Мануал на кавасаки супер шерпа

• 16, LOCATION OF PARTS 15 27. Tail/Brake Light 28. Muffler 29. Air Cleaner Element 30. Seat 31. Front Brake Light Switch 32. Brake Flu id Reserv oir (Rear) 33. Rear Brake Lig ht Switch 34. Rear Brake Pedal 35. Oil Level Gauge 36. C arburetor
  …

• 76, MAINTENANCE AND ADJUST MENT 75 Frequency Whichever comes first *Odometer Reading km × 1000 ( mile × 1000) See Page Operation (Chassis Items) Every 1 (0.6) 6 (3.75) 12 (7.5) 18 (11.25) 24 (15) 30 (18.75) 36 (22.5) Brake operation (effectiveness, play, drag) — inspect year • • • • • • • 103 Brake light switch operation — inspect • • • • • • • 108 Suspensions: Rear shock absorber operati…

• 19, Kawasaki SUPER SHERPA 18 LOCATION OF LABELS 10. Noise Emission Control Information 11. Weight a nd Manufacture (For further information of label, refer to the “LABEL INFORM AT ION” chapter.)
  …

• 127, 126 MAINTENA NCE AND A DJUST MENT WARNING Special care must be taken not to get any rubber protectant on the tire’s tread surface when treat- ing tires. This may decrease the tire’s ability to maintain contact with the road surface causing the rider to lose control.
  …

• 4, Kawasaki SUPER SHERPA Whenever you see the symbols shown below, heed their instructions! Always follow safe operating and m a in- tenance practices. WARNING This warning symbol identifies special instructions or proce- dures which, if not correctly fol- lowed, could result in personal injury, or loss of life. CAUTION This caution symbol identifies special instructions or proce- dures which, if not strictly ob- served, could result in damage to or destruction of equipment. NOTE ż This note symbol indicates points…

• 87, 86 MAINTENANCE AND ADJUSTMENT NOTE ż If a torque wrench is not available, this item should be serviced by a Kawasaki dealer. CAUTION For cold weather and/or low speed riding, a hotter spark plug shown in the table may be used for quicker warm-ups and more efficient engine operation. How- ever, for normal temperatures and/or high speed use, the stan- dard spark plug must be used to prevent engine damage. Hotter Spark Plug NGK CR7E NOTE ż When ins talling t he spark plu g cap…

• 68, MAINTENANCE AND ADJUST MENT 67 MAINTENANCE AND WARRANTY Proper maintenance is necessary to ensure that your motorcycle will continue to have low emission levels. This Owner ’s Manual contains those maintenance rec- ommendations for your motorcycle. Those items identified by the Periodic Mainte- nance Chart are necessary to ensure compliance with the applicable standards. As the owner of this motorcycle, you have t…

• 66, Kawasaki SUPER SHERPA MAINTENANCE AND ADJUST MENT 65 EMISSION CONTROL INFORMATION To protect the environment in which we all live, Kawasaki has incorporated crankcase emission (1) and exhaust emission (2) control systems in compliance with applicable regulations of the United States Environmental Protection Agency. 1. Crankcase Emission Control System This system eliminates the release of crankcase vapors into the atmosphere. Instead, the vapors are routed through an oi…

• 61, 60 SAFE OPERATION braking may ca u se the motorcy cle to skid and lose control. When going down long slopes, control vehicle speed by closing the throttle. Use the front and rear brakes for a uxiliary braking. In wet conditions, rely more on the throttle to contro l vehicle speed and less on the front and rear brakes. The throttle should also be used ju- diciously to avoid skidding the rear wheel from too rapid accelerati…

• 86, MAINTENANCE AND ADJUST MENT 85 Spark Plugs The standard spark plug is shown in the table. The spark plug should be taken out in accordance with the Pe- riodic Maintenance Chart for cleaning, inspection, and resetting of the plug gap. Maintenance If the plug is oily o r has carbon built up on it, have it cleaned, preferably in a sand-blasting device, and then clean off a ny ab rasive particles. T he p lug may also be cleaned usi…

• 96, MAINTENANCE AND ADJUST MENT 95 may be damaged. Be sure to correct any of these conditions before riding. A. Idle Adjusting Screw WARNING Operation with damaged cables could result in an unsafe riding condition. Clutch Duetofrictionplatewearandclutch cable stretch over a long period of use , the clu tch must be ad justed in a ccor- dance with the Periodic Maintenance Chart. WARNING To avoid a serious burn, never touch a hot e…

• 47, Kawasaki SUPER SHERPA 46 HOW TO RIDE THE MOTORCYCLE HOW TO RIDE THE MOTORCYCLE Starting the Engine • Turnthefueltapleverto»ON»posi- tion. A. Fuel Tap Lever B. ON position NOTE ż To start a cold engine after the motor- cycle has been stored for a long time, first turn the ta p lever t o PRI, leave it for a moment, and return it to ON. • Check that the engine stop switch is in the RUN position (RUN switch pushed in). A. Engine Stop Switch B. RUN Switc h C. Starter Bu…

• 62, SAFE OPERATION 61 Daily Safety Checks Check the following items each day before you ride. The time required is minimal, and habitual performance of these checks will help ensure you a safe, reliable ride. If any irregularities are found during these checks, refer to the Maintenance and Adjustment chapter or see your dealer for the action required to return the motor- cycle to a safe operating condition. WARNING Fai…

• 14, LOCATION OF PARTS 13 LOCATION OF PARTS 1. Clutch Lever 2. Meter Instruments 3. Choke Knob 4. Brake F luid Reservoir (Front) 5. Front Brake Lever 6. Left Handlebar Switches 7. Ig nition Switch/Steering Lock 8. Right Handlebar Switch es 9. Throttle Grip
  …

• 100, MAINTENANCE AND ADJUST MENT 99 Drive C hain Slack Standard 35 ∼ 55 mm (1.4 ∼ 2.2 in.) Chain Slack Adjustment • Rem ove the cotter p in, and loos en the axle nut. • Rotate the chain adjuster at each end of the swingarm to obtain the stan- dard chain slack. A. Axle Nut B. Chain Adju ster C. Projection D. Numbers E. C otter Pin NOTE ż Wheel alignment can also be checked using the straightedge or string method.
  …

• 118, MAINTENANCE AND ADJUSTMENT 117 • Clean the battery using a solution of baking soda and water. Be sure that the lead connections are clean. Battery Installation • Put the battery in th e ba ttery cas e. • Connect the capped lead to the (+) terminal, and then connect the black lead to the (–) terminal. • Put a light coat of grease on the ter- minals to prevent corrosion. • Cover the (+) terminal with its protec- tive cap. • Reinstall the parts remov…

• 24, GENERAL INFORMATION 23 Speedometer, Odom eter/Clock, and Trip Meter: In the meter instruments face are the LCD (Liquid Crystal Display) speedometer, odometer/clock and trip meter. Pushing the odometer/clock (ODO/CLOCK) mode button shifts the display in the odometer/clock through the two modes; odometer and clock. Pushing the trip m eter A /B (TRIP A/B) mode button shifts the display in the trip m eter through the two mode s; trip A and B. When the ignition switch is turned on, all the LCD segmen…

Loading…