Pool basic pro evo инструкция pdf

Seko Pool Basic Pro Evo User Manual

  1. Manuals
  2. Brands
  3. Seko Manuals
  4. Controller
  5. Pool Basic Pro Evo
  6. User manual

  • Contents

  • Table of Contents

  • Bookmarks

Quick Links

User Manual

1

0000137188

Rev. 1.0

loading

Related Manuals for Seko Pool Basic Pro Evo

  • Controller Seko Kontrol 800 Installation Manual

Summary of Contents for Seko Pool Basic Pro Evo

  • Page 1
    User Manual 0000137188 Rev. 1.0…

  • Page 2: Table Of Contents

    CONTENTS 1. GENERAL INTRODUCTION ……………………..3 2. INSTALLATION PRECAUTIONS ……………………3 3. IDENTIFICATION OF COMPONENTS ……………………4 4. TECHNICAL SPECIFICATIONS ……………………..5 5. ASSEMBLY INSTRUCTIONS ……………………..6 5.1 APPLICATION EXAMPLE ……………………..7 6. DESCRIPTION OF THE CIRCUIT ……………………8 7. CALIBRATION MENU ……………………….8 7.1 C …………………………..8 ALIBRATION 8.

  • Page 3: General Introduction

    1. GENERAL INTRODUCTION The Pool Basic Pro EVO control method belongs to a new line of instruments carefully developed by the supplier for the innovative management of pools. This device is easy to use and permits continuous control of the pH.

  • Page 4: Identification Of Components

    3. IDENTIFICATION OF COMPONENTS Instructions manual PH 7 PH 4 A. Pool Basic Pro EVO regulator B. Suction hose in PVC Crystal 4×6 (4 m) x 2 C. Delivery hose in PE 4X6 (5 m) x 2 D. pH Electrode model SPH-1 E.

  • Page 5: Technical Specifications

     Input signal: 100÷240 Vac  Level probe: pH, H Install the Pool Basic Pro EVO control device on a hard support (vertical wall) where it can be easily accessed by the operator. Attach the Pool Basic Pro EVO control device using the provided fixing bracket (distance between centre of holes: 95mm.

  • Page 6: Assembly Instructions

    5. ASSEMBLY INSTRUCTIONS Max. length of cable: 6m Lunghezza massima de cavo: 6 mt * NOTA 1 *NOTE 1 Maximum pressure Pressione Massima: 1,5 bar *NOTE 1 * NOTA 2 *NOTE 1: FOR LARGE PUMPS, THE CABLE MUST PASS THROUGH AN AREA OTHER THAN THE POWER * NOTA 1: IL CAVO DEVE PASSARE IN UNA ZONA DIVERSA DA QUELLA DI ALIMENTAZIONE SUPPLY ZONE IN ORDER TO PREVENT CURRENT DISTURBANCES.

  • Page 7: Application Example

    5.1 APPLICATION EXAMPLE COMPENSATION FILTER HEAT TANK INTERCHANGER RECIRCULATION PUMP Note: The linear distance of the hose between the probe and the point of injection must not be less than 60cm. 0000137188 Rev. 1.0…

  • Page 8: Description Of The Circuit

    6. DESCRIPTION OF THE CIRCUIT 1) Inlet pH measurement 2) Inlet temperature probe 3) Inlet probe level for product pH 4) Inlet probe level for product H 5) Keyboard input 6) Flow (recirculation pump) 7) Relay for pH product, external pump. 8) Alarm relay 9) Relay for H product, external pump.

