Проектор christie cp2215 мануал на русском - Большая энциклопедия инструкций и руководств

Manuals
Brands
Christie Manuals
Projector
CP2215
User manual

Contents
Table of Contents
Troubleshooting
Bookmarks

Quick Links

CP2215

U s e r M a n u a l

020-101225-01

Downloaded from ProjectorsManual.com Manuals

Related Manuals for Christie cp2215

Summary of Contents for Christie cp2215

Page 1
CP2215 U s e r M a n u a l 020-101225-01 Downloaded from ProjectorsManual.com Manuals…
Page 2
Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material.
Page 3: Table Of Contents

Adjust Horizontal Boresight ……..23 CP2215 User Manual 020-101225-01 Rev.
Page 4
Adjust Lamp Power ……….42 CP2215 User Manual 020-101225-01 Rev.
Page 5
Calibrate the Internal Light Meter ……..55 CP2215 User Manual 020-101225-01 Rev.
Page 6
Verify 3D Cinema Content ……… . 70 CP2215 User Manual 020-101225-01 Rev.
Page 7
Power Requirements ……….89 CP2215 User Manual 020-101225-01 Rev.
Page 8
Accessories ……….93 CP2215 User Manual 020-101225-01 Rev.
Page 9: Installation And Setup

Only accredited Christie technicians who are knowledgeable about the hazards associated with high-voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are authorized to assemble, install, and service the projector. In addition, only Christie accredited personnel are authorized to perform security procedures such as marriage.
Page 10: Ac/Power Precautions

• Disconnect projector from AC before opening any enclosure. Failure to comply could result in death or serious injury. • The dedicated earth wire can only be installed by a Christie accredited service technician or an electrician. The protected earth wire must be green/yellow 12 AWG minimum.
Page 11: Lamp Precautions

Christie Protective Clothing Safety Kit (P/N: 598900-095). Recommended protective clothing includes, but may not be limited to a polycarbonate face shield, protective gloves, and a quilted ballistic nylon jacket or a welder’s jacket. Christie’s protective clothing recommendations are subject to change. Any local or federal specifications take precedence over Christie recommendations.
Page 12: Projector Components — Rear

2. Position the projector so it is centered and parallel with the theatre screen. If space is limited, aim the projector slightly off-center and use lens offset to center the image on the screen. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014)
Page 13: Adjust Tilt And Level The Projector

The Touch Panel Controller on page 1. Loosen the mounting arm on TPC. 2. Fit the TPC mounting arm over the ball joint (A) located on the rear panel of the projector. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 14: Connect The Exhaust Duct

1. Align the duct with mounting holes on the side of the projector. 2. Hold the duct in position and secure it to the projector with 4 M5 screws. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 15: Install The Lens

4. Insert the lens straight into the lens mount opening without turning. Magnets inside the lens mount help position the lens. 5. Insert and tighten the 2 lens mount hex screws shipped separately with the projector. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 16: Install The Lamp

6. Move the lens clamp to the locked position. Install the Lamp This procedure should only be performed by a Christie accredited technician. High-pressure lamp may explode if improperly handled. Always wear approved protective safety clothing whenever the lamp door is open or when handling the lamp. Failure to comply results in death or serious injury.
Page 17
Insert your right index and middle finger through the back of the reflector and guide the lamp onto the cathode clamp. Be careful not to hit the lamp against the reflector. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 18: Connect Devices To The Projector

Projector Connections and Status LEDs Item Description Indicates the status of the regulator. A solid blue LED indicates the regulator is enabled. If the LED is not illuminated, the regulator is not enabled. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 19
A Simple Contact Closure Interface (SCCI) port that uses a simple dry contact closure to turn the lamp on or off or open or close the douser. Connects the projector to a computer. Connects the projector to Christie or third-party automation equipment. Utilizes the Christie- proprietary protocol. Connects the projector to a 10Base-T/100Base-TX Ethernet connection.
Page 20: Connect The Projector To A Computer

Item Description Connects the projector to external input and output devices, such as the Christie ACT. Connects the projector to non-cinema video and graphics sources. These are single-link ports for single-link cables and connectors. The connectors can be used together as a twin-link DVI port.
Page 21: Connect Devices To The Scci Port

+5V standby Current limited 5VDC supply. Lamp off Projector power on and lamp is off. +5V standby Current limited 5VDC supply. Douser closed Close douser. Douser open Open douser. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 22: Connect Power

The open-collector Health Output (PIN circuit only draws power when a failure occurs or an interlock is activated. Connect Power The dedicated earth wire can only be installed by a Christie accredited service technician or an electrician. The protected earth wire must be green/yellow 12 AWG minimum. See Power Requirements on page 89 for power requirements.
Page 23: Turn The Projector On

