Korg mr 2000s инструкция на русском - Большая энциклопедия инструкций и руководств

Краткое содержание страницы № 1

Owner’s Manual
IMPORTANT NOTICE TO CONSUMERS
This product has been manufactured according to strict specifications and voltage requirements
that are applicable in the country in which it is intended that this product should be used. If you
have purchased this product via the internet, through mail order, and/or via a telephone sale, you
must verify that this product is intended to be used in the country in which you reside.
WARNING: Use of this product in any country other than that for which it

Краткое содержание страницы № 2

The lightning flash with arrowhead symbol IMPORTANT SAFETY INSTRUCTIONS within an equilateral triangle, is intended to alert the user to the presence of uninsulated • Read these instructions. “dangerous voltage” within the product’s • Keep these instructions. enclosure that may be of sufficient magnitude • Heed all warnings. to constitute a risk of electric shock to persons. • Follow all instructions. • Do not use this apparatus near water. The exclamation point within an equila

Краткое содержание страницы № 3

Contents 9. Using marks within a project …. 21 Introduction ……………………………4 Adding a mark …………………………………… 21 Features ………………………………………4 Viewing the mark list ………………………….. 22 Connection example …………………….4 Using marks to move …………………………. 22 Editing marks ……………………………………. 22 Parts of the MR-2000S ……..

Краткое содержание страницы № 4

Introduction Thank you for purchasing the Korg MR-2000S 1-bit studio recorder. In order to take full advantage of your new equipment, please read this manual carefully and use the product as directed. When you’ve read the manual, keep it safe for future reference. Features The MR-2000S is an ultra-high-quality recorder that can record and play back in DVD audio format (24- bit/192 kHz), SACD (Super Audio CD) quality format (1-bit/2.8 MHz), and in the even higher-quality 1- bit/5.6 MHz for

Краткое содержание страницы № 5

Parts of the MR-2000S Front panel 14 15 16 17 18 19 1 2 3 4 6 7 8 9 10 11 12 13 19 5 1. Power button, power LED This turns the MR-2000S on or off (standby). The power LED will light-up green when on, and red when off (standby). If you disconnect the power cable, the power will be completely off and the power LED will go dark. When you re-connect the power cable, it will take approximately one second for the unit to return to off (standby) condition. When you turn t

Краткое содержание страницы № 6

9. Display button When the home screen is shown in the display, pressing this button will switch the content shown in the counter display area (→p.17). 10. Dial Use this dial to select projects (→p.10) or ﬁles, to select parameters in various screens, and to specify values. In record-ready mode, this dial adjusts the level. 11. Stop button This button stops recording or playback 12. Playback/Pause button, Play LED This button starts recording or playback. Durin

Краткое содержание страницы № 7

Rear panel 2 4 8 9 10 1 3 5 6 7 1. AC connector Connect the power supply cable (included) here. 2. USB connector This lets you use a USB cable to connect the MR-2000S to your computer. 3. WORD CLOCK OUT jack This jack outputs the same synchronization word clock as the project (→p.10) or ﬁle. When operating in 1-bit format, this will output 44.1 kHz. 4. WORD CLOCK IN jack This jack allows the input of an external synchronization word clock in a range of 44.1 kHz – 192 k

Краткое содержание страницы № 8

Screens and operations Home screen and menu list (MENU) screen When you power-on the MR-2000S, the display will show the level meter screen. While the display is showing the home screen, pressing the menu button will show the menu list (MENU) screen which lets you proceed to various screens related to settings as well as informational screens. You’ll use the dial and enter button from this screen to select your choices. When the display shows the menu list (MENU) screen, pressing the me

Краткое содержание страницы № 9

Basic operation 1. Power and usage Plug the power cable into an AC outlet. Connect the power cable to the AC connector on the back of the MR-2000S. When you connect the power cable, the MR-2000S will enter the Off (Standby) status in approximately one second, and the power LED will light-up red. You must use only the included power cable. Using any other power cable may cause malfunctions. 2. Connecting your monitor equipment Connect your monitor system to the output jacks. You can