  • Page 9
    7.1.1 Calibrating the pH probe Wash the probe Remove the probe from the probe Get some water holder Press CAL 25°C 14pH B.Solution Press and hold down the Cal button Press Cal to start calibration with a for 3 seconds Keep the probe in the buffer solution buffer solution pH 7 pH 7…

  • Page 10: Programming

    8. PROGRAMMING The programming menu can be accessed by simultaneously pressing the Cal and Set keys for at least 3 seconds. Upon release of the keys the display will show: Language Display Settings Press Enter and the + and – keys to change Progrma Menu the language: Language…

  • Page 11
    measurement display Settings Use Enter to access the sub-menus:  Hose Progrma Menu  Conc.  Pump Use Enter to modify the dimensions of the hose (3×7 or 6x10mm) and the system automatically calculates the flow Tube 6×10 rate with the other hose without changing any parameters (the factory-set hose is 6×10).
  • Page 12
    Press Esc to exit any menu and confirm the settings by pressing Enter. Display Settings Press the + and – keys to choose Save or Progrma Menu NoSave, i.e. to save the settings or not and Exit Save press Enter to confirm. DISPLAY VIEW WITH THE SYSTEM ON STAND-BY Stand-by display Operation…

  • Page 13: Dosing Method

    9. DOSING METHOD The control of the pumps in the pH scale is carried out through the PWM function. The proportional band is set to values pH= 0.8 pH proportional dosing The instrument allows the chemical measurement to be controlled and modified through the pH Set Point automatically;…

  • Page 14: On/Off P Hdosing

    ON/OFF pH dosing The instrument allows the chemical measurement to be controlled and modified through the pH Set Point automatically; adjusting the dosing though the pH motor controlled in ON/OFF. The dosing below is obtained by setting the following parameters: …

  • Page 15: Activations

    10. ACTIVATIONS  Flow Function Through the recirculation pump. High voltage input 100 ÷ 240 Vac, the dosing system is switched on. High voltage input is off (the recirculation pump is switched off), the dosing system shows FLOW flashing. 11. ALARMS Lev pH= pH product level probe alarm.

  • Page 16: List Of Possible Anomalies And Relative Solutions

    13. LIST OF POSSIBLE ANOMALIES AND RELATIVE SOLUTIONS ANOMALY CAUSE SOLUTION 1) Check for possible short circuits on the electrode  instrument connection cable (between the cable’s core and the external instrument Problem with the cable and/or shielding). always indicates pH connector.

  • Page 17: Handling

    14. HANDLING Hose replacement: Position the roller at 20 past 10, Completely release left Release the cover by pulling the turning it in the direction of the connector, holding it taut towards the left connector upward. circular arrow. outside, and turn the roller in the direction of the circular arrow so that the hose is freed up to the right connector.

  • Page 18: Storing The Pump After Use

    15. STORING THE PUMP AFTER USE When the regulation device must be stored, clean water should be pumped through the hose in order to rinse it. Then position the probe holder at 7h05, turning in the direction indicated by the circular arrow.

  • Page 19: Warnings

    WARNINGS PRODUCTS TO BE USED:  pH Reduction: product with a sulphuric acid base, easily found on the market.  pH Increase: product with an alkaline acid base PRODUCTS NOT RECOMMENDED  Do not use hydrochloric acid. Ask the installer about all other products. PROBE WARNINGS …

This manual is also suitable for:

Pool basic pro evo

Источник

(Ocr-Read Summary of Contents of some pages of the Seko Pool Basic Pro Evo Document (Main Content), UPD: 06 September 2023)

  • 1, Seko Pool Basic Pro Evo 0000137188 Rev. 1.0 1 User Manual
    …

  • 2, 0000137188 Rev. 1.0 2 CONTENTS 1. GENERAL INTRODUCTION ……………………………………………………………………………………………………………….3 2. INSTALLATION PRECAUTIONS …………………………………………………………………………………………………………3 3. IDENTIFICATION OF COMPONENTS ……………………………………..…

  • 3, 0000137188 Rev. 1.0 3 1. GENERAL INTRODUCTION The Pool Basic Pro EVO control method belongs to a new line of instruments carefully developed by the supplier for the innovative management of pools. This device is easy to use and permits continuous control of the pH. The peristaltic pumps have a 1,5 l/h flow rate for pH regulation and have a pressurised injection flow rate up to 1.5 bar. This easy-to-u…

