is complete, the Jet Bot automatically enters the Sleep Mode. While the Jet Bot is docked on the Docking Station, press and hold the [ ] for 7 seconds to set it to the Sleep Mode. To cancel the Sleep Mode, start cleaning or press the [ ] for 7 seconds.

When the Jet Bot is in the Energy-Saving Mode, the power is turned off after charging is complete which means the Wi-Fi reception waiting is not enabled, therefore the Jet Bot cannot be controlled with the mobile app.

Downtime Mode You can set the Jet Bot not to clean within the Downtime at the

Settings.

When Downtime comes, the Jet Bot returns to the Docking Station.

Scheduled Cleaning

You can set the Jet Bot to clean at the Schedule.

If the Jet Bot is detached from the Docking Station at the scheduled time, the scheduled cleaning does not work.

Setting the No-go Zones

When the Jet Bot has saved a map, you can set the Jet Bot not to enter a designated area.

If the Jet Bot does not start cleaning from the Docking Station or the installation place of the Docking Station has been changed, the Jet Bot may clean the set No-go Zones.

When setting the No-go Zones, you cannot include the Docking Station.

You can set the Downtime mode, Scheduled Cleaning or No-go Zones at the SmartThings App.

NOTE

When a Check Notice occurs or when you carry the Jet Bot to another place and start cleaning, the Jet Bot spins left and right at a 30 degree angle to recognize its location before it starts cleaning.

If the Jet Bot cannot recognize its current location, it starts Auto Clean.

The Jet Bot automatically performs a system check and restarts once a week.

English22

1_VR8000_EN_00857B-00_AA.indd 22 2021-12-10 3:54:27

O P

E R

A TIO

N

Attaching Boundary Markers

If Boundary Markers are attached before using the Jet Bot, the Jet Bot can operate safely. You can purchase additional Boundary Markers at a service center.

To prevent the Jet Bot from entering the following areas, attach the Boundary Markers to the floor in a shape with 15 cm space distance.

Boundary Markers

Approximately 15 cm

Approximately 5 cm

Approximately 15 cm

Boundary Markers

Where the raised spot is below 5 cm Where there is a slide, a swing, a flowerpot, a fireplace, any flammable substance or

moisture.

Boundary Markers

1.5 cm Boundary Markers

Where a threshold is above 1.5 cm Where there is a risk of falling such as stairs, porches or guardrails.

English 23

1_VR8000_EN_00857B-00_AA.indd 23 2021-12-10 3:54:28

O P

E R

A TIO

N

Parts diagram

Jet Bot

03

02

01

06

08

05

09

04

07

Top

01 Obstacle Sensor

02 Power switch

03 LiDAR Sensor

04 Dustbin

05 Start/stop button

06 Docking (Recharging) button

07 Status Indicator

08 Docking Sensor Window

09 Upper Cover

04

01

07

02

06

05

03

04

08

09

04

Bottom

01 Charging Pin

02 Brush

03 Brush Cover

04 Cliff Sensor

05 Roller

06 Battery Cover

07 Driving Wheel

08 Spin Brush

09 Brush Cover Lock

Docking Station

03 01

02

01 Charging Terminal

02 Charging Signal Transmitter

03 Power cord groove

English24

1_VR8000_EN_00857B-00_AA.indd 24 2021-12-10 3:54:30

M A

IN TE

N A

N CE

Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot.

Emptying and cleaning the Dustbin

1 Grasp the Jet Bots cover at the groove and lift it up.

2 Hold the Dustbin handle and lift the Dustbin up.

3 Unlock the transparent clip at the side of the Dustbin.

4 Detach the filter from the Dustbin.

5 Remove the dust on the filter and the Dustbin, clean them with water, and dry completely in the shade.

6 Attach the filter to the Dustbin and insert the Dustbin into the Jet Bot. When inserting the Dustbin, grasp the handle and put the Dustbin into both grooves.

MAINTENANCE

English 25

1_VR8000_EN_00857B-00_AA.indd 25 2021-12-10 3:54:32

M A

IN TE

N A

N CE

Cleaning the brush

1 Push the Brush Cover Lock to the right to unlock.

2 Detach the brush cover.

3 Lift up the left side of the brush first and then pull the brush from the groove on the right.

4 Clean the brush.

5 Attach the brush. 6 Attach the brush cover.

English26

1_VR8000_EN_00857B-00_AA.indd 26 2021-12-10 3:54:35

M A

IN TE

N A

N CE

Cleaning the Sensor Window

Wipe the Sensor Window with a soft cloth.