Краткое содержание страницы № 10

4. Playing back the demo project The MR-2000S contains a high-quality demo project that was recorded in DFF (DSDIFF) format. Here’s how to play back this project. When the MR-2000S is shipped from the factory, the clock source (→p.29) is set to Internal. What is a project? When you record on the MR-2000S, two ﬁles are created; an audio ﬁle and a project ﬁle (containing protection data and markers, etc.). These two ﬁles are collectively called a «project,» and they can be us

Краткое содержание страницы № 11

5. The home screen When you turn on the power, the home screen is shown in the display. When the menu list (MENU) screen is shown, you can also access the level meter screen by pressing the menu button. This screen shows information such as the MR-2000S’s operating status and recording/playback format. All / Shuffle indicator Playback mode indicator Repeat indicator DSD filter indicator Auto Pause indicator Input Source indicator Calendar indicator REC Lock indicator Recorder status Project/file

Краткое содержание страницы № 12

Order / total number in folder This shows the order of the projects/ﬁles within the speciﬁed folder, as well as the total number of projects/ﬁles in that folder. Project/ﬁle format This shows the format of the selected project/ﬁle (→p.28). Record/edit calendar indicator This shows the date and time at which the selected project/ﬁle was recorded or most recently edited (→p.18). Protect indicator A lock symbol is shown if the selected project is protected. Nothing is shown if the protect setting i

Краткое содержание страницы № 13

Selecting the input source Here’s how to select the input source that you want to use. The audio signal from the input jack that you specify here will be the audio that is input during record-ready mode or while recording. With the factory settings, the clock source (→p.29) is set to Internal. An error will occur if you attempt to record in 1-bit format while S/P DIF is selected. 1. Press the menu button, use the dial to select «SYSTEM» from the menu list, and press the enter but- ton to conﬁrm.

Краткое содержание страницы № 14

2. Use the dial to select the Project Type, and press the enter button to conﬁrm. A check mark will appear in the check box for the project type you selected and conﬁrmed. You can choose from WAV (BWF), DFF, DSF, and WSD. For details on each type, please refer to «Project recording format (New Project Type)» (p.28). If you’ve selected DFF, WSD, DSF If you’ve selected WAV or 3. If you checked WAV (BWF), use the dial to select the desired Wav Format: fs/bit setting (bit depth and sampling frequen

Краткое содержание страницы № 15

4. Use the dial to select the desired gain value, and press the enter button to conﬁrm. The selection icon will change from » » to » «. Perform these steps for the left and right channels. Adjust the level so that the signal does not exceed the «0» marking. When you’ve ﬁnished setting the input volume, press the exit button to return to the menu list screen, and then press the menu button once again to return to the home screen. Starting and stopping recording Each time you record on the MR-2000

Краткое содержание страницы № 16

7. Other playback/editing operations Selecting the project/ﬁle to play Use the dial to select (or choose from a list) the project/ﬁle that you want to play. When you turn on the power, the most recently selected project/ﬁle will be selected. The order of the project/ﬁles The order of the projects/ﬁles in the folder on the library select screen (LIBRARY) is listed according to the order in which they were created (FAT order), but the folders can be sorted in alphabetical order and displayed that

Краткое содержание страницы № 17

4. In the project select screen, use the dial to select a project, and press the enter button to conﬁrm. The home screen showing the newly selected project name will appear. When the display shows the home screen, you can use a shortcut to access the selection screen for the selected project/ﬁle (step 4); simply hold down the menu button for about 2 seconds. Selecting a project/ﬁle to edit Editing the selected project/ﬁle When the display shows the home screen, hold down the enter button for abo

Краткое содержание страницы № 18

Alternatively, you can press the menu button, and use the dial to select «PEAK HOLD» in the menu list (MENU) screen, and then press the enter button to conﬁrm. 2. Turn the dial to select «Meter,» and press the enter button to conﬁrm. The selection icon will change from » » to » ,» and the hold time will be highlighted. 3. Use the dial to select the desired hold time, and press the enter button to conﬁrm. The selection icon will change from » » to » .» 4. Use the dial to select «Peak LED,» and pr

