Мицубиси грандис руководство по ремонту

Руководства по ремонту и обслуживанию Mitsubishi Grandis.

↑ Mitsubishi Grandis

Сервис-мануалы

• [MSB включен] Mitsubishi Grandis Service Manual, Technical Information Manual & Body Repair Manual, MY 2008, eng., html/pdf/png, онлайн-версия

Выбираем тип мануала в левом верхнем углу окна.

• Mitsubishi Grandis 2004 Workshop Manual, eng., pdf, онлайн-версия
• Mitsubishi Grandis 2004 Body Repair Manual, eng., pdf, онлайн-версия
• Mitsubishi Grandis 2004 Service Manual, оффлайн-версия, eng., pdf в архиве zip, 249 МБ

Исправления в сервис-мануалах

• Каталог официальных сервисных бюллетеней

To change the oil in your Mitsubishi Grandis, you will need to locate the oil drain plug underneath the engine and remove it using a wrench. Allow the oil to fully drain into a drain pan, then replace the drain plug and remove the old oil filter. Finally, install a new oil filter and refill the engine with the recommended amount and type of oil specified in the manufacturer’s manual. It is important to properly dispose of the old oil and filter according to local regulations.

To check and add transmission fluid in your Mitsubishi Grandis, start the engine and let it idle for a few minutes to warm up. Locate the transmission dipstick, usually labeled with a bright color and located near the engine. Pull out the dipstick, wipe it clean, reinsert it, and then pull it out again to check the fluid level. If the level is low, add the recommended type of transmission fluid through the dipstick tube using a funnel. Recheck the fluid level and add more if needed. Regularly checking and maintaining proper transmission fluid levels is essential for smooth shifting and prolonged transmission life.

To check the brake pads in your Mitsubishi Grandis, visually inspect the brake calipers through the wheel spokes. Look for the thickness of the brake pads; if they appear thin or worn, it is time for replacement. To replace the brake pads, remove the wheel, unbolt the caliper, and carefully slide out the old pads. Install the new pads, ensuring they are properly aligned, and reassemble the caliper. Repeat the process for each wheel. Regularly checking and replacing worn brake pads is crucial for safe braking performance.

To check the windshield wiper blades in your Mitsubishi Grandis, lift the wiper arm away from the windshield and inspect the rubber blade for signs of wear, cracks, or damage. If the blades are worn or damaged, they should be replaced. To replace the wiper blades, lift the wiper arm away from the windshield and press the release tab or button on the wiper blade assembly. Slide the old blade out and insert the new blade, ensuring it is securely in place. Gently lower the wiper arm back onto the windshield. Regularly checking and replacing worn wiper blades ensures clear visibility during inclement weather.

To check the tire pressure in your Mitsubishi Grandis, start by ensuring the tires are cold. Remove the valve stem caps on each tire and use a tire pressure gauge to measure the pressure. Compare the reading to the recommended pressure listed on the sticker located on the driver’s side door jamb or in the owner’s manual. If the pressure is low, add air until it reaches the appropriate level. Regularly checking and maintaining proper tire pressure can improve fuel efficiency, tire lifespan, and overall safety.

To diagnose and reset an engine check light in your Mitsubishi Grandis, you will need an OBD-II scanner. Connect the scanner to the OBD-II port, usually located under the dashboard on the driver’s side. Follow the scanner’s instructions to retrieve the trouble codes. These codes will indicate the specific issue causing the engine check light to illuminate. Once the issue is addressed and resolved, the engine check light can be reset using the scanner. If the issue persists or you are unsure of the cause, it is recommended to consult a professional technician or refer to the repair manual for further guidance.

To jump-start your Mitsubishi Grandis, you will need a set of jumper cables and a functional vehicle with a charged battery. Park the vehicles close enough for the jumper cables to reach both battery terminals. Connect the positive (red) cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the charged battery. Connect the negative (black) cable to the negative terminal of the charged battery, and then connect the other end to a metal, unpainted surface on the engine block of the dead vehicle. Start the functioning vehicle and let it run for a few minutes, then try starting the dead vehicle. Once started, remove the jumper cables in reverse order. It is recommended to consult the owner’s manual for specific instructions and precautions.