Docking Sensor Window

Obstacle Sensor

Rear Sensor

LiDAR Sensor

Cliff Sensor

Dust Sensor

Cleaning the Driving Wheel

1 Place a soft cloth down first, turn the Jet Bot over, and place it gently on the cloth.

2 Remove foreign matter with a blunt rod or tweezers.

English 27

1_VR8000_EN_00857B-00_AA.indd 27 2021-12-10 3:54:38

M A

IN TE

N A

N CE

Cleaning the Spin Brush

Cover the Spin Brush with a hot steamed cloth for 10 seconds, then wipe the Spin Brush.

When the Spin Brush is very tangled with hair, threads, etc., detach the Spin Brush with a screwdriver while gripping the Spin Brush, and remove the foreign matter. If the Spin Brush is badly damaged, replace it with a new one.

For detailed methods of use and cleaning, refer to the QR code.

English28

1_VR8000_EN_00857B-00_AA.indd 28 2021-12-10 3:54:39

A P

P E

N D

IX

SmartThings App The SmartThings App is only compatible with models that have a Wi-Fi function.

If you do not have a Wi-Fi router, you cannot use the SmartThings App.

Setting up the wireless router

Please refer to the user manual of your wireless router for the settings of the wireless router.

SAMSUNG Jet Bot supports only Wi-Fi 2.4 Ghz.

SAMSUNG Jet Bot supports IEEE 802.11b/g/n and Soft-AP.

IEEE 802.11n is recommended.

SAMSUNG Jet Bot supports only DHCP (Dynamic Host Configuration Protocol). Please make sure that the DHCP server option is activated on your wireless router.

The Jet Bot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the authentication and encryption protocols.

WPA2-PSK/AES is recommended.

Confirm that your router has a unique SSID and password.

The quality of your wireless network connection may be influenced by the surrounding wireless environment.

If your Internet service provider has permanently registered the MAC address (a unique identification number) of your PC or modem, your Jet Bot may not be able to connect to the Internet. Ask your Internet service provider about the procedure to connect an apparatus other than a PC to the Internet.

If your internet service provider requires your ID or password to connect to the internet, your Jet Bot may not be able to connect. If this is the case, you must enter your ID or password when connecting to the Internet.

The Jet Bot may not be able to connect to the Internet because of firewall issues. Contact your Internet service provider to resolve these issues.

Some wireless routers may transmit an abnormal Domain Name Server (DNS) address even if the Internet is not connected. If this occurs, contact the manufacturer of your wireless router and your Internet service provider.

If you still cannot connect to the Internet even after trying the procedure provided by your Internet service provider, please contact an authorized SAMSUNG service center.

If your router is not a Wi-Fi certified product, The Jet Bot may not be able to connect to the Internet.

NOTE

When pressing and holding the [ ] button for 3 seconds, the network status is guided by voice.

Setting Wi-Fi On/Off: Hold the [ ] button down for 7 seconds to switch the Wi-Fi off or on to use again while the vacuum cleaner is on standby or charging.

APPENDIX

English 29

1_VR8000_EN_00857B-00_AA.indd 29 2021-12-10 3:54:40

A P

P E

N D

IX

Downloading the SmartThings App

Download and install the SmartThings App from the markets (Google Play Store, Apple App Store, or SAMSUNG Galaxy Store). To find the app, use the keyword SmartThings.

NOTE

SmartThings is incompatible with some tablets and some mobile devices.

[Android] 7.0 or later (at least 2GB of RAM) is recommended.

If the Smart View function of a Galaxy phone is not supported, you cannot download the SmartThings App.

Some iPads and some mobile devices may not be supported.

[iOS 12.0] or later / iPhone 6s or later is supported.

Visit Play Store or App Store to see if your mobile device is compatible with SmartThings.

The supporting software version of the SmartThings app is subject to change according to the OS supporting policy the manufacturer provides. In addition, as for the SmartThings app or the functions that the app supports, the new application update policy on the existing OS version can be suspended due to usability or security reasons.