2. Select a user name in the Username list. To view the permissions associated with each account User Access Permissions on page 3. Enter your password. 4. Tap Login. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 24: Activate Marriage

The baud rate of the serial port. The default is 115200. Enable SNMP Enables SNMP. SNMP V2 / SNMP V3 The SNMP protocol type. Contact Christie technical support for the SNMP V3 user ID and password. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014)
Page 25: Add The Lamp Information To The Lamp History

LampLOC to adjust the lamp position when you install a new lamp in the projector. After making the adjustment, the lamp is well-centered and at the correct distance from the illumination system. 1. Turn the lamp on and open the douser. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 26: Adjust The Image To Fit Your Screen

7. With the framing test pattern displayed, re-check projector leveling so the top edge of the image is parallel to the top edge of the screen. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 27: Play Content

To play encrypted cinema content, an Integrated Media Block (IMB) is required. Contact your Christie sales representative for more information. If you install the optional IMB, you can connect the projector to a network-attached storage (NAS) or direct attached storage (DAS) device.
Page 28
Downloaded from ProjectorsManual.com Manuals…
Page 29: Adjust The Image

If your installation does not allow the image to be centered with the center of the screen, move the entire projector in the direction of lens travel. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 30: Adjust Vertical Boresight Angle

Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance. Failure to comply could result in death or serious injury.
Page 31: Adjust Horizontal Boresight

Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance. Failure to comply could result in death or serious injury.
Page 32
Once both cross hairs are in focus lock the set screw for right boresight. 9. Repeat Steps 5 to 7 for the left side. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 33: Adjust Dmd Convergence

Normally, the three colors should overlap precisely to form pure white lines throughout the image and one or more poorly converged individual colors may appear adjacent to some or all of the lines. Contact your Christie accredited service technician to correct DMD convergence issues.
Page 34: Color Calibration

Side Masking – Movable flat black panels or curtains are installed on each side of the screen. You close the curtain for flat images, and open the curtain and zoom for scope images. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014)
Page 35: Calibrate Screen Brightness (Fl)

1. Turn the lamp on and allow it to operate for 20 minutes. 2. On the touch pad controller, tap Menu > Administrator Setup > Foot Lamberts Calibration. 3. Complete the Foot Lamberts Calibration wizard. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 36
Downloaded from ProjectorsManual.com Manuals…
Page 37: Access The Projector And Run Diagnostics

This starts the projector, turns the lamp on, and opens the douser. When using the emergency start button, you cannot change channels. The Main Screen Use the Main screen of the Touch Panel Controller (TPC) to access power, lamp, douser, channel, and test pattern settings. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 38: Log On To The Projector

Power and lamp are off. Power saving mode. Flashing yellow or green Cool down mode Moving to standby mode. Power is on and the lamp is off. The lamp can be struck. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 39: View The Status Of Projector Components

To adjust the width of a column in the left pane, tap and drag the column border. When you close the Status window, the column widths return to their default size. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 40: Respond To Alarms

Acknowledge. To view all alarms, tap Menu > Status > All Alarms in the left pane. Run the Projector Interrogator The interrogator captures diagnostic information that you can use to assist Christie service personnel diagnose and correct projector issues. To access the Interrogator menu, you need Operator, Administrator, or Service permissions.
Page 41: View Smpte Errors

1. Tap Menu > Diagnostics > Server Test. 2. Enter the location of the metafile in the Meta File URI field. — or — Enter the location of the subtitle file in the Subtitling URI field. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 42: Turn The Projector Off

If you are servicing the projector, or removing the outer skins, disconnect the projector from AC power and turn the breaker off. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 43: Manage The Dlp

1. Insert a USB flash drive in the USB port on the side of the touch panel controller (TPC). If you do not insert a USB flash drive, the ICP certificate is saved to the FTP root directory. 2. Tap Menu > Diagnostics > DLP Management. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 44: Disable The Icp Signature Test

To re-enable the ICP signature test, clear the Bypass Signature Test check box. Indicate an LD is Installed 1. Tap Menu > Administrator Setup > Content Devices Configuration. 2. Tap LD Installed. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 45: Work With Channels

The Measured Color Gamut Data (MCGD) file used to calculate target color processing. Target Color The Target Color Gamut Data (TCGD) value. This option is not available when Use PCF is selected in the Config 1 screen. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 46
Automatically performs scan type detection. This feature is supported Detection for PIB inputs only. Use PCT Applies Christie Pureformity Color Technology (PCT) to the channel. PCT File Identifies the Christie Pureformity Color Technology (PCT) file associated with the channel. HDMI EDID Type…
Page 47: Activate A Channel

