Soundcore Liberty Air 2 Pro Руководство пользователя
ПОДДЕРЖКИ
Чтобы получить ответы на часто задаваемые вопросы, подробное руководство пользователя и дополнительную информацию, посетите www.soundcore.com/support
APP
Загрузите приложение Soundcore, чтобы настроить пользовательский интерфейс (например, отрегулировать громкость, управлять воспроизведением, активировать Siri), отследить HearID, настроить эквалайзер, переключить режимы ANC, обновить прошивку и узнать больше.
ОБНОВЛЕНИЕ ПРОШИВКИ
Убедитесь, что наушники помещены в зарядный футляр, а футляр остается открытым до завершения обновления прошивки.
ОКРУЖАЮЩИЙ ЗВУК
Переключите режимы ANC / Transparency / Normal в приложении Soundcore.
- ANC (активное шумоподавление): уменьшает нежелательный фоновый шум.
- Прозрачность: следите за окружением во время прослушивания музыки.
НОСИТЬ
Выберите ушные вкладыши из жидкого силикона, которые лучше всего подходят вашим ушам.
ЗАРЯДКА
Внимание!
- Перед зарядкой полностью вытрите наушники и порт зарядки USB-C.
- Во избежание повреждений используйте сертифицированный зарядный кабель USB-C.
- Для беспроводной зарядки поместите зарядный футляр в центр беспроводного зарядного устройства.
ВКЛЮЧЕНИЕ / ВЫКЛЮЧЕНИЕ ПИТАНИЯ
Откройте чехол для зарядки, наушники автоматически включатся. Чтобы выключить питание, поместите наушники в зарядный футляр и закройте его.
СОПРЯЖЕНИЕ
Откройте чехол для зарядки, наушники автоматически перейдут в режим сопряжения Bluetooth. Для подключения выберите «Soundcore Liberty Air 2 Pro» в списке Bluetooth вашего устройства.
КОНТРОЛЬ
x2: Нажмите дважды
2s: Нажмите и удерживайте в течение секунд 2
Автоматически приостанавливайте воспроизведение музыки при снятии наушников, наденьте их снова, чтобы возобновить.
ПОВТОРНОЕ СОПРЯЖЕНИЕ
Сопряжение с другим устройством: поместите наушники в зарядный футляр и оставьте футляр открытым. Нажмите и удерживайте кнопку на корпусе в течение 3 секунд, пока светодиодные индикаторы наушников не начнут мигать белым, чтобы перейти в режим сопряжения.
СБРОС
- Сбросьте настройки, если наушники не могут правильно соединиться друг с другом или с другими устройствами.
- Поместите наушники в зарядный футляр и оставьте футляр открытым.
- Нажмите и удерживайте кнопку на футляре в течение 10 секунд, пока светодиодные индикаторы наушников не мигнут 3 раза красным, а затем станут белыми.
- Подождите, пока светодиодный индикатор на одном из наушников не начнет быстро мигать, а на другом — медленно. Это подтверждает, что сброс прошел успешно, и ваши наушники могут быть подключены нормально.
СВЕТОДИОДНЫЙ НАПРАВЛЯЮЩИЙ
Служба поддержки игроков
service@soundcore.com
support.mea@soundcore.com (Только для Ближнего Востока и Африки)
support@anker.com
+971 8000320817 (ОАЭ) вс-чт 9:00 — 17:30 (GMT + 4)
+971 42463266 (Ближний Восток и Африка) вс-чт 9:00 — 17:30 (GMT + 4)
+966 8008500030 (KSA) вс-чт 8:00 — 16:30 (GMT + 3)
+965 22069086 (Кувейт) вс-чт 8:00 — 16:30 (GMT + 3)
+20 8000000826 (Египет) вс-чт 7:00 — 15:30 (GMT + 2)
Анкер Инновации Лимитед
Комната 1318-19, Голливуд Плаза, 610 Натан Роуд, Монгкок, Коулун, Гонконг
АНКЕР ТЕХНОЛОДЖИ (Великобритания) ЛТД
Suite B, Fairgate House, 205 Kings Road, Tyseley, Бирмингем, B11 2AA, Великобритания
Анкер Инновации Дойчланд ГмбХ
Georg-Muche-Strasse 3-5, 80807 Мюнхен, Германия
Документы / Ресурсы
Рекомендации
Charging
- Remove the protective film from the earbuds before the first use.