The SmartThings app is subject to change without notice to improve usability or performance. As the mobile phone OS version is updated every year, the SmartThings is also updated continually according to the latest OS.

If you have enquiries regarding the items mentioned above, please contact us on st.service@ samsung.com.

Setting up a SAMSUNG account

You must sign in to a SAMSUNG account before using the SmartThings App.

To set up a SAMSUNG account, you can follow the directions provided by the SmartThings App.

Or, if you have a SAMSUNG smartphone, you can add your SAMSUNG account in the setting app of your smartphone. Then, it will automatically sign in to your SAMSUNG account and you can use the SmartThings App.

Registering a device to the SmartThings App

1 Connect your smartphone to your wireless router.

If the smartphone is not connected, turn on the Wi-Fi in the Settings App and select a wireless router you want to connect to.

Set your smartphone to use Wi-Fi only and connect a device.

2 Launch the SmartThings App on your smartphone.

English30

1_VR8000_EN_00857B-00_AA.indd 30 2021-12-10 3:54:40

A P

P E

N D

IX

3 If a pop-up saying that a new device has been found appears, tap ADD NOW.

If the pop-up does not appear, add a device by selecting the Home appliances category Robot cleaner and the Jet Bot to connect.

If you scan the SmartThings QR code attached on the Jet Bot, you can connect to the Jet Bot more easily.

4 [Android] The connection to your device will be progressed automatically.

[iOS] Open the setting app, and select [vacuum]_E30AJT** in the Wi-Fi list.

5 Provide the authentication when you are directed to do so.

6 [Android] The connection to your wireless router will be progressed automatically.

[iOS] Open the setting app, and select the wireless router in the Wi-Fi list.

7 When the product registration is complete, the Jet Bot device card is added.

NOTE

When the Jet Bot cannot be registered to the SmartThings App

Refer to the SmartThings App guide or pop-up messages.

Confirm that the UPnP option of your wireless router is active, and then try the registration procedure again.

Confirm that your wireless router is operating in a wireless mode. If not, change it to the wireless mode and try again.

If you have two or more Jet Bots, turn off the other Jet Bots, and then try to register your Jet Bot again.

Change the name of the wireless router which has the same SSID to be distinguished from each other.

If the Jet Bot and smartphone are not connected to the same wireless router, a response can be delayed depending on the network environment.

When the wireless router is changed, the connection between the Jet Bot and the SmartThings App is disconnected.

After changing the wireless router, register your Jet Bot again at the SmartThings App.

Software Update

When the Jet Bot is charging on the Docking Station, the Jet Bot connects to the server and checks for software updates. If a new software is found, the Jet Bot will automatically download and update it.

If the Status Indicator of the Jet Bot turns violet and stays violet while charging, it means that the Jet Bot is being updated. Please wait until rebooting is complete.

English 31

1_VR8000_EN_00857B-00_AA.indd 31 2021-12-10 3:54:40

A P

P E

N D

IX

Functions of the SmartThings App

Classification Functions Explanation

Monitoring Cleaning Report You can check the result of the last cleaning.

You can check the histories of last 50 cleanings.

Control

Dock You can stop cleaning and have the Jet Bot

return to the Docking Station.

Pause You can stop cleaning or restart cleaning.

Cleaning Mode You can set the cleaning mode you want.

Cleaning Functions

You can set various cleaning functions.

For some functions, you need to create a map first.

For Room Clean and Spot Clean, you can choose only one of them, and the default setting is All (All Rooms).

When the Jet Bot is in the Room Clean or the Spot Clean, it may pass an unselected area to go to the cleaning place or to recharge.

Schedule You can start designated cleaning at the

scheduled time.

Setting

Sound Mode You can set the voice guide to [Voice], [Sound

Effect], or [Mute].

Language The Jet Bot supports 14 languages.

Volume You can control the volume of the voice guide.

Downtime

At the designated time, the Jet Bot stops cleaning and returns to the Docking Station.

You may start cleaning during Downtime.

Find Robot Vacuum The Jet Bot makes a sound so that a user can

find it.