4. Tap Default Current Channel to restore the default settings to the selected channel. — or — Tap Default All Channels to restore the default settings to all channels. 5. Tap OK. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 48: Change The Channel Icon

3. To remove a channel from the Preferred Channels pane, tap and drag a channel from the Selected Channel Buttons (Drag and Drop) pane to the recycle bin in the bottom right corner. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 49: Manage Lamp Information

2. Select a lamp file in the Current Lamp File list. 3. Modify the lamp file settings. 4. Tap Save. To revert your changes, tap Revert before you tap Save. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 50: Enable Or Disable Liteloc On A Lamp File

Expiry Date To receive an alarm when the lamp reaches its operational limit: 1. Tap Menu > Administrator Setup > Preferences. 2. Tap Lamp Expiry in the Alarm Triggers area. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 51: Add A Lamp To The Lamp History

The number of hours the lamp has operated before installation. 4. Tap Save. Verify Current Lamp Intensity Tap Menu > Advanced Setup > Lamp Power/LiteLOC Setup. The current light intensity value appears in the Intensity field. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 52
Downloaded from ProjectorsManual.com Manuals…
Page 53: Manage Projector Setting Files

Use screen files to define the size of the display panel and image cropping. You can assign the same screen file to multiple input devices. 1. Tap Menu > Advanced Setup > Screen File Setup. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 54: Modify A Screen File

8. Record the red chromaticity value. 9. Repeat steps 5 to 7 for the green, blue, white, and black chromaticity measurements. Select the test pattern that matches the color you are measuring. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 55: Modify A Mcgd File

1. Tap Menu > Advanced Setup > TCGD File Setup. 2. Select a TCGD file in the Current Target (TCGD) File list. 3. Modify the TCGD file settings. 4. Tap Save. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 56: Create A New Ils File

1. On the main screen of the TPC, tap a channel in the Preferred Channels pane. 2. Tap the Lens Adjust icon. 3. Select Enable Automatic ILS. 4. Tap OK. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 57: Reset Ils File Settings

3. Select Reset on Startup in the Intelligent Lens System area. Complete a Full Lens Calibration 1. Tap Menu > Advanced Setup > Lens Setup. 2. Select a lens in the Primary Lens list. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 58: Reset The Ils And The Lens Position

1. Tap Menu > Advanced Setup > Lens Setup. 2. Select a lens in the Primary Lens list. 3. Tap Quick Reset in the Intelligent Lens System area. 4. Tap Yes. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 59: Work With The Scheduler

2. Tap and drag the scroll bar to view the available dates. 3. Tap the event you want to edit. 4. Tap Edit. 5. Adjust the settings for the event. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 60: Delete A Scheduled Event

3. Tap Yes. Turn the Scheduler Off You need Administrator or Service permissions to complete this procedure. 1. Tap Administrator Setup > Scheduler. 2. Tap to clear the Enable Scheduler checkbox. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 61: View And Modify Projector Settings

You need Administrator or Service permissions to complete this procedure. 1. Tap Menu > Administrator Setup > Time Setup. 2. Adjust these settings: Field Description Time Zone The time zone where the projector is installed. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 62: Modify Projector Communication Settings

The baud rate of the serial port. The default is 115200. Enable SNMP Enables SNMP. SNMP V2 / SNMP V3 The SNMP protocol type. Contact Christie for the SNMP V3 user ID and password. Management IP The IP address where SNMP information and notifications are sent.
Page 63: Access A Network Device

URL field and enter the URL for the network device. 6. Tap Enter. Access a Network Device Tap Menu > Network Devices > Christie ACT To interact with the device tap in the top right corner of the window.
Page 64: View Microsoft Windows Explorer

1. Tap Menu > Advanced Setup > Lens Setup. 2. Select a lens type in the Primary Lens list. 3. Tap the Launch Dialog icon and enter the lens serial number. 4. Tap Enter. 5. Tap Save. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 65: Manage User Accounts

Change a User Account Password or Permissions You need Administrator or Service permissions to complete this procedure. 1. Tap Menu > Administrator Setup > User Accounts. 2. Tap a user name in the Username list. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 66: Delete A User Account

You need Administrator or Service permissions to complete this procedure. 1. Tap Menu > Administrator Setup > User Accounts. 2. Tap a user name in the Username list. 3. Tap Delete. 4. Tap Yes. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 67: Backup, Restore, And Upgrade Projector Files

Upgrades system components that are newer or older than Components Only the currently installed version. ICP Only Force Install Forces an ICP install regardless of what current version is installed. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 68: Back Up Projector Settings And Information

1. Tap Menu > Service Setup > File Management. 2. Select a file type to restore in the Select type list. 3. Tap Reset Defaults. 4. Tap Yes. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 69: Move Files To The Projector