  • 4, 0000137188 Rev. 1.0 4 3. IDENTIFICATION OF COMPONENTS PH 7 PH 4 H0 2 B C D F G M E Instructions manual K L N H I J O KEY A. Pool Basic Pro EVO regulator B. Suction hose in PVC Crystal 4×6 (4 m) x 2 C. Delivery hose in PE 4X6 (5 m) x 2 D. pH Electrode model SPH-1 E. Reducer for injection valve x 2 F. Duckbill valve in F…

  • 5, 0000137188 Rev. 1.0 5 O. Temperature sensor 4. TECHNICAL SPECIFICATIONS Power supply: 100÷240 Vac 50/60 Hz 30 watt Switch: on side of box Inlet measurements: pH, through BNC o pH scale: 0÷14.0 pH o pH precision: +/-0.1 pH Temperature Scale: 0÷100 °C (PT100 sensor) Pump flow rate with transaxle technology: o pH: 1.5 l/h (hose 6X10) 1.…

  • 6, 0000137188 Rev. 1.0 6 5. ASSEMBLY INSTRUCTIONS NO NO * NOTA 2: LA PRESSIONE MAX. NON DEVE ESSERE SUPERIORE A 1,5 BAR. PER AUMENTARE LA DURATA DEL TUBO, LA PRESSIONE NON DEVE SUPERARE 1 BAR. * NOTA 1: IL CAVO DEVE PASSARE IN UNA ZONA DIVERSA DA QUELLA DI ALIMENTAZIONE PER POMPE GROSSE, PER EVITARE DIS…

  • 7, 0000137188 Rev. 1.0 7 5.1 APPLICATION EXAMPLE PH Note: The linear distance of the hose between the probe and the point of injection must not be less than 60cm. COMPENSATION TANK RECIRCULATION PUMP FILTER HEAT INTERCHANGER
    …

  • 8, Seko Pool Basic Pro Evo 0000137188 Rev. 1.0 8 6. DESCRIPTION OF THE CIRCUIT 1) Inlet pH measurement 2) Inlet temperature probe 3) Inlet probe level for product pH 4) Inlet probe level for product H 2 O 2 5) Keyboard input 6) Flow (recirculation pump) 7) Relay for pH product, external pump. 8) Alarm relay 9) Relay for H 2 O 2 product, external pump. 10) Power supply inp…

  • 9, 0000137188 Rev. 1.0 9 7.1.1 Calibrating the pH probe Get some water Remove the probe from the probe holder Wash the probe Keep the probe in the buffer solution pH 7 Press and hold down the Cal button for 3 seconds Tm 25°C 14pH Press Cal to start calibration with a buffer solution pH 7 Press CAL B.Solution 7pH The calibration takes 1 minu…

  • 10, 0000137188 Rev. 1.0 10 8. PROGRAMMING The programming menu can be accessed by simultaneously pressing the Cal and Set keys for at least 3 seconds. Upon release of the keys the display will show: To prime the pH pump, press the UP button for at least 3 seconds and release it to stop the operation. To prime the H 2 O 2 pump repeat the same procedure pressing the DOWN button for at least 3 seconds. …

  • 11, 0000137188 Rev. 1.0 11 H 2 O 2 measurement display Settings Progrma Menu H 2 O 2 Use Enter to access the sub-menus: Hose Conc. Pump H 2 O 2 Tube 6×10 Use Enter to modify the dimensions of the hose (3×7 or 6x10mm) and the system automatically calculates the flow rate with the other hose without changing any parameters (the factory-set h…

  • 12, 0000137188 Rev. 1.0 12 Press Esc to exit any menu and confirm the settings by pressing Enter. DISPLAY VIEW WITH THE SYSTEM ON STAND-BY *If AdvancedFlow=On and during H 2 O 2 dosing, the recirculation pump stops and blocks the system dosing, when the pump restarts, the H 2 O 2 will restart the cc dosing calculated from the start. SHORTCUTS To access the shortcut menu press the SET key fo…