- Fully dry off the earbuds and the USB port before charging.
- Use a certified USB-C charging cable and charger to prevent any damage.
- Fully charge both the earbuds and the charging case before the first use.
- Place the earbuds in the charging case and close it.
The first and the third LED indicators on the charging case will flash twice. This confirms that the earbuds are being charged. - Connect the charging case to the power supply by using a USB-C charging cable. Alternatively, position the charging case at the center of your wireless charger for wireless charging. The LED indicators on the c harging case indicate the charging status.
- To check the battery level of the charging case, open it to activate the LED indicator.
The first and the third LED indicators on the charging case will flash twice. This confirms that the earbuds are being charged.
Download the Soundcore app to enhance your experience.
HearID: HearID maps your personal hearing sensitivity at multiple frequencies and analyzes the results. It traces the EQ settings and creates a personalized sound profile for you.
User interface customization: In stereo mode, all of the controls (e.g. adjust volume, control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app to optimize your experience while enjoying different music genres.
Noise cancellation: Choose an active noise cancellation mode to reduce ambient noise according to your surroundings.
- Transport: Targets low-end frequencies like engine and road noise for peaceful journeys and commutes.
- Outdoor: Reduces ambient sounds in cities for less distractions.
- Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside spaces.
Custom ANC: Adjust the noise cancellation level to suit you in the app.
Transparency mode: Stay aware of your surroundings by allowing ambient sounds in.
- Fully Transparent: Hear all ambient sounds.
- Vocal Mode: Voices stand out more clearly from other ambient sounds.
Earbuds firmware update: You will be informed once the new version of firmware is detected when you connect the earbuds with the app. Ensure the earbuds are placed in the charging case and the case remains open until the firmware upgrade is completed. During the upgrade, ensure the earbuds are being charged and avoid any operation.
Wearing
- Choose the EarTips that fit your ears best.
- Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.
Your earbuds come with multiple pairs of EarTips, among which Medium-sized are pre-installed.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
The LED indicator on earbuds will light up white for 1 second.
To power off, place the earbuds in the charging case and it.
When you’re wearing the earbuds, they will not power off until out of battery. When you remove the earbuds, they will automatically power off after 30 minutes if no device is connected.
Bluetooth Pairing
- Open the charging case, the earbuds will automatically enter the Bluetooth pairing mode. The LED indicator on one earbud will flash quickly and on another earbud breathe slowly.
- Select «Soundcore Liberty Air 2 Pro» on your device’s Bluetooth list to connect. When successfully connected, the LED indicator on earbuds will light up white for 1 second.
The LED indicator on one earbud will flash quickly and on another earbud breathe slowly.
- Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range.
- Mono mode: When Bluetooth connected, you can use either one of the earbuds only by placing the other one into the charging case and closing it.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
- When you are on a call, place either one of the earbuds into the charging case and close it, the microphone in the other earbud will be activated.
Pairing with another device
- Place the earbuds in the charging case and leave the case open. Press and hold the button on the case for 3 seconds until the earbud LED indicators flash white to enter the pairing mode.
- Select «Soundcore Liberty Air 2 Pro» on your device’s Bluetooth list to connect.