2. Select a file type in the File Type list. 3. Tap and drag a file from the Projector Files pane to the trash can icon. 4. Tap Yes. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 70
Downloaded from ProjectorsManual.com Manuals…
Page 71: Test Patterns

) icon in the task bar. 2. Tap All Test Patterns. 3. Double-tap a test pattern in the Preferred Test Patterns pane to turn it on. 4. Tap Full Screen (Ignore screen file settings). CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 72
Downloaded from ProjectorsManual.com Manuals…
Page 73: View 3D Content

3D OFF = Low logic level = O/P transistor OFF CONN_SYNC+ SYNC from projector. To projector GPO collector. Compatible with current projector GPIO requirements and restrictions. (24VDC max, 50mA max) CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 74: Hardware Setup

1. Tap Menu > Advanced Setup > High Frame Rate 3D File Setup. 2. Select a 3D frame rate file in the Current 3D File list. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 75
The degree of reference between the left and right sync output. Values between -180 and 180 are accepted. Tap Launch Dialog to enter the phase delay value. 4. Tap Save. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 76: Edit The Default 3D Lamp File

4. Tap Config 2 in the left pane and edit these settings: a. Select 3D Onsite in the Measured Color list. If this option is not available, see Define a Measured Color Gamut Data File on page xiv-68. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 77: Edit The 3D Scope 2048 X 858 Channel

Select 6:2 in the Frame Rate N:M list. c. Select Left (L1R1 L2R2) in the L/R Display Sequence list. d. Select True in the 3D Sync Polarity list. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 78: Display 3D Diagnostic Test Patterns

Tap Menu > Channel Setup on the projector touch pad controller (TPC). b. Select a 3D channel in the Channel Name list. c. Select Inverted in the 3D Sync Polarity list. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 79: Troubleshooting

Troubleshooting This section provides information and procedures for resolving common projector issues. If you cannot resolve a projector issue, contact Christie support n order that a support representative can better assist you, have the model and serial number of your projector ready. For contact information see the back cover of this document.
Page 80: Lamp Functionality

If you do not hear a clicking noise, there might be a problem with the ballast. Contact a Christie accredited service technician to resolve the issue. • If you hear a brief clicking noise, but the lamp does not ignite, replace the lamp.
Page 81
Increase the lamp power. Lamps which are near end of service may not operate reliably at a lower power setting. • Fold mirror misalignment. Contact your Christie accredited service technician to resolve the issue. • Integrator rod misalignment. Contact your Christie accredited service technician to resolve the issue.
Page 82
If you have resized the image, adjust the resizing settings until the entire image is visible and centered. Inconsistent picture quality Verify the quality of the signal from the input source. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 83: Maintenance

Keep repeating this cycle until the coolant is removed. Then lightly moisten a new tissue with deionized water and blot the area again. Use a dry tissue to dry the area. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014)
Page 84: Clean The Radiator Filter

4. Remove the top lid. 5. Reach into the projector and then loosen the first service panel screw. 6. Open the integrator rod access door and loosen the second service panel screw. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 85: Inspect The Lamp

• Dust-free blower — filtered dry nitrogen blown through an anti-static nozzle. • Dust-free lens tissue, such as Melles Griot Kodak tissues (18LAB020), Opto-Wipes (18LAB022), Kim Wipes or equivalent. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 86: Clean The Lens

• EXPLOSION HAZARD. Wear authorized protective clothing whenever the lamp door is open and when handling the lamp. Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie. Failure to comply results in death or serious injury.
Page 87: Remove The Existing Lamp

Handle the box with extreme caution — the lamp is hazardous even when packaged. Dispose of lamp box according to local area safety regulations. Failure to comply could result in death or serious injury. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 88: Install The New Lamp

4. Hold the anode end of the new lamp in your left hand and angle it up through the hole in the back of the reflector assembly. Insert your right index and middle finger through the back of the CP2215 User Manual 020-101225-01 Rev. 1 (01-2014)
Page 89
The number of hours the lamp has operated before installation. 14. Tap Save. 15. Tap Next. 16. Align the lamp. See Align the Lamp with LampLOC on page 17. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 90: Inspect The Card Cage Filter

Maintenance Inspect the Card Cage Filter Use only high efficiency Christie approved filters. Never operate the projector without the filter installed. You should check the condition of the card cage air filter monthly. Clean or replace the card cage air filter sooner if you are operating the projector in a dusty or dirty environment.
Page 91: Replace The Lens

9. Secure the lens clamp by rotating it clockwise. 10. Tighten the lens mount cap screws for added stability. 11. Remove the lens cap from the front of the lens. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 92
Downloaded from ProjectorsManual.com Manuals…
Page 93: Specifications

