Мануал по ремонту пежо 605

To adjust the headlights on a Peugeot 605, park the vehicle on a level surface facing a wall or garage door. Turn on the headlights and identify the vertical and horizontal adjustment screws located behind the headlight assembly. Use a screwdriver or appropriate tool to adjust the beams until they are aligned with the desired height and direction. It is advisable to consult the owner’s manual for specific instructions and recommended alignment measurements.

To bleed the brakes on a Peugeot 605, start with the brake farthest from the master cylinder, which is usually the rear passenger-side brake. Attach a clear plastic hose to the bleeder valve and submerge the other end in a container filled with brake fluid. Have someone pump the brake pedal several times, then hold it down while you open the bleeder valve to release any air or trapped fluid. Close the bleeder valve before releasing the brake pedal and repeat the process until all air bubbles are eliminated from the system. Remember to check and refill the brake fluid reservoir regularly to avoid introducing air back into the system.

To change the oil filter on a Peugeot 605, locate the filter housing underneath the engine. Use an oil filter wrench to loosen and remove the old filter. Make sure to drain the oil completely from the engine before installing the new filter, and tighten it securely to prevent leaks.

To check the brake fluid level on a Peugeot 605, locate the brake fluid reservoir under the hood. The reservoir is typically translucent and has minimum and maximum level markings. Ensure the vehicle is parked on a level surface and remove the reservoir cap. The brake fluid level should be between the minimum and maximum markings. If the level is low, add the appropriate type of brake fluid as specified in the owner’s manual.

To replace the air filter on a Peugeot 605, locate the air filter housing, typically situated near the engine. Undo the clips or screws securing the housing and remove the old filter. Clean the housing and ensure there is no debris or dirt inside. Install the new air filter, making sure it is properly aligned, and secure the housing back in place. Regularly replacing the air filter helps maintain optimal engine performance and prolongs the life of the engine.

To replace the battery on a Peugeot 605, start by turning off the engine and removing the negative terminal, followed by the positive terminal. Carefully remove the battery hold-down clamp or bracket and lift out the old battery. Clean the battery tray and terminal connections if necessary. Place the new battery into the tray, secure it with the hold-down clamp, and reconnect the positive terminal followed by the negative terminal. Ensure the battery is properly secured to prevent any movement during driving.

To replace the fuel filter on a Peugeot 605, locate the filter, which is usually situated along the fuel line under the vehicle or inside the engine bay. Before removing the old filter, relieve the fuel system pressure by disconnecting the fuel pump fuse or relay and running the engine until it stalls. Once the pressure is relieved, disconnect the fuel lines from the old filter and remove it. Install the new filter in the same position, reconnect the fuel lines, and ensure they are properly secured. Finally, reestablish the fuel system pressure by reconnecting the fuel pump fuse or relay.

To replace the serpentine belt on a Peugeot 605, locate the belt routing diagram, which is usually found under the hood or in the owner’s manual. Use a wrench or tensioner tool to relieve the tension on the belt and slide it off the pulleys. Install the new belt by following the correct routing according to the diagram, ensuring it is properly seated on each pulley. Finally, release the tensioner to apply tension to the new belt. Inspect the belt periodically for wear and replace it if signs of cracking or fraying are present.

To replace the spark plugs on a Peugeot 605, start by disconnecting the negative battery terminal. Remove the spark plug wires from the old plugs and use a spark plug socket and extension to unscrew and remove them. Inspect the new spark plugs for proper gap and thread in the new ones, making sure to tighten them to the manufacturer’s specifications. Finally, reattach the spark plug wires and reconnect the battery.

To reset the service indicator on a Peugeot 605, turn the ignition to the «ON» position without starting the engine. Press and hold the trip reset button or the menu button on the dashboard until the service indicator starts flashing or resets. Release the button, and the service indicator should be reset. It is recommended to consult the owner’s manual for specific instructions, as the reset procedure may vary depending on the model and year of the vehicle.

Troubleshooting electrical issues on a Peugeot 605 requires a systematic approach. Start by checking the fuses and relays related to the specific electrical component or system that is malfunctioning. Inspect the wiring harnesses for any visible damage or loose connections. Use a multimeter to test the voltage and continuity at various points in the circuit. If necessary, consult the vehicle’s wiring diagrams and the repair manual for specific troubleshooting procedures and diagnostic steps. If the issue persists, it may be advisable to seek professional assistance from a qualified automotive electrician.

The recommended coolant for a Peugeot 605 is a mixture of ethylene glycol-based antifreeze and distilled water in a 50:50 ratio. This mixture provides excellent cooling and freeze protection for the engine. It is crucial to use the correct type of coolant specified by the manufacturer to prevent damage to the cooling system. Check the owner’s manual or consult a Peugeot dealership for the exact coolant specifications for your specific model.

The recommended tire pressure for a Peugeot 605 is typically between 32 and 35 PSI (pounds per square inch). It is crucial to check the tire pressure regularly, as incorrect tire pressure can affect fuel efficiency, tire wear, and handling. Refer to the owner’s manual or the tire placard located on the driver’s side door jamb for the specific recommended pressure.

If the Peugeot 605’s engine overheats, it is essential to take immediate action to prevent further damage. Safely pull over to the side of the road and turn off the engine. Allow it to cool down before opening the hood. Check the coolant level and inspect for any visible leaks. If the coolant level is low, add coolant or water if necessary. If the problem persists, it is advisable to seek professional assistance.

The recommended engine oil for a Peugeot 605 depends on the engine type and the climate conditions. It is crucial to use an engine oil with the correct viscosity and specifications for optimal engine performance and protection. Consult the owner’s manual or the oil cap for the specific oil grade recommended by the manufacturer. Additionally, it is essential to change the oil and oil filter at the recommended intervals for the best results.

Peugeot 605 с 1990 г

Сообщение nekesha » 30 дек 2014, 00:29