English32

1_VR8000_EN_00857B-00_AA.indd 32 2021-12-10 3:54:41

A P

P E

N D

IX

Classification Functions Explanation

Notice

Cleaning completed When cleaning is complete, you can receive

cleaning completion notice.

Check Notice If the Jet Bot needs to be checked, you can

receive a notice.

Manage maps

No-go Zones

You can set a zone where you do not want the Jet Bot to clean.

You can create maximum 15 zones.

Edit Map

You can divide or combine rooms on the created map.

You can change the name of a room.

Reset Map Reset the saved map.

English 33

1_VR8000_EN_00857B-00_AA.indd 33 2021-12-10 3:54:41

A P

P E

N D

IX

Installation

NOTE

Install the Docking Station in a place where the floor and wall are level.

If the cleaning area is wooden floors, it is best to install the Docking Station along the grain of wooden floors.

If the power switch is off, the Jet Bot will not charge even if it is docked on the Docking Station.

Always keep the Docking Station on.

If power is not supplied to the Docking Station, the Jet Bot cannot find it and cannot automatically recharge.

If the Jet Bot is left detached from the Docking Station, the battery will drain naturally.

Do not attach the Boundary Markers as (——) shape.

The Jet Bot may not detect it and cross the boundary.

Charging

NOTE

If the battery overheats during charging, it may take longer to charge.

When auto charging is not working, do the following:

Turn the power switch (at the side the Jet Bot) off and on again.

Unplug the Docking Stations power plug and then plug it back on.

Unplug the Docking Station, and then check whether there is any foreign matter on the charging pins and clean charging pins of the Jet Bot and the Docking Station with a dry cloth or rag.

Check for any obstacles such as reflective objects, chairs, etc. near the Docking Station.

Notes and cautions

English34

1_VR8000_EN_00857B-00_AA.indd 34 2021-12-10 3:54:41

A P

P E

N D

IX

If the Jet Bot is left detached from the Docking Station, the battery will drain naturally.

Try to keep the Jet Bot being charged on the Docking Station. (However, turn off the power switch and leave the Docking Station unplugged when planning to leave the house for long periods of time by going on a business trip or vacation, etc.)

Using

NOTE

The Jet Bot may get caught on thresholds of entrance door or veranda, etc. during cleaning.

To restart operation, shut off the power switch, move the Jet Bot to an area where it can move easily, and then turn on the power again.

In a dark area, the Jet Bot may not recognize an object.

Before cleaning, remove obstacles on the floor.

The Jet Bot cannot completely clean areas which it cannot enter, such as small space between the corner, between the sofas or walls, etc.

Please use another cleaning tool to clean them regularly.

The Jet Bot cannot vacuum clumps of dirt, so some may remain on the floor after cleaning.

Please use another cleaning tool to clean them regularly.

After turning the Jet Bot off, wait for a while and then turn it on for a normal rebooting.

English 35

1_VR8000_EN_00857B-00_AA.indd 35 2021-12-10 3:54:41

A P

P E

N D

IX

Cleaning and maintenance

NOTE

If you washed the Dustbin and filter with water

Dustbin: Completely wipe out the water.

Filter: Completely dry it in the shade before use.

CAUTION

Watch your fingers when attaching or detaching the filter, since they may get stuck in the Dustbins intake.

To avoid blockages by foreign matter, do not let the Jet Bot vacuum up toothpicks, cotton swabs, etc.

If it is difficult to remove foreign matter from the brush, contact an authorized SAMSUNG service center.

Since the brush sweeps dirt up from the floor during cleaning, foreign matter such as a thin and long thread, long hair, etc. may get caught in it. For the best cleaning results, check and clean it regularly.

Turn off the Jet Bot before cleaning or maintenance work.

If a brush or a brush cover is not assembled correctly after the maintenance work, scratches may occur on the floor, or product malfunction may occur. Therefore, assemble them correctly by checking the maintenance method.

English36

1_VR8000_EN_00857B-00_AA.indd 36 2021-12-10 3:54:41

A P

P E

N D

IX

Battery usage

NOTE

When you purchase a battery, check the SAMSUNG logo ( ) attached on the battery and the model name, then contact a service center.

This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes.

Do not disassemble or modify the battery.

Do not throw the battery out in fire or heat it.

Do not connect any metallic object to the charging contacts (+, -).