Specifications This section provides detailed specifications for the Christie CP2215 projector. Due to continuing research, specifications are subject to change without notice. Display Panel Resolution and Refresh Rate Item Description Pixel format (H x V square pixels) 2048 x 1080 Processing path 23.97 — 240Hz…
Page 94: White Point

9-pin subminiature D, female Bit Rate 115,200 (default) bps Flow Control Hardware (RTS/CTS) Data Format 1 start bit, 8 data bits, 1 stop bit, no parity Communication Protocol Christie Serial Protocol CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 95: Rs232-Icp

Output 1 – Projector Health (high = health ok) Connector 9-pin subminiature D, female Input Current 5mA nom., 50mA max. Input Forward Voltage Drop 1.1V nom., 1.4V max. (@ 5mA) CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 96: 3D Terminal

USB Device Standard Size (Series “B”) Maximum Bit Rate 12 Mbps Communication Protocol Texas Instruments Proprietary MALM Terminal Item Description Interface 3.3V CMOS Connector 9-pin subminiature D, female Number of I/O Lines 4 GPIO CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 97: Touch Panel Controller

Discrete switch above the power inlet cord(s) Current Rating of AC Input 8A (Outlet is IEC-320-C13) Supported UPS Type Universal 100-240VAC Power Consumption 270 W typical (@ 100 VAC with a power factor of 0.9) CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 98: Lamp

55 kg (121 lbs) Weight Shipping (includes packaging) 65 kg (143 lbs) Rotation about projection axis ± 15 degrees maximum Operating Position Tilt of projection axis from horizontal ± 15 degrees maximum CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 99: Regulatory

The product is designed to comply with the rules and regulations required for the product to be sold in various regional markets, including: USA, Canada, European Union, Argentina, Australia, New Zealand, Kuwait, China, Korea, Japan, India, Mexico, Ukraine, Russia, South Africa, and Saudi Arabia. CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 100: Environment

Humidity (non-condensing) 20% to 80% Altitude 0 — 3000 meters Maximum ambient temperature 35°C Non-Operating Environment Item Description Temperature -25°C to 65°C (-13°F to 149°F) Humidity (non-condensing) 0% to 95% CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 101: Accessories

Replacement Lamps CDXL-14M (003-003066-XX) CDXL-18SD (003-002742-XX) CDXL-20SD (003-001976-XX) CDXL-23S (003-004769-XX) Replacement Paper Air Filter 003-002311-XX Replacement Washable Air Filter 003-004655-XX Liquid Coolant Fill Service Kit 003-001837-XX Extractor Adaptor Kit 119-103105-XX CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Downloaded from ProjectorsManual.com Manuals…
Page 102
Downloaded from ProjectorsManual.com Manuals…
Page 103
Downloaded from ProjectorsManual.com Manuals…
Page 104
Corporate ofﬁ ces Worldwide ofﬁ ces USA – Cypress United Kingdom Eastern Europe Singapore Japan ph: 714-236-8610 ph: +44 118 977 8000 ph: +36 (0) 1 47 48 100 ph: +65 6877-8737 ph: 81-3-3599-7481 Canada – Kitchener France Middle East Beijing South Korea ph: 519-744-8005…

Источник

More products and manuals for Projectors Christie

Models	Document Type
CP2230	Setup Guide Christie CP2230 Setup guide [en] , 72 pages
CP2000-X	User Manual Christie CP2000-X User manual, 164 pages
103-010100-01	User Manual Christie LX380 and LX450 Serial Communications, 26 pages
38-RS1002-01	Operator’s Manual Christie 38-RS1002-01 Operator`s manual [en] , 14 pages
CP2000-M	Setup Guide Christie CP2000-M Setup guide, 74 pages
CP2000-ZX	User Manual Christie CP2000-ZX User manual, 2 pages
LW551i	User Manual Christie LW551i User manual [en] , 128 pages
LX650	User Manual LX650 Lamp and Filter Replacement Instructions, 6 pages
38-VIV208-03	User Manual Christie 38-VIV208-03 User`s manual, 56 pages
LWU420	User Manual Christie LWU420 Technical User Manual, 29 pages
DWX951	User Manual Christie Q Series brochure, 8 pages
CP2000-ZX	Setup Guide Christie CP2000-ZX Setup guide, 58 pages
D4K25	User Manual Christie D4K25 and D4K35 Brochure, 6 pages
Mirage WQ-L	User Manual Christie Mirage WQ-L User manual, 80 pages
35/70	Operator’s Manual Christie 35/70 Operator`s manual, 56 pages
DWX951	User Manual Christie DWU951/DHD951/DWX951/DXG1051 Technical Operating [en] , 45 pages
CineIPM-2K	User Manual Christie CineIPM-2K User`s manual, 122 pages
103-011100-01	User Manual 2 — Christie, 4 pages
RPMX-D132U	User Manual Product Sheet — About Projectors, 4 pages
HD8K	User Manual HD Series, 8 pages