Краткое содержание страницы № 19

6. When you’ve ﬁnished making settings, use the dial to select «Set» and press the enter button to con- ﬁrm. You will return to the system setting (SYSTEM) screen. If the power cable is left disconnected, the internal clock will stop operating after approximately one week. If you’ve left the power cable disconnected for an extended period of time, you’ll need to make the date and time settings again after reconnecting the power cable. The time will continue to stay while you’re setting it. Editi

Краткое содержание страницы № 20

Protecting a project Here’s how to protect a project. If you edit the mark settings of a project that is protected, these settings will revert to their original state when you select another project or turn off the power. A protected project is indicated by a protect icon displayed in the project/ﬁle information ﬁeld (the top line) of the home screen. You can’t protect an audio ﬁle that was recorded by a device other than the MR-2000S (these ﬁles will be located in the AUDIO folder). 1. Select a

Korg MR-2000S — page 1

Owner’ s Manual E E Owner’ s Manual 4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan      2008 KORG INC. 2009 AH Printed in Japan IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this produ …
Korg MR-2000S — page 2

Page 2 IMPOR T ANT SAFETY INSTR UCTIONS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Mains powered apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the appar …
Korg MR-2000S — page 3

3 Contents Introduction …………………………… 4 Features ……………………………………… 4 Connection example ……………………. 4 Parts of the MR-2000S …………………. 5 Front panel ………………………………………….5 Rear panel ………………………………………….. 7 Screens and …
Korg MR-2000S — page 4

4 Intr oduction Thank you for purchasing the Kor g MR-2000S 1-bit studio recor der . In order to take full advantage of your new equipment, please read this manual car efully and use the product as dir ected. When you’ve read the manual, keep it safe for future r eference. Features The MR-2000S is an ultra-high-quality recor der that can recor …
Korg MR-2000S — page 5

5 Pa r ts of the MR-2000S Fr ont panel 1. Power button, power LED This turns the MR-2000S on or off (standby). The power LED will light-up gr een when on, and red when off (standby). If you disconnect the power cable, the power will be completely off and the power LED will go dark. When you re-connect the power cable, it will take appr oximately on …
Korg MR-2000S — page 6

6 9. Display button When the home screen is shown in the display , pressing this button will switch the content shown in the counter display area ( → p.17). 10. Dial Use this dial to select projects ( → p.10) or ﬁles, to select parameters in various screens, and to specify values. In recor d-ready mode, this dial adjusts the level. 11 . Stop …
Korg MR-2000S — page 7

7 Rear panel 1. AC connector Connect the power supply cable (included) here. 2. USB connector This lets you use a USB cable to connect the MR-2000S to your computer . 3. WORD CLOCK OUT jack This jack outputs the same synchronization wor d clock as the project ( → p.10) or ﬁle. When operating in 1-bit format, this will output 44.1 kHz. 4. WORD C …
Korg MR-2000S — page 8

8 Screens and operations Home screen and menu list (MENU) screen When you power-on the MR-2000S, the display will show the level meter scr een. While the display is showing the home screen, pr essing the menu button will show the menu list (MENU) screen which lets you pr oceed to various screens r elated to settings as well as informational screens …
Korg MR-2000S — page 9

9 Basic operation 1. P o wer and usage Plug the power cable into an AC outlet. Connect the power cable to the AC connector on the back of the MR-2000S. When you connect the power cable, the MR-2000S will enter the Off (Standby) status in appr oximately one second, and the power LED will light-up red. Y ou must use only the included power cable. Usi …
Korg MR-2000S — page 10

10 4. Playing bac k the demo pr oject The MR-2000S contains a high-quality demo project that was r ecorded in DFF (DSDIFF) format. Her e’s how to play back this project. When the MR-2000S is shipped from the factory , the clock source ( → p.29) is set to Internal. What is a project? When you recor d on the MR-2000S, two ﬁles are cr eated; …
Korg MR-2000S — page 11

11 5. The home screen When you turn on the power , the home screen is shown in the display . When the menu list (MENU) screen is shown, you can also access the level meter screen by pr essing the menu button. This screen shows information such as the MR-2000S’s operating status and r ecording/playback format. Calendar indicator This shows the …
Korg MR-2000S — page 12