Controls
 |
|
| Play/Pause | Tap twice (R) |
| Next track | Tap twice (L) |
 |
|
| Answer a call | Tap twice (L/R) |
| Answer a second incoming call and put the current call on hold | |
| End/Reject a call | Press and hold for 2 seconds (L/R) |
| Switch between a call on hold and an active call | |
 |
|
| Switch ambient sound modes (Noise Cancellation/Normal) | Press and hold for 2 seconds (L/R) |
| Mono mode | |
| Play/Pause | Tap twice |
| Answer a call | |
| End/Reject a call | Press and hold for 2 seconds |
| Activate Siri or other voice assistant software |
- All of the controls in stereo mode can be customized in the Soundcore app. In mono mode, controls cannot be customized in the app.
- Music playback will auto-pause when removing the earbuds, wear them again to resume.
- Adjust the volume level via the connected device or in the Soundcore app.
- In stereo mode, noise cancellation mode is set by default. Each time you power on and connect, or switch to the stereo mode from mono mode, your earbuds will restore the last setting.
- Noise cancellation or transparency mode is unavailable in mono mode.
Reset
You might need to reset your earbuds if you experience any connectivity problems or function issues.
- Place the earbuds in the charging case and leave the case open.
- Press and hold the button on the case for 10 seconds until the earbud LED indicators flash red 3 times and then turn white.
- Wait until the LED indicator on one of the earbuds flashes fast while the other breathes slowly. This confirms that the reset was successful and your earbuds can be connected normally.
The following two examples indicate the reset has not been successful and the previous steps should be repeated.
- If only one earbud LED indicator flashes;
- If both earbud LED indicators flash quickly.
Specifications
Specifications are subject to change without notice.
| Input | 5 V  0.5 A |
| Rated output power | 5 mW @ 1% THD |
| Battery capacity | 55 mA x 2 (earbuds); 500 mA (charging case) |
| Charging time | 2 hours 15-minute charge = 3-hour playtime |
| Playtime (varies by volume level and content) | Up to 7 hours (Total 26 hours with the charging case) |
| Playtime (with ANC mode turned on) | Up to 6 hours (Total 21 hours with the charging case) |
| Playtime (with transparency mode turned on) | Up to 6.5 hours (Total 23 hours with the charging case) |
| Talk time | Up to 4 hours (Total 14 hours with the charging case) |
| Driver size | 11 mm |
| Frequency response | 20 Hz — 20 kHz |
| Impedance | 16 Ω |
| Waterproof level (The waterproof level may reduce over time as a result of daily use) | IPX4 (The earbuds are not desig ned for swimming, showering, or exposure to pool or ocean water. Do not use in a sauna or steam room. The charging case is not waterproof. ) |
| Bluetooth version | V 5.0 |
| Bluetooth range | 10 m / 33 ft |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Liberty Air 2 Pro
USER MANUAL
Charging
Download the Soundcore app to enhance your experience. HearID: HearID maps your personal hearing sensitivity at multiple frequencies and analyzes the results. It traces the EQ settings and creates a personalized sound profile for you.
User interface customization: In stereo mode, all of the controls (e.g. adjust volume, control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app to optimize your experience while enjoying different music genres.
Noise cancellation: Choose an active noise cancellation mode to reduce ambient noise according to your surroundings.
- Transport: Targets low-end frequencies like engine and road noise for peaceful journeys and commutes.
- Outdoor: Reduces ambient sounds in cities for less distractions.
- Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside spaces.
Custom ANC: Adjust the noise cancellation level to suit you in the app.
Transparency mode: Stay aware of your surroundings by allowing ambient sounds in. - Fully Transparent: Hear all ambient sounds.
- Vocal Mode: Voices stand out more clearly from other ambient sounds.
Earbuds firmware update: You will be informed once the new version of firmware is detected when you connect the earbuds with the app. Ensure the earbuds are placed in the charging case and the case remains open until the firmware upgrade is completed. During the upgrade, ensure the earbuds are being charged and avoid any operation.
Wearing
- Choose the Liquid Silicone EarTips that fit your ears best.
- Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.