Источник

Компактный DLP-проектор линейки Christie Solaria® для киноэкранов шириной до 15 м

Christie® CP2215 – самый компактный цифровой кинопроектор в мире. Его чаще всего выбирают ведущие студии пост—продакшн и кинопоказчики, для которых решающую роль играет размер помещения киноаппаратной. Яркость проектора регулируется под нужды конкретного кинозала. Christie® CP2215 совместим с большинством IMB. Он входит в линейку проекторов Christie Solaria®, создан на основе DLP Cinema® технологии 2 серии Texas Instruments и соответствует требованиям Digital Cinema Initiatives (DCI).

Поддержка технологии HighFrameRate (HFR)

Вкладывая в технологию HFR, вы готовитесь к следующему этапу развития цифрового кино. Показывайте в первоклассных форматах 2D/3D HFR художественные фильмы и альтернативный контент в его оригинальном формате – это лучшее визуальное предложение для ваших зрителей.

Для простоты интеграции в любое помещение предлагается дополнительное оборудование Christie: ChristieIntegratedMediaBlock (IMB), A/VCinemaScalerProIIIдля альтернативного контнета, ChristieSKA-3Dдля экономичной обработки Audio/Video, система автоматизации и контроля ChristieACT и полный комплект объективов и ламп.

Christie CP2215 создан на основе 0.98″ DLP Cinema® технологии. В нем используются высокопроизводительные, с длительным сроком службы ксеноновые лампы серии CDXL, включая новые лампы CDXL-23S, обеспечивающие увеличение срока службы и низкое энергопотребление.

Надежный цифровой кинопроектор CP2215 оснащен моторизированным держателем для объектива. Для него имеется широкий спектр объективов, что позволит использовать его практически в любом зале.

Основные особенности:

Полная DCI-совместимость
3D ready
Базовая поддержка HDCP и SNMP
Низкая стоимость владения
Локальная система управления через сенсорную панель Touch Panel Controller (TPC) и полный доступ из любой точки через веб- GUI
Компактная архитектура обеспечивает гибкость сборки и установки
Сплит операция питания для использования с UPS
Доступ к задней панели для удобства замены лампы
Новая интеллектуальная система Lens System™ (ILS)
Christie CP2215 не требует теплоотведения (опция)

Технические характеристики	Christie CP2215
Лампы	1.4kW (CDXL-14M) 003-003066-01 1.6kW (CDXL-16M) 003-003900-01 1.8kW (CDXL-18SD) 003-002742-01 2.0kW (CDXL-20SD) 003-001976-01 2.3kW (CDXL-23S) 003-004769-01
Номинальная яркость	2900-15000 люмен
Размер экрана	до 15 м
Поддерживаемая скорость проекции	2D — до 120 fps, 3D — до 60 fps/на один глаз
Контрастность	2000:1 по методу полного поля вкл./выкл.
Digital micromirror device	0.98″ 2K 3-chip DMD DLP Cinema^®
Разрешение	2048 x 1080 пикселей
Количество цветов	35,2 трлн
Напряжение входной линии	220 В, однофазное питание
Блок питания лампы	Импульсный блок питания лампы с низким уровнем пульсаций; мощность 700 Вт – 2,3 кВт
Стандартные входы	2 x HD-SDI inputs for 2K source content 2 x DVI (HDMI) inputs for alternative content
Аксессуары	Christie IMB-S2 (108-384107-01) Адаптер с 90-градусной выходной трубкой (119-103105-01) Монтажная стойка (108-416102-01) Link Decryptor 003-120535-01
Размер	(Д х Ш х В): 687 x 665 x 395 мм
Вес	Система в сборе: 55 кг

8 (812) 449-70-70, доб. 201.

cinemas@nevafilm.ru

Источник

File Specifications:

653/653623-cp2215.pdf file (18 Sep 2023)

Accompanying Data:

Christie CP2215 Projector PDF Operation & User’s Manual (Updated: Monday 18th of September 2023 09:02:02 AM)

Rating: 4.5 (rated by 44 users)

Compatible devices: RoadRunner L8, Christie LX66A, LW720, 38-VIV303-01, Roadster, 3308-VIV303-01, Roadie HD+30K, CP2320-RGB.