Store the battery indoors (at 0 C~40 C).

If the battery malfunctions, do not disassemble it yourself. Contact your nearest SAMSUNG service center.

As the battery is used over a length of time, the battery charging time and usage time decreases. In this case, contact a service center and replace it with a new battery.

Do not disassemble the battery yourself and make sure short circuit of +, — poles does not occur.

When battery leak occurs, make sure it does not touch your skin or eyes.

English 37

1_VR8000_EN_00857B-00_AA.indd 37 2021-12-10 3:54:42

A P

P E

N D

IX

Corrective measures before reporting a problem

1 The Status Indicator turns red and blinks with a voice guide.

2 Turn off the power switch and check the instructions below and take appropriate actions.

3 When turning the Jet Bot on by pressing the power switch, the Status Indicator turns white.

Voice Guide Checklist

It is difficult surroundings for me to work. Please move me to another place.

The Jet Bot is caught, stuck or trapped while moving around.

Turn off the power switch and move the Jet Bot to another area.

Detach the brush at the bottom and remove a foreign body from the brush.

Foreign matter caught in the brush

Turn off the power switch and remove the foreign matter from the brush.

Check the left wheel. If a foreign body is tangled, remove it.

Foreign matter caught in the left Driving Wheel

Turn off the power switch and remove the foreign matter from the left Driving Wheel.

Check the right wheel. If a foreign body is tangled, remove it.

Foreign matter caught in the right Driving Wheel

Turn off the power switch and remove the foreign matter from the right Driving Wheel.

Something is wrong with the Bumper Sensor. Please check the bumper on the front.

Bumper Sensor needs to be checked.

Turn off the power switch and turn it back on.

When the Status Indicator remains in red color and blinks, check if there’s any small foreign matter between the bumper and the main body. If there is, remove the foreign matter.

Please wipe the black window on the front with a soft cloth.

Foreign matter accumulated on the Obstacle Sensor Window.

Turn off the power switch and clean the Obstacle Sensor Window at the front with a soft cloth.

Something is wrong with the Cliff Sensor. Please wipe the 4 small black windows at the bottom with a soft cloth.

Foreign matter accumulated on the Cliff Sensor

Turn off the power switch and clean 4 Cliff Sensor Windows at the bottom with a soft cloth.

Before cleaning, insert a Dustbin. Dustbin is not inserted.

Detach the Dustbin and insert it again.

You can find details of the check at the SmartThings App.

When the Jet Bot is turned off and on again, it starts newly in the Auto Clean mode.

English38

1_VR8000_EN_00857B-00_AA.indd 38 2021-12-10 3:54:42

A P

P E

N D

IX

Troubleshooting

Symptom Checklist

The Jet Bot is not working at all.

Check if the power switch is on. Check if the Status Indicator is on. Check if the Jet Bot’s battery is depleted.

When the Jet Bots Status Indicator turns red and stays red, place the Jet Bot manually on the Docking Station to charge it.

When you manually charge the Jet Bot due to complete discharge of its battery, the buttons on the Jet Bot do not work. When charging is partially complete (about 10-20 minutes later), the Status Indicator is on and the buttons work again.

The Jet Bot has stopped during cleaning.

When the Jet Bots Status Indicator turns red and stays red, place the Jet Bot manually on the Docking Station to charge it.

When the Jet Bot is immobilized by an obstacle such as a cord, obstacles, threshold, a raised spot, etc., pick it up and move it away from the obstacle.

If any fabric or string is caught in a Driving Wheel, turn off the power switch and remove the fabric or string before using it again.

Check whether the No-go Zones are set.

Suction power is weak.

When there’s too much dust in the Dustbin, suction power may get weakened. Turn off the power switch and empty the Dustbin.

If the brush at the bottom of the Jet Bot is blocked by foreign matter, turn off the power switch and remove foreign matter from the brush.

When noise suddenly increases, turn off the power switch and empty the Dustbin.

The Jet Bot cannot find the Docking Station.

Check if there’s a power failure or whether the power plug is unplugged.

Remove any obstacles around the Docking Station that may prevent the Jet Bot from returning to the Docking Station.

When there’s foreign matter on the charging terminals, charging can be affected. Clean the foreign matter off the terminals.

