MT8102iE series
1
Installation and Startup Guide
This document covers the installation of MT8102iE Series HMI, for the detailed specifications and
operation, please refer to Brochure and EasyBuilder Pro User Manual.
Install Environment:
NEMA Rating
The
HMI product is NEMA 4 rated (Indoor Only).
The
HMI product has been tested to conform to European CE requirements. This
Electrical
means that the circuitry is designed to resist the effects of electrical noise. This
Environment
does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
(1) Make sure that the displays are installed correctly and that the operating
limits are followed. Avoid installing units in environments where severe
mechanical vibration or shocks are present.
(2)
Do not operate the unit in areas subject to explosion hazards due to
Environmental
flammable gases, vapors or dusts.
Considerations
(3) Do not install the unit where acid gas, such as SO2 exists.
(4)
This device should be mounted in the vertical position and for use on the flat
surface enclosure.
(5)
Conform to UL508 (ISBN 0-7629-0404-6) machine safety for use in
Pollution Degree 2 Environment.
2
Unpacking the Unit
Unpack and check the delivery. If damage is found,
notify the supplier.
(1)
(2)
(5)
(3)
(6)
(4)
Installation Instruction
NOTE:
Place the operator panel on a stable
surface during installation. Dropping it or
letting it fall may cause damage.
(1) Installation Instruction, 2-sided A4 *1
(2) Human Machine Interface *1
(3) Power Connector *1
(4) Brackets & Screws *1 pack
(5) USB Stick Clamp & Tying Strap *1
(6) Fuse 1.25A/250V 5*20mm *1
Installation Instructions
3
Secure the operator panel in position, using all the fastening holes and the provided brackets
and screws. Screw Torque: 2.6 ~ 3.9 lbf.in. (For reaching waterproof effect and preventing the panel
from being deformed.)
(A)
Cutout
(B)
Type
A(mm)
B(mm)
260
202
MT8102iE
USB Stick Clamp Usage
Combining the USB Stick with the clamp and the tying strap can prevent USB stick from disconnecting
with HMI when strong vibration is present.
1. Insert the USB connector to the clamp and tie them together with the tying strap.
2. Press the spring and insert the USB stick into HMI.
4
Power Connections
5
System Settings
When HMI is powered up and displays image,
click the system setting button.
(Default System Password: 111111)
It is necessary to connect the HMI to
your network through a RJ-45 cable.
NOTE:
1. Connect positive DC line to the ‘+’ terminal and
the DC ground to the ‘-‘ terminal.
2. When using a USB cable to download project
file, please do not connect HMI with PLC and PC
simultaneously to prevent potential difference from
destroying USB ports of HMI and PC.
Go to the Network tab, you may choose
to auto get DHCP IP, or designate your
own IP.
Панель оператора Weintek MT8102iE Сенсорная 10”, TFT 16.7M цветов, 1024×600, 600 МГц 32 bit RISC процессор, встроенной памяти 128MB RAM, часы реального времени. Com1: RS-232, Com2: RS-485 2w/4w, Com3: RS-485 2w/ RS-232, Com2 и Com3 cо встроенным MPI 187,5 кб/с (связь с Siemens), 1 Ethernet порт (10/100Base-T), USB 2.0 (Host), светодиодная подсветка матрицы 50,000 часов работы
|
Срок поставки |
1-2 рабочих дня |
|
Наличие |
В наличии |
|
Снятые с производства |
Нет |
|
Артикул |
MT8102iE |
|
Код товара |
1838104 |
|
Бренд |
Weintek |
|
Тип Товара |
Панель оператора |
File Specifications:2417/2417881-mt8102ie_series.pdf file (14 Apr 2023) |
Accompanying Data:
weintek MT8102iE Series Touch terminals PDF Installation Instruction (Updated: Friday 14th of April 2023 05:43:57 PM)
Rating: 4.1 (rated by 59 users)
Compatible devices: MT8090XE Series, MAT972A1, Spider SW, Omni 3350, BL202, TMI8 V2.1, ComTerminal Flamenco, DS-K1T342 Series.