Your earbuds come with multiple pairs of EarTips, among which Medium-sized are pre-installed.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
→ The LED indicator on earbuds will light up white for 1 second.
To power off, place the earbuds in the charging case and it.
When you’re wearing the earbuds, they will not power off until out of battery. When you remove the earbuds, they will automatically power off after 30 minutes if no device is connected.
Bluetooth Pairing
- Open the charging case, the earbuds will automatically enter the Bluetooth pairing mode.
→ The LED indicator on one earbud will flash quickly and on another earbud breathe slowly. - Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.
→ When successfully connected, the LED indicator on earbuds will light up white for 1 second.
- Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range.
- Mono mode: When Bluetooth connected, you can use either one of the earbuds only by placing the other one into the charging case and closing it.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
- When you are on a call, place either one of the earbuds into the charging case and close it, the microphone in the other earbud will be activated.
Pairing with another device
- Place the earbuds in the charging case and leave the case open. Press and hold the button on the case for 3 seconds until the earbud LED indicators flash white to enter the pairing mode.
- Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.
Controls
 |
|
| Play/Pause | Tap twice (R) |
| Next track | Tap twice (L) |
 |
|
| Answer a call | Tap twice (L/R) |
| Answer a second incoming call and put the current call on hold | |
| End/Reject a call | Press and hold for 2 seconds (L/
R) |
| Switch between a call on hold and an active call |
 |
|
| Switch ambient sound modes
(Noise Cancellation/Normal) |
Press and hold for 2 seconds (L/
R) |
| Mono mode | |
| Play/Pause | Tap twice |
| Answer a call | |
| End/Reject a call | Press and hold for 2 seconds |
| Activate Siri or other voice assistant software |
- All of the controls in stereo mode can be customized in the Soundcore app. In mono mode, controls cannot be customized in the app.
- Music playback will auto-pause when removing the earbuds, wear them again to resume.
- Adjust the volume level via the connected device or in the Soundcore app.
- In stereo mode, noise cancellation mode is set by default. Each time you power on and connect, or switch to the stereo mode from mono mode, your earbuds will restore the last setting.
- Noise cancellation or transparency mode is unavailable in mono mode.
Reset
You might need to reset your earbuds if you experience any connectivity problems or function issues.
- Place the earbuds in the charging case and leave the case open.
- Press and hold the button on the case for 10 seconds until the earbud LED indicators flash red 3 times and then turn white.
- Wait until the LED indicator on one of the earbuds flashes fast while the other breathes slowly. This confirms that the reset was successful and your earbuds can be connected normally.
The following two examples indicate the reset has not been successful and the previous steps should be repeated.
- If only one earbud LED indicator flashes;
- If both earbud LED indicators flash quickly.
Specifications
Specifications are subject to change without notice.