Operation & User’s Manual (Text Version):

(Ocr-Read Summary of Contents of some pages of the Christie CP2215 Document (Main Content), UPD: 18 September 2023)

90, 82 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Maintenance Inspect the Card Cage Filter Use only high efficiency Christie approved filters. Never operate the projector without the filter installed. You should check the condition of the card cage air filter monthly. Clean or replace the …
79, Christie CP2215 CP2215 User Manual 71 020-101225-01 Rev. 1 (01-2014) Troubleshooting This section provides information and procedures for resolving common projector issues. If you cannot resolve a projector issue, contact Christie support . In order that a support representative can better assist you, have the model and serial number of your projector ready. For contact information see the back cover of this document. Projector Functionality Issue Resolution Pr…
29, CP2215 User Manual 21 020-101225-01 Rev. 1 (01-2014) Adjust the Image This section provides information and procedures for adjusting the projector image. Correct Keystone Effect Keystone effect occurs when you project an image onto the screen at an angle and the projector is not centered on the screen. The image will appear distorted and resemble a trapezoid. This image identifies horizontal (A) and vertical (B) keystone effect. Horizontal keys…
20, Installation and Setup CP2215 User Manual 12 020-101225-01 Rev. 1 (01-2014) Connect the Projector to a Computer Connect one end of an Ethernet or a RS232 cable to the Ethernet or the RS232 PIB port on the projector communications panel and the other end to your computer. To communicate with the projector, the projector must be added to the same network as the computer. See Add the Projector to a Network on pa…
54, 46 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Manage Projector Setting Files 2. Tap Save As. 3. Enter a name for the source file in the Filename field. 4. Tap OK. 5. Complete these fields: 6. Tap Save. Modify a Screen File 1. Tap Menu > Advanced Setup > Screen File Setup. 2. Select a screen …
12, Installation and Setup CP2215 User Manual 4 020-101225-01 Rev. 1 (01-2014) Projector Components — Rear Position the Projector 1. If you are installing the projector in the optional rack stand (P/N 108-416102-XX) follow the instructions provided with the rack stand to install it. 2. Position the projector so it is centered and parallel with the theatre screen. If space is limited, aim the projector slightly off-center and u…
87, Christie CP2215 Maintenance CP2215 User Manual 79 020-101225-01 Rev. 1 (01-2014) Remove the Existing Lamp 1. Tap and hold the red power button on the TPC Main panel to turn the lamp and projector off. 2. Allow the lamp to cool for a minimum of 15 minutes. 3. Unplug the projector. 4. Put on your protective clothing and face shield. 5. Insert the key in the lock on the lamp door, turn the key, and then open the…
100, 92 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Specifications Environment Operating Environment Non-Operating Environment Item Description Temperature 10°C to 35°C (50°F to 95°F) Humidity (non-condensing) 20% to 80% Altitude 0 — 3000 meters Maximum ambient temperature 3…
47, Work with Channels CP2215 User Manual 39 020-101225-01 Rev. 1 (01-2014) 7. Tap Activate to activate the channel. Activate a Channel 1. Tap Menu > Channel Setup. 2. Select a channel in the Channel Name list. 3. Tap Activate. Restore Default Channel Settings 1. Tap Menu > Channel Setup. 2. Select a channel in the Channel Name list. 3. Tap Defaults. 4. Tap Default Current Channel to restore the default settings to the selected chan…
32, 24 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Adjust the Image 4. Loosen the right boresight set screw (B). 5. Turn the right boresight cap screw (A) 1/16 of a turn clockwise. 6. Adjust the left boresight cap screw (C) equally in the opposite direction. 7…
39, Access the Projector and Run Diagnostics CP2215 User Manual 31 020-101225-01 Rev. 1 (01-2014) View the Status of Projector Components Tap Menu > Status. The Status window displays information about the status of projector components. The right pane lists projector components and their status. The left pane displays detailed information about individual projector items. A green LED indicates the i…
83, CP2215 User Manual 75 020-101225-01 Rev. 1 (01-2014) Maintenance This section provides information and procedures for performing projector maintenance. You should read through this section in its entirety before performing maintenance activities. When you perform projector maintenance, obey all warnings and precautions. Inspect Ventilation Vents and louvers in the projector covers provide ventilation, both for intake and e…
46, 38 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Work with Channels 6. Tap 3D Control in the left pane if the channel will be used to display 3D content. Complete these fields: Color Space The method of color decoding for the current source. The default is Y…
69, Backup, Restore, and Upgrade Projector Files CP2215 User Manual 61 020-101225-01 Rev. 1 (01-2014) Move Files to the Projector 1. To move files from a USB Flash drive, insert the USB flash drive into the USB port on the side of the touch panel controller (TPC). 2. Tap Menu > Service Setup > File Maintenance. 3. Select a file type in the File Type list. 4. Tap and drag a file from the TPC Files pane to the …
88, 80 CP2215 User Manual 020-101225-01 Rev. 1 (01-2014) Maintenance g. With the lamp removed, visually inspect the reflector and clean if necessary. 8. Remove the new lamp from the protective case. 9. Loosen the cathode screw and remove the cathode nut from the lamp. Ins…
35, Adjust the Image CP2215 User Manual 27 020-101225-01 Rev. 1 (01-2014) Typically, you install top and side masking to allow a greater range of adjustment. Calibrate Screen Brightness (fL) 1. Turn the lamp on and allow it to operate for 20 minutes. 2. On the touch pad controller, tap Menu > Administrator Setup > Foot Lamberts Calibration. 3. Complete the Foot Lamberts Calibration wizard. …