  • 13, Seko Pool Basic Pro Evo 0000137188 Rev. 1.0 13 9. DOSING METHOD The control of the pumps in the pH scale is carried out through the PWM function. The proportional band is set to values pH= 0.8 9.1 pH proportional dosing The instrument allows the chemical measurement to be controlled and modified through the pH Set Point automatically; adjusting the dosing though the pH mot…

  • 14, 0000137188 Rev. 1.0 14 9.2 ON/OFF pH dosing The instrument allows the chemical measurement to be controlled and modified through the pH Set Point automatically; adjusting the dosing though the pH motor controlled in ON/OFF. The dosing below is obtained by setting the following parameters:  Set point pH = 7.20 pH  Type of Dosing = Alkaline Set Point pH Motore pH 9.3 Alarm for the pH Set Point W…

  • 15, 0000137188 Rev. 1.0 15 10. ACTIVATIONS Flow Function Through the recirculation pump. High voltage input 100 ÷ 240 Vac, the dosing system is switched on. High voltage input is off (the recirculation pump is switched off), the dosing system shows FLOW flashing. 11. ALARMS Lev pH= pH product level probe alarm. Lev H 2 O 2 = Flocculant product level probe alarm…

  • 16, 0000137188 Rev. 1.0 16 13. LIST OF POSSIBLE ANOMALIES AND RELATIVE SOLUTIONS ANOMALY CAUSE SOLUTION The instrument always indicates pH 7.00 Problem with the cable and/or connector. 1) Check for possible short circuits on the electrode  instrument connection cable (between the cable’s core and the external shielding). 2) Make sure that there are no traces …

  • 17, 0000137188 Rev. 1.0 17 14. HANDLING Hose replacement: Release the cover by pulling the left connector upward. Position the roller at 20 past 10, turning it in the direction of the circular arrow. Completely release the left connector, holding it taut towards the outside, and turn the roller in the direction of the circular arrow s…

  • 18, Seko Pool Basic Pro Evo 0000137188 Rev. 1.0 18 15. STORING THE PUMP AFTER USE When the regulation device must be stored, clean water should be pumped through the hose in order to rinse it. Then position the probe holder at 7h05, turning in the direction indicated by the circular arrow. These two precautions will facilitate the subsequent reactivation of the unit. …

  • 19, 0000137188 Rev. 1.0 19 WARNINGS PRODUCTS TO BE USED: pH Reduction: product with a sulphuric acid base, easily found on the market. pH Increase: product with an alkaline acid base PRODUCTS NOT RECOMMENDED Do not use hydrochloric acid. Ask the installer about all other products. PROBE WARNINGS Handle the probe with CARE. DO NOT INSERT AN…

Источник

Table of Contents for Seko Pool Basic Pro Evo:

  • 0000137188 Rev. 1.0 18 15. STORING THE PUMP AFTER USE When the regulation device must be stored, clean water should be pumped through the hose in order to rinse it. Then position the probe holder at 7h05, turning in the direction indicated by the circular arrow. These two precautions will fac

  • 0000137188 Rev. 1.0 19 WARNINGS PRODUCTS TO BE USED:  pH Reduction: product with a sulphuric acid base, easily found on the market.  pH Increase: product with an alkaline acid base PRODUCTS NOT RECOMMENDED  Do not use hydrochloric acid. Ask the installer about all other products. PROBE WARNINGS  Handle the pr

  • 0000137188 Rev. 1.0 16 13. LIST OF POSSIBLE ANOMALIES AND RELATIVE SOLUTIONS ANOMALY CAUSE SOLUTION The instrument always indicates pH 7.00 Problem with the cable and/or connector. 1) Check for possible short circuits on the electrode  instrument connection cable (between the cable’s core and the external shielding). 2) Make sure that there are no traces of humidity and/or condensation on the connector of the prob