English 39

1_VR8000_EN_00857B-00_AA.indd 39 2021-12-10 3:54:42

A P

P E

N D

IX

Symptom Checklist

The Jet Bot does not detect the Boundary Marker and crosses the boundary.

Make sure the Boundary Markers are attached as ( ) shape at 15 cm before the locations where the Jet Bot should not cross.

The Jet Bot suddenly cleans diagonally.

Check if the Docking Station is installed along the grain of wooden floors or tiles.

The Jet Bot may clean in a diagonal direction if it is moving to another area using the shortest route. It may also move at a diagonal if it did not make contact with an obstacle at a right angle, if it was charged in a skewed direction at the Docking Station, or If the floor material is wooden or tile.

Jet Bot does not clean some places.

Check whether the Docking Station is installed in a narrow passage or near a room door and move it to another place.

If the Docking Station is installed in a narrow passage or near a room door, the Jet Bot cannot pass through the passage or the door.

Check whether the places the Jet Bot does not clean are set as No-go Zones.

The Jet Bot cannot find a room.

If the Jet Bot does not start cleaning from the Docking Station, or if the Docking Station is reinstalled to a new position of 45 degree or 1 m or more from the previous installed place, the Jet Bot cleans all areas, which is not based on the created map.

Start cleaning from the Docking Station.

When the Jet Bot creates a map and the Jet Bot starts cleaning, make sure the Jet Bot starts operating parallel to the wall.

Remove obstacles within 0.5 m of the left and right side and 1 m of the front side of the Docking Station.

The map which the Jet Bot has created is different from the saved map and the map is also drawn askew.

The Jet Bot does not detect and crosses No-go Zones.

If the Jet Bot does not start cleaning from the Docking Station, the set No-go Zones function does not work. Therefore, start cleaning from the Docking Station to use the function.

English40

1_VR8000_EN_00857B-00_AA.indd 40 2021-12-10 3:54:42

A P

P E

N D

IX

Symptom Checklist

The Intelligent Power Control function works on a normal floor.

Check whether the floor is not even and then the Jet Bot works with its body a bit lifted up.

Check whether there are any foreign matter on the Cliff Sensor which is at the bottom of the Jet Bot.

Check whether the floor color is dark.

The Intelligent Power Control function does not work.

When the Jet Bot cleans a carpet with short fiber and bright color, it may recognize the carpet as a floor and then the Intelligent Power Control function may not work.

SmartThings App cannot be installed.

SmartThings App operates on Android OS 7.0 or later, iOS 12.0 or later.

The supporting OS version for the SmartThings App may change later.

For rooted smart devices, standard installation and use will not be guaranteed.

I have installed the SmartThings App, but the Jet Bot fails to be connected.

Connect the Jet Bot to a wireless router by referring to the SmartThings App of the user manual.

I fail to log into the SAMSUNG account.

Check your ID and password on the screen of the SAMSUNG account.

During product registration, the wireless router I want to connect cannot be searched.

Cancel the product registration, run the SmartThings App again, and try the product registration again.

During product registration, the password of the connecting wireless router is not input correctly.

Cancel the product registration, run the SmartThings App again, and try the product registration again.

Press and hold the wireless router you want to connect on the network list, and delete the network to initialize the password.

During product registration, [   ] button is pressed and held as instructed but the next step does not appear.

Press the [ ] button until you hear it beep. If the next step does not appear within several seconds,

press the [ ] button one more time.

English 41

1_VR8000_EN_00857B-00_AA.indd 41 2021-12-10 3:54:43

A P

P E

N D

IX

Symptom Checklist

A message of the product registration failure appears.

Try the product registration procedure again by referring to the pop-up messages.

Please refer to the Setting up the wireless router in the user manual.

Please refer to the steps for completing the product registration in the user manual section «Adding a device to the SmartThings App».

When the product registration fails repeatedly, restart the SmartThings App and try the product registration.

All users should use the SAMSUNG account issued by the country which launches the product.

(Applicable to iOS only) During product registration, the AP password 1111122222 is not input correctly.

Press and hold the [vacuum]_E30AJT** on the network list and delete the network to initialize the password.

The Jet Bot is not connected to Wi-Fi.