| Input | 5 V  0.5 A |
| Rated output power | 5 mW @ 1% THD |
| Battery capacity | 55 mA x 2 (earbuds); 500 mA (charging case) |
| Charging time | 2 hours 15-minute charge = 3-hour playtime |
| Playtime (varies by volume level and content) |
Up to 7 hours (Total 26 hours with the charging case) |
| Playtime (with ANC mode turned on) | Up to 6 hours (Total 21 hours with the charging case) |
| Playtime (with transparency mode turned on) | Up to 6.5 hours (Total 23 hours with the charging case) |
| Talk time | Up to 4 hours (Total 14 hours with the charging case) |
| Driver size | 11 mm |
| Frequency response | 20 Hz – 20 kHz |
| Impedance | 16 Ω |
| Waterproof level
(The waterproof level may reduce over time as a result of daily use) |
IPX4 (The earbuds are not designed for swimming, showering, or exposure to pool or ocean water. Do not use in a sauna or steam room. The charging case is not waterproof. ) |
| Bluetooth version | V 5.0 |
| Bluetooth range | 10 m / 33 ft |
More Manuals From Soundcore
(Ocr-Read Summary of Contents of some pages of the Soundcore Liberty Air 2 Pro Document (Main Content), UPD: 27 February 2023)
-
133, 131 SV 1 2 Soundcore Liberty Air 2 Pro Soundcore Liberty Air 2 Pro 3” Kontroller Spela upp/pausa Tryck två gånger (R) Nästa spår Tryck två gånger (L) Svara på ett samtal Tryck två gånger (L/R) Svara ett andra inkommande samtal och parkera det aktuella samtalet Avsluta/avvisa ett samtal Håll intryckt i 2 sekunder (Vänster/höger) Växla mellan ett parkerat och ett aktivt samtal Växla läge för omgivande ljud …
-
60, HU 58 Soundcore App Download the Soundcore app to enhance your experience. HearID: A HearID leképezi a felhasználó különböző frekvenciákra érvényes egyéni hallásérzékenységét, majd elemzi az eredményeket. Testre szabja a hangszínszabályzó beállításokat, és egyéni hangprolt hoz létre a felhasználó számára. A felhasználói felület személyre szabása: Sztereó módban minden vezérlő (például a hangerő szabályo…
-
78, NL 76 Monomodus Afspelen/pauzeren Tik twee keer Een oproep beantwoorden Een oproep beëindigen/weigeren Houd 2 seconden ingedrukt Siri of andere spraakbesturingssoftware activeren • Alle bedieningselementen in de stereomodus kunnen in de Soundcore-app worden aangepast. In de monomodus kunnen de bedieningselementen niet worden aangepast in de app. • Het afspelen van muziek wordt automatisch gepauzeerd wanneer u de oordopjes uitdoet. Doe ze weer in om het afspel…
-
109, RU 107 Приложение Soundcore Загрузите приложение Soundcore, чтобы расширить возможности работы с устройством. HearID: HearID определяет чувствительность вашего слуха в различных диапазонах частот и анализирует результаты. Приложение на…
-
45, 43 FI Lataaminen • Poista nappikuulokkeiden suojakalvo ennen ensimmäistä käyttökertaa. • Kuivaa nappikuulokkeet ja USB-portti täysin ennen lataamista. • Käytä sertioitua USB-C-latauskaapelia ja laturia välttääksesi vauriot. • Lataa molemmat nappikuulokkeet ja latauskotelo täysin ennen ensimmäistä käyttökertaa. 1. Laita nappikuulokkeet latauskoteloon ja sulje se. Latauskotelon ensimmäinen…
-
39, ES 37 Aplicación Soundcore Descargue la aplicación Soundcore para disfrutar de una mejor experiencia. HearID: HearID mapea su sensibilidad personal de audición a diferentes frecuencias y analiza los resultados. Rastrea la configuración de EQ y crea un perfil de sonido personalizado para usted. Personalización de la interfaz de usuario: En modo estéreo, todos los controles (p. ej., ajuste del volumen, control de reproducción, activar Siri) se pueden personalizar e…
-
37, Soundcore Liberty Air 2 Pro 35 EL Στα παρακάτω δύο παραδείγματα υποδεικνύεται ότι η επαναφορά δεν ολοκληρώθηκε με επιτυχία και ότι πρέπει να επαναλάβετε τα προηγούμενα βήματα. • Αν αναβοσβήσει ο ενδείκτης LED μόνο στο ένα ακουστικό • Αν οι ενδείκτες LED και στα δύ…
-