  • 0000137188 Rev. 1.0 11 H 2 O 2 measurement display Settings Progrma Menu H 2 O 2 Use Enter to access the sub-menus:  Hose  Conc.  Pump H 2 O 2 Tube 6×10 Use Enter to modify the dimensions of the hose (3×7 or 6x10mm) and the system automatically calculates the flow rate with the other hose without changing any parameters (the factory-set hose is 6×10). H

  • 0000137188 Rev. 1.0 1 User Manual

  • 0000137188 Rev. 1.0 5 O. Temperature sensor 4. TECHNICAL SPECIFICATIONS  Power supply: 100÷240 Vac 50/60 Hz 30 watt  Switch: on side of box  Inlet measurements: pH, through BNC o pH scale: 0÷14.0 pH o pH precision: +/-0.1 pH  Temperature Scale: 0÷100 °C (PT100 sensor)  Pump flow rate with transaxle technology: o pH: 1.5 l/h (hose 6X10) 1.5 bar o H 2 O 2 : 0.4 l/h (hose 3X7), 1.5 l/h (hose 6X10) 1.5 bar  Pump relay pH: 10 A 250 V (dry contact)  Rela

  • 0000137188 Rev. 1.0 2 CONTENTS 1. GENERAL INTRODUCTION ……………………………………………………………………………………………………………….3 2. INSTALLATION PRECAUTIONS …………………………………………………………………………………………………………3 3. IDENTIFICATION OF COMPONENTS ………………

  • 0000137188 Rev. 1.0 14 9.2 ON/OFF pH dosing The instrument allows the chemical measurement to be controlled and modified through the pH Set Point automatically; adjusting the dosing though the pH motor controlled in ON/OFF. The dosing below is obtained by setting the following parameters:  Set point pH = 7.20 pH  Type of Dosing =

  • 0000137188 Rev. 1.0 17 14. HANDLING Hose replacement: Release the cover by pulling the left connector upward. Position the roller at 20 past 10, turning it in the direction of the circular arrow. Completely release the left connector, holding it taut towards the outside, and turn the roller in the direction of the circular arrow so that the hose is freed up to the right connector. Position the rol

  • 0000137188 Rev. 1.0 9 7.1.1 Calibrating the pH probe Get some water Remove the probe from the probe holder Wash the probe Keep the probe in the buffer solution pH 7 Press and hold down the Cal button for 3 seconds Tm 25°C 14pH Press Cal to start calibration with a buffer solution pH 7 Press CAL B.Solution 7pH

  • 0000137188 Rev. 1.0 15 10. ACTIVATIONS  Flow Function Through the recirculation pump. High voltage input 100 ÷ 240 Vac, the dosing system is switched on. High voltage input is off (the recirculation pump is switched off), the dosing system shows FLOW flashing. 11. ALARMS Lev pH= pH product level probe alarm. Lev H 2 O 2 = Flocculant product l

  • 0000137188 Rev. 1.0 12 Press Esc to exit any menu and confirm the settings by pressing Enter. DISPLAY VIEW WITH THE SYSTEM ON STAND-BY *If AdvancedFlow=On and during H 2 O 2 dosing, the recirculation pump stops and blocks the system dosing, when the pump restarts, the H 2 O 2 will restart the cc dosing calculated from the start. SHORTCUTS To access th

  • 0000137188 Rev. 1.0 4 3. IDENTIFICATION OF COMPONENTS PH 7 PH 4 H0 2 B C D F G M E Instructions manual K L N H I J O KEY A. Pool Basic Pro EVO regulator B. Suction hose in PVC Crystal 4×6 (4 m) x 2 C. Delivery hose in PE 4X6 (5 m) x 2 D. pH Electrode model SPH-1 E. Reducer for injection valve x 2 F. Duckbill valve in FPM (3/8” GAS)

  • 0000137188 Rev. 1.0 7 5.1 APPLICATION EXAMPLE PH Note: The linear distance of the hose between the probe and the point of injection must not be less than 60cm. COMPENSATION TANK RECIRCULATION PUMP FILTER HEAT INTERCHANGER

Questions, Opinions and Exploitation Impressions:

You can ask a question, express your opinion or share our experience of Seko Pool Basic Pro Evo device using right now.