12 Order / total n umber in folder This shows the order of the pr ojects/ﬁles within the speciﬁed folder , as well as the total number of projects/ﬁles in that folder . Project/ﬁle f ormat This shows the format of the selected project/ﬁle ( → p.28). Record/edit calendar indicator This shows the date and time at which the selected projec …
Korg MR-2000S — page 13

13 Selecting the input sour ce Here’s how to select the input sour ce that you want to use. The audio signal from the input jack that you specify here will be the audio that is input during r ecord-r eady mode or while recording. W ith the factory settings, the clock sour ce ( → p.29) is set to Internal. An error will occur if you attempt to …
Korg MR-2000S — page 14

14 2. Use the dial to select the Project T ype, and press the enter button to conﬁrm. A check mark will appear in the check box for the project type you selected and conﬁrmed. Y ou can choose from W A V (BWF), DFF , DSF , and WSD. For details on each type, please r efer to «Project recor ding format (New Project T ype)» (p.28). 3. If …
Korg MR-2000S — page 15

15 4. Use the dial to select the desired gain value, and press the enter button to conﬁrm. The selection icon will change from » » to » «. Perform these steps for the left and right channels. Adjust the level so that the signal does not exceed the «0» marking. When you’ve ﬁnished setting the input volume, pres …
Korg MR-2000S — page 16

16 7. Other playbac k/editing operations Selecting the pr oject/ﬁle to play Use the dial to select (or choose from a list) the pr oject/ﬁle that you want to play . When you turn on the power , the most recently selected project/ﬁle will be selected. The order of the pr oject/ﬁles The order of the pr ojects/ﬁles in the folder on the librar …
Korg MR-2000S — page 17

17 4. In the project select screen, use the dial to select a project, and press the enter button to conﬁrm. The home screen showing the newly selected pr oject name will appear . When the display shows the home screen, you can use a shortcut to access the selection scr een for the selected project/ﬁle (step 4); simply hold down the menu button …
Korg MR-2000S — page 18

18 Alternatively , you can press the menu button, and use the dial to select «PEAK HOLD» in the menu list (MENU) screen, and then pr ess the enter button to conﬁrm. 2. T urn the dial to select «Meter ,» and press the enter button to conﬁrm. The selection icon will change from » » to » ,» and the hold time …
Korg MR-2000S — page 19

19 6. When you’ve ﬁnished making settings, use the dial to select «Set» and press the enter button to con- ﬁrm. Y ou will return to the system setting (SYSTEM) scr een. If the power cable is left disconnected, the internal clock will stop operating after approximately one week. If you’ve left the power cable disconnected for …
Korg MR-2000S — page 20

20 Pr otecting a project Here’s how to pr otect a project. If you edit the mark settings of a pr oject that is protected, these settings will r evert to their original state when you select another pr oject or turn off the power . A protected pr oject is indicated by a protect icon displayed in the pr oject/ﬁle information ﬁeld (the top li …
Korg MR-2000S — page 21

21 Viewing details about the pr oject/ﬁle Here’s how you can view detailed information about a pr oject/ﬁle. Y ou can view the audio format, song length, artist, title, date and time, and ﬁle size. 1. Select and conﬁrm the project/ﬁle whose details you want to view . Refer to «Selecting a project/ﬁle to edit» on page 17. …
Korg MR-2000S — page 22

22 Viewing the mark list Here’s how to view the list showing the marks in a pr oject in the order of their time location. 1. Select and conﬁrm the project/ﬁle whose marks you want to view . Refer to «Selecting a project/ﬁle to edit» on page 17. 2. The project/ﬁle edit screen will appear , with the name of the selected ﬁle i …
Korg MR-2000S — page 23

23 2. Use the dial to select the item that you want to edit, and press the enter button to conﬁrm. Changing the time locations of the marks Y ou can register marks in any position of the W A V , DFF or WSD project, but for the DSF pr oject, only the 1 1.6 ms (Fs=2.8 MHz) or lar ger size mark can be registered by a unit of 5.8 ms (Fs=5.6 MHz). Whe …
Korg MR-2000S — page 24