58, 56 FR faut répéter les étapes précédentes : • Si le voyant LED d’un seul écouteur clignote ; • si le voyant des deux écouteurs clignote rapidement. Spécifications Les spécications sont susceptibles d’être modiées sans préavis. ENTRÉE 5 V 0,5 A Puissance de sortie nominale 5 mW @ 1 % THD Capacité de la batterie 2 x 55 mA (écouteurs) ; 500 mA (étui de charge) Temps de charge 2 heures 1…
-
13, CS 11 Párování Bluetooth 1. Otevřením nabíjecího pouzdra sluchátka automaticky vstoupí do režimu párování Bluetooth. LED kontrolka na jednom sluchátku bude rychle blikat a na druhém sluchátku bude blikat pomalu. 2. Výběrem „Soundcore Liberty Air 2 Pro“ v seznamu Bluetooth na zařízení se připojíte. Po úspěšném připojení bude LED kontrolka na sluchátkách po dobu 1 sekundy sv…
-
15, CS 13 Mono režim Přehrát / pozastavit Klepněte dvakrát Přijmout hovor Ukončit/Zamítnout hovor Stiskněte a podržte 2 sekundy Aktivovat Siri nebo jiného softwa rového hlasového asistenta • Všechny ovládací prvky ve stereo režimu lze přizpůsobit pomocí aplikace Soundcore. V mono režimu nelze ovládací prvky přizpůsobit v aplikaci. • Přehrávání hudby se automaticky pozastaví, když si sluchátka sundáte. Chcete-li pok…
-
166, 164 TC 穿戴 1.最適合您耳朵的液態矽膠耳塞。 2.將耳機塞入您的耳道並輕輕轉動，直到您找到最舒適的牢固位置。 21 XL MM+ XS XXS XXXSS LL+ 您的耳機隨附多副耳塞套，並已預先裝上中尺寸的耳塞套。 開啟/關閉電源 打開充電盒將可自動啟動耳機。 耳機上的LED指示燈將會亮起白燈約1秒。 將耳機放入充電盒�…
-
128, Soundcore Liberty Air 2 Pro 126 SL • Če utripa samo en LED-indikator ušesne slušalke; • Če LED-indikatorja na obeh slušalkah utripata hitro. Tehnične značilnosti Tehnične značilnosti se lahko spremenijo brez predhodnega opozorila. Vhodna moč 5 V 0,5 A Ocenjena izhodna moč 5 mW @ 1 % THD Zmogljivost baterije 55 mA x 2 (ušesni slušalki); 500 mA (etui za polnjenje) Čas polnjenja 2 ura 15-minutno polnjenje = 3 uri predvajanja Čas predvajanja (odvisen od ravni glasnosti in vse…
-
74, NL 72 Soundcore-app Download de Soundcore-app voor een betere productervaring. HearID: HearID brengt uw persoonlijke gehoorgevoeligheid op meerdere frequenties in kaart en analyseert de resultaten. Het gaat de EQ-instellingen na en maakt een persoonlijk geluidsproel voor u. Aanpassing van de gebruikersinterface: in de stereomodus kan de volledige bediening (bijv. voor het instellen volume, bedienen van afspelen en activeren van Siri) worden aangepast in de app. EQ-instell…
-
110, 108 RU Ношение 1. Выберите насадки на наушники из жидкого силикона, подходящие вам лучше всего. 2. Вставьте наушники в ушной канал и аккуратно поворачивайте их, пока не найдете наиболее удобное и надежное положение. 21 XL MM+ XS XXS XXXSS LL+ На наушники установлены насадки среднего р�…
-
33, 31 EL Διαδικασία χρήσης 1. Επιλέξτε τα βύσματα υγρής σιλικόνης που ενδείκνυνται για τα αυτιά σας. 2. Περάστε τα ακουστικά μέσα στο εσωτερικό κανάλι των αφτιών σας και περιστρέψτε τα απαλά ώσπου να βρείτε τη θέση που σας βολεύει �…
-
69, IT 67 Associazione Bluetooth 1. Aprire la custodia di ricarica e gli auricolari entreranno automaticamente nella modalità di associazione Bluetooth. L’indicatore LED su un auricolare lampeggerà rapidamente e sull’altro lampeggerà lentamente. 2. Selezionare “Soundcore Liberty Air 2 Pro” dall’elenco dei dispositivi Bluetooth per procedere con il collegamento. Una volta effettuata correttamente la connessione, l’indicatore LED sugli auricolari si illuminerà di b…
-
106, Soundcore Liberty Air 2 Pro BR 104 Modo mono Reproduzir/Pausar Toque duas vezes Atender uma chamada Encerrar/rejeitar uma chamada Mantenha pressionado por 2 segundos Ativar a Siri ou outro software de assistente por voz • Todos os controles no modo estéreo podem ser personalizados no aplicativo Soundcore. No modo mono, os controles não podem ser personalizados no aplicativo. • A reprodução de música pausará automaticamente ao remover os fones de ouvid…
Released by Soundcore, the Soundcore Liberty Air 2 Pro have gained popularity among users thanks to its specifications, as well as Bluetooth 5.0, SBC, AAC, an 11mm driver size, 6-hour battery life, and up to 21 hours with the case, the IPX4 splash-resistant certification and more. Today we are going to show you how to use them in this Soundcore Liberty Air 2 Pro Manual.