Источник

Seko Pumps

SEKO Pumps Предлагает надёжные решения при дозировании агрессивных и ядовитых жидкостей, дозирующее насосное оборудование высокого давления и производительности, мембранные насосы, насосы дозаторы, станции дозирования, блоки приготовления реагентов.
Дезинфецирующее оборудование, аппараты для дезинфекции в складских помещениях, офисах, транспортных средств, в фургонах рефрижераторах, в холодильных установках, поверхностей и гигиены рук для эффективного контроля и профилактики вирусов.

Доставка оборудования по России

Оборудование доставляется по указанному заказчиком адресу собственным транспортом или отправляется транспортной компанией по адресу нахождения терминалов в следующих городах:

Астрахань, Адлер, Архангельск, Абакан, Барнаул, Белгород, Благовещенск, Братск, Брянск, Великие Луки, Великий Новгород, Владивосток, Владимир, Волгоград, Волгодонск, Волжский, Вологда, Воронеж, Дзержинск, Димитровград, Екатеринбург, Забайкальск, Иваново, Ижевск, Иркутск, Йошкар-Ола, Казань, Калининград, Калуга, Кемерово, Киров, Коломна, Кострома, Котлас, Краснодар, Красноярск, Курган, Курск, Липецк, Москва, Магнитогорск, Мурманск, Набережные Челны, Нижневартовск, Нижний Новгород, Нижний Тагил, Новороссийск, Новосибирск, Новокузнецк, Новомосковск, Ногинск, Омск, Орел, Оренбург, Орск, Пенза, Пермь, Петрозаводск, Подольск, Псков, Пушкино, Фрязино, Ростов-на-Дону, Рыбинск, Рязань, Самара, Санкт-Петербург, Саранск, Саратов, Северодвинск, Серпухов, Смоленск, Солнечногорск, Сочи, Ставрополь, Старый Оскол, Стерлитамак, Сургут, Сызрань, Сыктывкар, Тамбов, Тверь, Тольятти, Томилино, Томск, Тула, Тюмень, Улан-Удэ, Ульяновск, Уфа, Ухта, Хабаровск, Чебоксары, Челябинск, Череповец, Чита, Энгельс, Ярославль.

Стоимость, срок поставки уточняйте у менеджеров.

Способы оплаты:
Безналичный расчет. Реквизиты для оплаты будут предоставлены после оформления заказа.

Источник
Document’s Content and Additional Information Share Manual

Seko Pool Basic Pro Evo Operation & user’s manual

  • Seko
  • Controller
  • Operation & user’s manual for Seko Pool Basic Pro Evo
  • seko-pool-basic-pro-evo-operation-user-s-manual-19_manual.pdf
  • 19 |

Pages Preview:



Document Transcription:

  • 0000137188 Rev. 1.0 9 7.1.1 Calibrating the pH probe Get some water Remove the probe from the probe holder Wash the probe Keep the probe in the buffer solution pH 7 Pre …

  • 0000137188 Rev. 1.0 10 8. PROGRAMMING The programming menu can be accessed by simultaneously pressing the Cal and Set keys for at least 3 seconds. Upon release of the keys the display will …

  • 0000137188 Rev. 1.0 15 10. ACTIVATIONS  Flow Function Through the recirculation pump. High voltage input 100 ÷ 240 Vac, the dosing system is switched on. High voltage input is off (t …

See Details
Download

Источник

Понравилась статья? Поделить с друзьями:
  • Сигнализация aps 7100 инструкция по установке
  • Эфалекс инструкция по применению для детей отзывы
  • Дифлюкан инструкция по применению для мужчин мазь
  • Кромицил глазные капли инструкция по применению цена отзывы аналоги
  • Как собрать двухъярусную кровать с диваном инструкция пошагово