24 Deleting all marks (Delete All Mark) 1. When you use the dial to select «Delete All Mark» and press the enter button to conﬁrm, a dialog screen will ask you to conﬁrm the deletion. 2. Use the dial to select [Y es] and press the enter button to conﬁrm. If you decide not to delete the marks, use the dial to select [No] and press th …
Korg MR-2000S — page 25

25 Other functions Pla y mode The MR-2000S provides three play modes, as well as auto pause and repeat play settings. To select these modes, use «PLA Y MODE» in the menu list (MENU) screen. The icon for the selected settings will appear in the home screen (p.1 1). Single (play only one pr oject/ﬁle): (folder) / (play list) In this mode, …
Korg MR-2000S — page 26

26 Viewing a pla y list Here’s how to view the contents of a play list. 1. Press the menu button, then in the menu list (MENU) screen, use the dial to select «LIBRARY» and press the enter button to conﬁrm. The library select (LIBRARY) screen will appear . MR Project: This library contains projects recorded on the MR-2000S. Audio: T …
Korg MR-2000S — page 27

27 Remove fr om List Here’s how to remove the selected project/ﬁle fr om the play list. This will not delete the project/ﬁle itself. If you later decide to add the project/ﬁle to the play list, you can use the Add to Play List operation to do so. 1. In the play list (PLA Y LIST) screen, use the dial to select the project/ﬁle that you w …
Korg MR-2000S — page 28

28 Recor d mode Here you can adjust various settings related to recording. Press the menu button, and in the menu list (MENU) screen, use the dial to select «REC MODE» and then press the enter button to conﬁrm. Y ou can adjust the following settings fr om the recor d mode (REC MODE) screen. Project recor ding f ormat (New Pr oject T ype …
Korg MR-2000S — page 29

29 System setting (SYSTEM) Here you can adjust various system settings for the MR- 2000S itself. Press the menu button to access the menu list (MENU) screen, use the dial to select «SYSTEM,» press the enter button to conﬁrm, and then adjust the settings as described her e. LCD Contrast Here you can set the LCD contrast. Higher settings …
Korg MR-2000S — page 30

30 2. T urn the dial to select the desired value, and press the enter button to complete the setting. The selection icon will change from » » to » .» Mark mode setting (Mark Mode) Here you can specify the mark mode that will be used during r ecor ding. This setting does not af fect the marks that you reg- ister during playback. …
Korg MR-2000S — page 31

31 Project name setting (Pr oject Name) Here’s how to assign the name for the project folder that is automatically created each time you record. Default Name: The name will be «ﬁle type (p.34)_0001—9999.» Examples: DFF_0001, W A V_0001, etc. UserName: The name will be UserName0001—9999. Y ou can use up to eight characters to spec …
Korg MR-2000S — page 32

32 Updating the software (SoftwareUpdate) Y ou can download the latest version of the softwar e update system ﬁles from the Korg website (www .korg.com). For details on the procedure, refer to the Kor g website. Preparing for the update Use a USB cable to connect the MR-2000S to your com- puter (see «Using the MR-2000S with your computer &qu …
Korg MR-2000S — page 33

33 Using the MR-2000S with y our computer Y ou can use the MR-2000S as a USB 2.0 mass storage class device. This lets you copy ﬁles from the MR-2000S to your computer , or copy ﬁles (W A V , DSDIFF , etc.) from your computer into the MR-2000S There are limitations on the audio ﬁles that the MR-2000S can r ecognize (p.33). USB mode In this mod …
Korg MR-2000S — page 34

34 Supported folders and ﬁle names FA T32 ﬁle system format. Long ﬁle names are supported, double-byte characters (e.g., Japanese) are not supported. MR_PROJ folder This folder contains folders recorded on the MR-2000S, organized by date. Don’t use your computer to delete or rename the MR_PROJ folder . If you do so, the MR-2000S will no …
Korg MR-2000S — page 35