What’s Inside
Soundcore Liberty Air 2 Pro Manual | Everything You Need To Know!
Soundcore Liberty Air 2 Pro Manual | How to Pair / Connect?
To iOS and Android phones
Step 1: Take the earbuds out of the charging case. They will turn on and pair to each other automatically and a LED light will flash quickly on one earbud and slowly on the other earbud.
Step 2: Turn on the Bluetooth on the desired device.
Step 3: Go to the Bluetooth settings.
Step 4: Select the “Soundcore Liberty Air 2 Pro”. If a password is needed, type “0000”.
Step 5: After that, the pairing will be done.
To PC (Windows)
Step 1: Turn on Window’s Bluetooth.
Step 2: Go to the settings.
Step 3: Go to “Bluetooth and other devices”.
Step 4: Click on “Add device”.
Step 5: Click on Bluetooth.
Step 6: Take the earbuds out of the charging case so they turn on and pair to each other automatically.
Step 7: The earbuds by the name “Soundcore Liberty Air 2 Pro” will appear on the settings.
Step 8: Select and, after this, the earbuds will automatically connect to the desired device and will be ready to use.
Soundcore Liberty Air 2 Pro Manual | Switch between Mono and Stereo mode
The earbuds go into stereo mode automatically after being paired with each other. To enter mono mode, all you have to do is to place one of the earbuds into the charging case, and the other one will enter mono mode automatically.
Soundcore Liberty Air 2 Pro Manual | How To Wear?
Step 1: Choose the ear tips that fit your ears the best.
Step 2: Identify the left and right earbuds.
Step 3: Adjust the earbuds so that the microphone is towards the mouth.
How to Control? / How to Operate? – Instructions
- Play or pause music: Click on the touch panel on the right earbud twice.
- Play the next song: Click on the touch panel on the left earbud twice.
- Answer an incoming call: Click on the touch panel on any of the earbuds twice.
- Answer a second incoming call and put the current call on hold: Click on the touch panel on any of the earbuds twice.
- Hang up a call: Press the touch panel on any of the earbuds for 2 seconds.
- Reject an incoming call: Press the touch panel on any of the earbuds for 2 seconds.
- Switch between a call on hold and an active call: Press the touch panel on any of the earbuds for 2 seconds.
- Change ambient sound modes: Press the touch panel on any of the earbuds for 2 seconds.
Soundcore Liberty Air 2 Pro Manual | How to Charge?
Earbuds
To charge the earbuds, all you have to do is to place them into the charging case and close the lid. The earbuds will start charging automatically.
Charging Case
To charge the charging case, all you have to do is plug a 5V USB Type-C cable into the port on the charging case. It will start charging automatically.
Soundcore Liberty Air 2 Pro Manual | LED Light Status
Charging case
- One light flashing: 10% or less of battery.