Christie CP2215 User Manual
Christie CP2215 User Guide
Christie CP2215 PDF Manual
Christie CP2215 Owner’s Manuals

Recommended: A105-S171, ecoTEC plus 612, SM-LCD710, LTA-260

Links & Tools

Operating Impressions, Questions and Answers:

Источник

Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Projector Components — Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connect the Exhaust Duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Install the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Turn the Projector On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Log On to the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Activate Marriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Turn the Lamp On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Adjust the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Correct Keystone Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Correct Vignetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjust Horizontal Boresight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CP2215 User Manual

020-101225-01 Rev. 1 (01-2014)

Downloaded from ProjectorsManual.com Manuals

AC/Power Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Lamp Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Encrypted Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Источник

Quick Links

Related Manuals for Christie cp2215

Summary of Contents for Christie cp2215

Page 3: Table Of Contents

Page 9: Installation And Setup

Page 10: Ac/Power Precautions

Page 11: Lamp Precautions

Page 12: Projector Components — Rear

Page 13: Adjust Tilt And Level The Projector

Page 14: Connect The Exhaust Duct

Page 15: Install The Lens

Page 16: Install The Lamp

Page 18: Connect Devices To The Projector

Page 20: Connect The Projector To A Computer

Page 21: Connect Devices To The Scci Port

Page 22: Connect Power

Page 23: Turn The Projector On

Page 24: Activate Marriage

Page 25: Add The Lamp Information To The Lamp History

Page 26: Adjust The Image To Fit Your Screen

Page 27: Play Content

Page 29: Adjust The Image

Page 30: Adjust Vertical Boresight Angle

Page 31: Adjust Horizontal Boresight

Page 33: Adjust Dmd Convergence

Page 34: Color Calibration

Page 35: Calibrate Screen Brightness (Fl)

Page 37: Access The Projector And Run Diagnostics

Page 38: Log On To The Projector

Page 39: View The Status Of Projector Components

Page 40: Respond To Alarms

Page 41: View Smpte Errors

Page 42: Turn The Projector Off

Page 43: Manage The Dlp

Page 44: Disable The Icp Signature Test

Page 45: Work With Channels

Page 47: Activate A Channel

Page 48: Change The Channel Icon

Page 49: Manage Lamp Information

Page 50: Enable Or Disable Liteloc On A Lamp File

Page 51: Add A Lamp To The Lamp History

Page 53: Manage Projector Setting Files

Page 54: Modify A Screen File

Page 55: Modify A Mcgd File

Page 56: Create A New Ils File

Page 57: Reset Ils File Settings

Page 58: Reset The Ils And The Lens Position

Page 59: Work With The Scheduler

Page 60: Delete A Scheduled Event

Page 61: View And Modify Projector Settings

Page 62: Modify Projector Communication Settings

Page 63: Access A Network Device

Page 64: View Microsoft Windows Explorer

Page 65: Manage User Accounts

Page 66: Delete A User Account

Page 67: Backup, Restore, And Upgrade Projector Files

Page 68: Back Up Projector Settings And Information

Page 69: Move Files To The Projector

Page 71: Test Patterns

Page 73: View 3D Content

Page 74: Hardware Setup

Page 76: Edit The Default 3D Lamp File

Page 77: Edit The 3D Scope 2048 X 858 Channel

Page 78: Display 3D Diagnostic Test Patterns

Page 79: Troubleshooting

Page 80: Lamp Functionality

Page 83: Maintenance

Page 84: Clean The Radiator Filter

Page 85: Inspect The Lamp

Page 86: Clean The Lens

Page 87: Remove The Existing Lamp

Page 88: Install The New Lamp

Page 90: Inspect The Card Cage Filter

Page 91: Replace The Lens

Page 93: Specifications

Page 94: White Point

Page 95: Rs232-Icp

Page 96: 3D Terminal

Page 97: Touch Panel Controller

Page 98: Lamp