35 Files inside the DFF_0001 folder (pr oject folder) DFF_0001.prj (project settings ﬁle) This is a ﬁle speciﬁc to the MR-2000S, containing infor — mation (protect setting, mark data, etc.) for each r ecor ded project. Only one ﬁle with this extension (.prj) can exist in each project folder . DFF_0001_001.dff (audio data ﬁ le: dff) These …
Korg MR-2000S — page 36

36 Appendix Tr oubleshooting Po wer does not turn on • Is the power cable correctly connected? • Is the power LED lit green? → If the power LED is lit red, the MR-2000S is in standby mode. Press the power button to turn it on ( → p.9). Nothing appears in the displa y • Is the contrast adjusted correctly? ( → p.29) No sound • Is the MR …
Korg MR-2000S — page 37

37 V arious messages The message dialog box will disappear when you press the enter button or the exit button. Execution message Completed • The operation has been successfully completed. W orking… • The operation is being carried out. Please wait until this message disappears. Error messa g es Check Sum Error . • The software update has fa …
Korg MR-2000S — page 38

38 Normally , a minimum of ten minutes of contiguous free space will be allocated if there is ten minutes or more free capacity; if there is less than ten minutes of free capacity , as much as exists will be allocated. It is not necessarily the case that the «Disk too busy .» error will always occur if this warning appears, but we recomme …
Korg MR-2000S — page 39

39 Main speciﬁcations Frequency response:10 Hz … 20 kHz ± 1 dB @ Fs 44.1 kHz / 48 kHz 10 Hz … 40 kHz ± 1 dB @ Fs 88.2 kHz/96 kHz/ 176.4 kHz/ 192 kHz 10 Hz … 100 kHz (1-bit) S/N : 103 dB (typical) @ IHF-A THD+N : 0.005% (typical), 20 Hz … 20 kHz A/D conversion : 2.8224 MHz/5.6448 MHz(1-bit), 24bit (PCM) D/A conversion : 2.8224 MHz/5.6448 …
Korg MR-2000S — page 40

40 Inde x A All 25 All/Shuffle indicator 11 A udio 16 A udio file 33 A udio f older 35 A udioGate 35 A uto pause 25 A uto pause indicator 11 C Calendar 18 Calendar indicator 11 Clock 18 Clock source 29 Counter 12 Counter mode 17 Current project/file 11 D Def ault name 31 Delete all mark 24 mark 23 Delete project 20 Demo project 1 0 , 39 Detail proj …
Korg MR-2000S — page 41

41 Recording 12 Recording f o r mat 1 3 , 28 Recording time 28 Ref erence le vel 29 Rename 19 Repeat 25 Repeat indicator 11 Reset 31 Rewind 10 S Selecting the project 16 Shuffle 25 Single 25 Specification 38 Synchronization 29 System 29 T TOT A L 17 T otal n umber 12 TOT AL REMAIN 17 T roub leshooting 36 U Update 32 USB mode 33 User name 31 W WAV ( …
Korg MR-2000S — page 42

Owner’ s Manual E E Owner’ s Manual 4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan      2008 KORG INC. 2009 AH Printed in Japan IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this produ …

Источник

Contents
Table of Contents
Troubleshooting
Bookmarks

Quick Links

Related Manuals for Korg MR-2000S

Summary of Contents for Korg MR-2000S

Page 1
Owner’s Manual…
Page 2: Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Mains powered apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
Page 3: Table Of Contents

Introduction … 4 Features …4 Connection example …4 Parts of the MR-2000S …5 Front panel …5 Rear panel …7 Screens and operations …8 Home screen and menu list (MENU) screen …8 Selecting parameters and setting values …8 Basic operation … 9 1.
Page 4: Introduction

Thank you for purchasing the Korg MR-2000S 1-bit studio recorder. In order to take full advantage of your new equipment, please read this manual carefully and use the product as directed. When you’ve read the manual, keep it safe for future reference.
Page 5: Parts Of The Mr-2000S

Front panel Power button, power LED This turns the MR-2000S on or off (standby). The power LED will light-up green when on, and red when off (standby). If you disconnect the power cable, the power will be completely off and the power LED will go dark.
Page 6
( → p.10) or ﬁle, this LED will blink rapidly. 13. Record button, Record LED This button puts the MR-2000S in record-ready mode; recording will begin when you then press the play/pause button (record LED lit).
Page 7: Rear Panel