To replace a headlight bulb in your Mitsubishi Grandis, open the hood and locate the back of the headlight assembly. Carefully disconnect the electrical connector from the bulb, then twist and remove the bulb from its socket. Insert the new bulb into the socket, ensuring it is properly aligned, and reconnect the electrical connector. Test the headlight to ensure it is functioning correctly. It is recommended to consult the owner’s manual for specific instructions and bulb types for your Mitsubishi Grandis model.

To replace the cabin air filter in your Mitsubishi Grandis, locate the cabin air filter housing, which is usually located behind the glove compartment or beneath the dashboard. Open the housing and remove the old filter, noting its orientation for proper installation of the new filter. Insert the new filter, making sure it is securely in place, and close the housing. Regularly replacing the cabin air filter improves the air quality inside the vehicle and helps maintain the efficiency of the HVAC system.

To replace the serpentine belt in your Mitsubishi Grandis, start by locating the belt routing diagram under the hood. This diagram will guide you on the correct path for the new belt installation. Using a suitable wrench or tensioner tool, release the tension on the old belt and carefully remove it from the pulleys. Install the new belt according to the routing diagram, ensuring it is properly seated on each pulley. Double-check the belt’s alignment and tension before starting the engine. Regularly inspecting and replacing worn or damaged serpentine belts is crucial for proper operation of engine accessories.

To replace the spark plugs in your Mitsubishi Grandis, start by locating the spark plug wires or ignition coils, depending on your engine configuration. Carefully disconnect the wires or coils, then use a spark plug socket and ratchet to remove the old spark plugs. Install the new spark plugs, ensuring they are properly gapped according to the manufacturer’s specifications, and tighten them securely. Reconnect the spark plug wires or ignition coils. Regularly replacing spark plugs can improve engine performance, fuel efficiency, and overall engine health.

To reset the maintenance required light in your Mitsubishi Grandis, turn the ignition key to the «ON» position without starting the engine. Fully press and release the accelerator pedal three times within 10 seconds. The maintenance required light should then go off. If it does not, repeat the process. Resetting the maintenance required light is important to keep track of regular maintenance intervals and ensure accurate notifications for future services.

It is recommended to change the engine coolant in your Mitsubishi Grandis every 30,000 to 50,000 miles or every 2 to 3 years, whichever comes first. Over time, engine coolant can become contaminated or lose its effectiveness, leading to potential engine overheating or damage. Regular coolant changes can help maintain the cooling system’s efficiency and prevent costly repairs.

For your Mitsubishi Grandis, it is recommended to use a high-quality air filter that meets or exceeds the specifications provided by the manufacturer. The air filter helps trap dust, pollen, and other particles from entering the engine, ensuring clean air intake and optimal engine performance. Regularly inspect and replace the air filter according to the maintenance schedule outlined in the owner’s manual to maintain efficient engine operation.

Подробнейшее информационно-справочное иллюстрированное издание Руководство по ремонту Mitsubishi Chariot Grandis, Space Wagon, RVR, Space Runner (2WD & 4WD). Также в этом мануале развернуто рассмотрено устройство, руководство по эксплуатации и процедурам связанным с техническим обслуживанием Mitsubishi Chariot Grandis, Mitsubishi Space Wagon, Mitsubishi RVR, Mitsubishi Space Ranner, которые производились в период с 1997 по 2003 года. Модели оборудованы бензиновыми двигателями 4G93 (объем 1,8 л. GDI), 4G63 (2,0 л. Turbo), 4G64 (2,4 л. GDI). Ремонт узлов и агрегатов. Эксплуатация. ТО. Устройство. Диагностика. Электрические схемы.

Руководство по эксплуатации и техническому обслуживанию автомобилей Mitsubishi Chariot Grandis 1997-2002 гг. выпуска

ISBN 978-966-1672-32-0

Справочное иллюстрированное издание Пособие по ремонту Мицубиси Грандис, устройство, руководство по эксплуатации и техническому обслуживанию Мицубиши Грандис (тип NA, семи или восьми местные) с передним или полным (4WD) приводом, которые выпускаются с 2004 года. Минивены с передним приводом, оборудуются бензиновым 4-х цилиндровым рядным двигателем с MIVEC объемом 2,4 л. (4G69, 165 л.с.), а также 4-х цилиндровыми рядными турбодизелями литражом 2,0 с непосредственным впрыском и мощностью 136 л.с. (BSY) или 140 л.с. (4НТ).
Книга является полной копией пособия от издательства Монолит

ISBN 978-5-91770-171-4