Check the setting status of the wireless router.

Even though the Jet Bot is connected to a smartphone without a problem, the Jet Bot does not work with the smartphone.

Turn off the SmartThings App and then run it again, or disconnect the smartphone from the wireless router and then connect it again, or turn off the power supply of the Jet Bot, turn it on, wait for a minute or longer, and then run the SmartThings App again.

The Jet Bot on the SmartThings App fails to start.

Check if the Jet Bot is offline status on the SmartThings App.

Connect the wireless router to Jet Bot again by referring to the SmartThings App on the manual.

The ‘Offline’ message of the Jet Bot appears on the SmartThings App though the Jet Bot’s registration has completed without a problem.

Close the SmartThings App and then run it again. Check whether there is an internet connection problem

of the wireless router. Especially, a firewall may interrupt standard operation.

English42

1_VR8000_EN_00857B-00_AA.indd 42 2021-12-10 3:54:43

A P

P E

N D

IX

Symptom Checklist

The Offline message of the Jet Bot appears on the SmartThings App during normal operation of the App.

If the Jet Bot is distant from a wireless router, connection cut may occur.

Close the SmartThings App and restart the App. If the connection cut occurs repeatedly, try the product

registration again. When the SSID/password of a wireless router is

changed, try the product registration again. Check whether the Jet Bot is in the Sleep Mode. Press

the [ ] to cancel the Sleep Mode.

A map cannot be saved.

To create a map, you need to register the device first and then start creating a map with the Smarthings App.

When the Jet Bot starts cleaning from the Docking Station and completes cleaning one time in Auto Clean, a map is saved.

When controlling with a smartphone, a response is delayed.

If the Jet Bot and the smartphone are not connected to the same wireless router, a response can be delayed depending on the network environment.

English 43

1_VR8000_EN_00857B-00_AA.indd 43 2021-12-10 3:54:43

A P

P E

N D

IX

Open Source Announcement

The software included in this product contains open source software.

To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL etc), please visit http://opensource.samsung.com/ and search by model name.

It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required.

The following URL http://opensource.samsung.com/opensource/VR9500_0/seq/0 leads to open source license information as related to this product. This offer is valid to anyone in receipt of this information.

How to reset to the factory default

Turn the Jet Bot on and press and hold the [ ] + [ ] for 7 seconds. Then the status indicator turns white and blinks, and the Jet Bot starts factory default setting.

When the factory default setting is complete, the Jet Bot automatically restarts.

After the factory default setting, the device status on the SmartThings App changes to offline status.

Press and hold the Delete device on the SmartThings App and delete the product.

After that, register the product with a mobile device.

English44

1_VR8000_EN_00857B-00_AA.indd 44 2021-12-10 3:54:43

A P

P E

N D

IX

Product Specification

Classification Items VR30T80**** series

Mechanical specifications

Weight 3.4 kg

Cleaning method LiDAR location recognition

Button method of the Jet Bot Touch type

Electrical specifications

Power consumption of the Jet Bot

60 W (Spot Clean)

Battery specification Lithium-ion 21.9 V / 52.56 Wh

Cleaning part

Charging type Auto charging / Manual charging

Cleaning Functions Auto Clean, Room Clean, Spot Clean

Additional functions Energy-Saving Mode, Downtime Mode,

Scheduled Cleaning, No-go Zones setting

Charging time About 240 minutes

Cleaning time (Based on a

wooden floor)

Max About 60 minutes

Smart About 60-90 minutes

Normal About 90 minutes

Wi-Fi Frequency range 2412 — 2472 MHz

Transmitter power(Max) 20 dBm

Charging and cleaning time may differ depending on the conditions of use.

You can set the Downtime, the Scheduled Cleaning, the No-go Zones at the SmartThings App.

[Unit : mm]

Height 99.8

W idth 350 Depth 350

Height 105

W idth 154

Depth 186

English 45

1_VR8000_EN_00857B-00_AA.indd 45 2021-12-10 3:54:44

If you have any questions or comments relating to Samsung products,

please contact the SAMSUNG customer care center.

Country Customer Care Center Web Site

CANADA 1-800-SAMSUNG (726-7864) 1-844-SAM-PAYS (726-7297)

www.samsung.com/ca/support (English) w