Connect the power supply cable (included) here. USB connector This lets you use a USB cable to connect the MR-2000S to your computer. WORD CLOCK OUT jack This jack outputs the same synchronization word clock as the project ( → p.10) or ﬁle.
Page 8: Screens And Operations

Selecting parameters and setting values On the MR-2000S, you can select parameters and set values by turning the dial and pressing the enter but- ton. The item you’ve selected by turning the dial is indicated on the screen by the movement of the » » or «…
Page 9: Basic Operation

Plug the power cable into an AC outlet. Connect the power cable to the AC connector on the back of the MR-2000S. When you connect the power cable, the MR-2000S will enter the Off (Standby) status in approximately one second, and the power LED will light-up red.
Page 10: Playing Back The Demo Project

When you record on the MR-2000S, two ﬁles are created; an audio ﬁle and a project ﬁle (containing protection data and markers, etc.). These two ﬁles are collectively called a «project,» and they can be used on the MR-2000S as if they were a single audio ﬁle. ( → p.33 «Hard disk structure and ﬁles») Playing back…
Page 11: The Home Screen

This shows the name of the selected project/ﬁle, the artist, and title information. Artist and title information cannot be entered on the MR-2000S. This will show the information spec- iﬁed by the included AudioGate software or other editing software, or the information entered on a recording device that allows such entry.
Page 12: Recording

WAV-0001 (Project folder) DFF-0002 (Project folder) DFF-0001 (Project folder) You are free to edit this name after recording (→p.19). On the MR-2000S, each of these project folders is handled in the same way as an audio ﬁle. 2008-07-25 (Folder) WAV-0002 (Project folder)
Page 13: Selecting The Input Source

S/P DIF. However, the clock source that you speciﬁed will be preserved, and will return to that speciﬁed setting when the MR-2000S is stopped or playing. When you’ve ﬁnished setting the recording mode, press the exit button to return to the menu list screen, and then press the menu button to return to the home screen.
Page 14: Adjusting The Input Level

2. Use the dial to select the Project Type, and press the enter button to conﬁrm. A check mark will appear in the check box for the project type you selected and conﬁrmed. You can choose from WAV (BWF), DFF, DSF, and WSD. For details on each type, please refer to «Project recording format (New Project Type)»…
Page 15: Starting And Stopping Recording

Starting and stopping recording Each time you record on the MR-2000S, a folder is created containing an audio ﬁle and a settings ﬁle, collec- tively called a «project.» The folder is named automatically (→p.34).
Page 16: Other Playback/Editing Operations

In order of creation Selecting a project/ﬁle using the dial When the display shows the home screen while the MR-2000S is either playing or stopped, you can turn the dial to select a project/ﬁle within the selected folder or play list.
Page 17: Selecting A Project/File To Edit

4. In the project select screen, use the dial to select a project, and press the enter button to conﬁrm. The home screen showing the newly selected project name will appear. When the display shows the home screen, you can use a shortcut to access the selection screen for the selected project/ﬁle (step 4);…
Page 18: Setting The Date And Time

Alternatively, you can press the menu button, and use the dial to select «PEAK HOLD» in the menu list (MENU) screen, and then press the enter button to conﬁrm. 2. Turn the dial to select «Meter,» and press the enter button to conﬁrm. The selection icon will change from «…
Page 19: Editing The Project/File Name

6. When you’ve ﬁnished making settings, use the dial to select «Set» and press the enter button to con- ﬁrm. You will return to the system setting (SYSTEM) screen. If the power cable is left disconnected, the internal clock will stop operating after approximately one week.
Page 20: Protecting A Project

ﬁeld (the top line) of the home screen. You can’t protect an audio ﬁle that was recorded by a device other than the MR-2000S (these ﬁles will be located in the AUDIO folder).
Page 21: Viewing Details About The Project/File