- One light on: 10 to 30% of battery.
- Two lights on: 30 to 70% of battery.
- Three lights on: 70% or more of battery.
Soundcore Liberty Air 2 Pro Manual | How to Reset?
Step 1: Place the earbuds into the charging case.
Step 2: Long press the touch panel on both earbuds for 10 seconds. After that, a LED light will blink red 3 times then turn white.
Step 3: Wait until the LED light in one earbud blinks quickly while the one in the other earbud is blinking slowly. After that, the resetting will be done.
A Guide To Soundcore Liberty Air 2 Pro APP
The Soundcore Liberty Air 2 Pro can be used with an application, called Soundcore. This application is available for iOS and Android devices.
- First page: The first page of this application is the home page, where you can see the battery percentage of both earbuds, as well as the Ambient Sound, Tip Fit Test and equalizer settings and controls.
- Second page: Not only will you be able to see the controls available on the earbuds, but they can also be activated, deactivated or changed if desired.
- Third page: Here, not only can you see the types of sounds that can be used with the earbuds, but you can choose one depending on the tastes of each user.
- Fourth page: In addition to having information, this application also has the possibility of helping to make sound tests, to make sure that the earbuds work correctly.
Some Common Earbuds Problems & Troubleshooting
Problems Left / Right / One side of the earbuds have stopped working
If this happens, it may be because it is low on battery or it did not connect correctly with the device. To fix this, you can do the following:
1. Try charging the earbud that is not working or both, placing them in the charging case.
2. Try factory reset the earbuds.
If that doesn’t work, the earbud is probably faulty, and I can go for a refund or replacement of it.
See also
Left / Right / One side of the earbuds has low volume
If this happens, it may be because the earbuds are dirty or the volume is set low. To fix this, you can do the following:
1. Try cleaning the earbud using a cotton swab or carefully clean the mesh with a pin.
2. Try factory reset the earbuds.
Microphone not working
If this happens, it can be because the microphone is muted, or the earbuds are badly positioned. To fix this, you can do the following:
If the microphone is muted, check the device microphone volume. If that doesn’t work, that means that there might be a defect in the earbud, so try replacing them or get a refund.
Soundcore Liberty Air 2 Pro earbuds not connecting to Windows/laptop/PC
If the earbuds are earbuds not connecting, it can be because the Bluetooth on the computer has a pairing problem. To fix this, you can do the following:
1. Try disabling Bluetooth from nearby devices >>> then activate pairing mode of the earbuds, pair and connect earbuds from Settings >>> Bluetooth & other devices >>> Add a new device >>>> elect Bluetooth,
2. Try uninstalling and reinstalling the Bluetooth driver, or update the Bluetooth driver. All can be done in Manage >>> Device Manager, reset earbuds (if available), and then repeat the step.
3. Try resetting the earbuds as said in the pairing section above.
FAQs
Are the Soundcore Liberty Air 2 Pro waterproof?
The Soundcore Liberty Air 2 Pro have an IPX4 water-resistant rating, meaning that they can withstand splashes of water.
What is the latency of Soundcore Liberty Air 2 Pro?
Normally, the latency of the Soundcore Liberty Air 2 Pro is 160-180ms, but in gaming mode the latency is 60-80ms.
Do Soundcore Liberty Air 2 Pro have low latency/gaming mode?
Yes, the Soundcore Liberty Air 2 Pro have gaming mode.
Does Soundcore Liberty Air 2 Pro have a microphone?
Yes, the Soundcore Liberty Air 2 Pro have an integrated microphone.
Can Soundcore Liberty Air 2 Pro connect to PC and Laptop?
Yes, the Soundcore Liberty Air 2 Pro can connect to PCs, laptops, and tablets.
We hope you now know how to operate the earphone from the above Soundcore Liberty Air 2 Pro Manual. Want to know anything about the earphones? Do not hesitate to ask in the comments section.