Recommended Documentation:
Manual, Installation Instruction (Text Version):
(Ocr-Read Summary of Contents of some pages of the weintek MT8102iE Series Document (Main Content), UPD: 14 April 2023)
-
1, Installation and Startup Guide This document covers the installation of MT8102iE Series HMI, for the detailed specifications and operation, please refer to Brochure and EasyBuilder Pro User Manual. Install Environment: NEMA Rating The HMI product is NEMA 4 rated (Indoor Only). Electrical Environment The HMI product has been tested to conform to European CE requirements. This means that the circuitry is designed to resist the effects of elect…
-
2, EasyBuilder Pro Software Settings Launch EasyBuilder Pro software, select your project file, press F7 shortcut key to open the download dialog box: Select Ethernet > IP tab > Enter your HMI IP > Click Download to download this project file to HMI. ( Please refer to EasyBuilder Pro User Manual for software operation details ) Communication Connections Con.B Con.A COM1/…
-
weintek MT8102iE Series User Manual
-
weintek MT8102iE Series User Guide
-
weintek MT8102iE Series PDF Manual
-
weintek MT8102iE Series Owner’s Manuals
Recommended: LX-800, GR72, CIC60, ACURA 95-7868B
Links & Tools
Operating Impressions, Questions and Answers:
в заказ
Сравнить
В избранное
в заказ
Сравнить
В избранное
- Высочайшее качество и надежность
- Диагональ: 10.1″
- Разрешение: 1024×600
- Цветность: 16.7M
- ПО: EasyBuilderPro (бесплатное)
- 3 порта RS232/RS485, Ethernet, USB host
- Удаленный доступ по VNC, FTP
Технические
характеристики панели оператора Weintek MT8102iE
Дисплей
| Диагональ экрана | 10.1 ″ |
| Разрешение | 1024×600 |
| Яркость | 350 кд/м2 |
| Контрастность | 500:1 |
| Тип подсветки | LED |
| Время жизни подсветки | 50000 час. |
| Цветность | 16.7 млн |
| Угол обзора | 70/70/80/80 |
Сенсор
| Тип сенсора | 4х проводной резистивный |
Параметры
| Процессор | 32 bits RISC Cortex A8 |
| Объем ОЗУ | 128 Мб |
| Flash (встроенный) | 0.125 Гб |
| RTC ( часы реального времени ) | Есть |
Интерфейсы
| Слот SD карты | Нет |
| USB хост | USB 2.0 x 1 |
| USB клиент | Нет |
| Ethernet | 10/100 Base-T x 1 |
| Последовательный интерфейс | Con.A: COM1 RS-485 2W, COM2 RS-485 2W/4W, COM3 RS-485 2W/4W Con.B: COM1 RS-232 4W, COM3 RS-232 2W |
| CAN Bus | Нет |
| Поддержка Modbus | RTU, ASCII, Master, Slave, TCP/IP |
| Драйвера для работы с контроллерами | Более 300 драйверов совместимых с Weintek |
| Поддержка MPI | Есть |
| HDMI | Нет |
| Встроенные динамики | нет |
Конструкция
| Материал корпуса | Пластик |
| Защитное покрытие печатной платы | Есть |
| Степень защиты лицевой панели | IP65 |
| Охлаждение | безвентиляторное |
| Посадочное отверстие | 260 x 202 мм |
| Габариты | 271 х 213 х 36.4 мм |
| Вес (нетто) | 1 кг |
| Крепление на стену | в щит |
| Комплект поставки | крепежные элементы, предохранитель, разъем питания, инструкция |
ПO
| ПО для разработки проектов | EasyBuilderPro |
| EasyAccess | optional |
| Codesys | Нет |
| Максимальный размер проекта | 22.5 Мб |
| Объем памяти для сохранения архивов в панели | 48 Мб |
Эксплуатация и хранение
| Рабочая температура | 0 ~ 50℃ |
| Температура хранения | -20 ~ 60 ℃ |
| Потребляемый ток | 650mA @ 24V DC |
| Пробивная прочность корпуса | 500 V AC (1 мин.) |
| Напряжение питания | 24 ±20% VDC |
| Развязка по питанию | Встроенная |
| Сопротивление изоляции | Более 50 MΩ при 500 V постоянного тока |
| Виброустойчивость | 10 ~ 25Гц (3 напр 2G 30 мин) |
| Относительная влажность | 10% ~ 90% (без конденсации) |
| Сертификаты | CE marked |
Габариты панели оператора Weintek MT8102iE
Габариты: 271 х 213 х 36.4 мм
Посадочное
отверстие: 260 x 202 мм
Схема
соединения Weintek MT8102iE
Название разъема:
Con.B: COM1/COM3 [RS232] 9 Pin, Male, D-sub
Тип:
DB-9 M ( Папа )
| Pin # | COM1 (RS232) | COM3 (RS232) |
|---|---|---|
| 1 | — | |
| 2 | RxD | |
| 3 | TxD | |
| 4 | ||
| 5 | GND | GND |
| 6 | ||
| 7 | RTS | TxD |
| 8 | CTS | RxD |
| 9 | GND | GND |
Название разъема:
Con.A: COM1 / COM2 / COM3 [RS485] 9 Pin, Female, D-sub
Тип:
DB-9 F ( Мама )
| Pin # | COM1 (RS485 2W) | COM2 (RS485 2W) | COM2 (RS485 4W) | COM3 (RS485 2W) | COM3 (RS485 4W) |
|---|---|---|---|---|---|
| 1 | Data-(B) | RX- | |||
| 2 | Data+(A) | RX+ | |||
| 3 | TX- | ||||
| 4 | TX+ | ||||
| 5 | GND | GND | GND | GND | GND |
| 6 | Data-(B) | RX- | |||
| 7 | Data- | TX- | |||
| 8 | Data+ | TX+ | |||
| 9 | DATA+(A) | RX+ |
Файлы для работы
с Weintek MT8102iE
Table of Contents for weintek MT8102iE Series:
-
Installation and Startup Guide This document covers the installation of MT8102iE Series HMI, for the detailed specifications and operation, please refer to Brochure and EasyBuilder Pro User Manual. Install Environment: NEMA Rating The HMI product is NEMA 4 rated (Indoor Only). Electrical Environment The HMI product has been tested to conform to European CE requirements. This means that the circuitry is designed to resist the effects of electrical noise. This does not guarantee noise immunity in severe
Questions, Opinions and Exploitation Impressions:
You can ask a question, express your opinion or share our experience of weintek MT8102iE Series device using right now.