Even if the ﬁle (a WAV or DSDIFF ﬁle that can be recognized by the MR-2000S) was recorded and edited by another device, you can still use marks to move through the audio ﬁle. However, you will not be able to edit the marks.
Page 22: Viewing The Mark List

You can edit the time locations of the marks shown on the mark list (Mark List) and delete the unwanted marks. You can only edit marks of a project that the MR-2000S is able to recognize. You can edit the marks even of a project whose Protect setting is on, but they will revert to their unedited state when you select a different project or turn off the power.
Page 23
2. Use the dial to select the item that you want to edit, and press the enter button to conﬁrm. Changing the time locations of the marks You can register marks in any position of the WAV, DFF or WSD project, but for the DSF project, only the 11.6 ms (Fs=2.8 MHz) or larger size mark can be registered by a unit of 5.8 ms (Fs=5.6 MHz).
Page 24
Deleting all marks (Delete All Mark) 1. When you use the dial to select «Delete All Mark» and press the enter button to conﬁrm, a dialog screen will ask you to conﬁrm the deletion. 2. Use the dial to select [Yes] and press the enter button to conﬁrm. If you decide not to delete the marks, use the dial to select [No] and press the enter button to conﬁrm (or press the exit button), and you’ll return to the mark edit select (Mark Edit) screen.
Page 25: Other Functions

When this Auto Pause setting is «On,» the icon will appear in the home screen, and when each song ﬁnishes playing, the MR-2000S will load the data of the next song and then pause. This setting is valid for all of the play modes (All, Shufﬂe All, and Repeat).
Page 26: Viewing A Play List

2. The name of the project/ﬁle you selected and conﬁrmed will appear in the project/ﬁle edit screen displayed above. Audio: This folder contains audio ﬁles recorded on a device other than the MR-2000S. → Play List: This is the play list ( p.25).
Page 27
Remove from List Here’s how to remove the selected project/ﬁle from the play list. This will not delete the project/ﬁle itself. If you later decide to add the project/ﬁle to the play list, you can use the Add to Play List operation to do so.
Page 28: Record Mode

If you’ve selected a 1-bit format, use the 1bit DSD Format: Fs setting to specify the sampling frequency. In order to synchronize with a digital audio device other than the MR-2000S, both devices must be synchronized to the same → clock ( p.29).
Page 29: System Setting (System)

WORD: Synchronize to the clock supplied to the WORD CLOCK IN jack If you choose «WORD» as the clock source when using 1-bit format, you must input 44.1 kHz. The MR-2000S will not operate correctly if anything other than 44.1 kHz is being input.
Page 30: Mark Mode Setting (Mark Mode)

«Mark Mode» and then press the enter button to conﬁrm. Device information (Device Info) Here you can view the version of the MR-2000S’s system soft- ware, the total capacity of the hard disk, the free capacity, and the number of recorded projects/ﬁles.
Page 31: Project Name Setting (Project Name)

0001.m3u in the AUDIO folder will completely be deleted (p.33 «Hard disk structure and ﬁles»). Before formatting the hard disk, be sure to check the data and back-up the necessary data (p.33 «Using the MR-2000S with your computer»). If a power failure or similar accident occurs during format- ting, the MR-2000S may become inoperable.
Page 32: Updating The Software (Softwareupdate)

Korg website. Preparing for the update Use a USB cable to connect the MR-2000S to your com- puter (see «Using the MR-2000S with your computer» on page 33), and copy the downloaded system ﬁle to the root folder of MR-2000S’s hard disk.
Page 33: Using The Mr-2000S With Your Computer

Using the MR-2000S with your computer You can use the MR-2000S as a USB 2.0 mass storage class device. This lets you copy ﬁles from the MR-2000S to your computer, or copy ﬁles (WAV, DSDIFF, etc.) from your computer into…
Page 34
Date folders (year-month-date: e.g., 2008-07-04, etc.) A maximum of approximately 400 project folders can be created here, organized by date. The MR-2000S is only able to edit recorded ﬁles that are inside these folders. Up to 400 date folders can be recognized. If there are more than 400 project folders, they can be recognized by connecting a computer in USB mode.
Page 35: Using The Audiogate Software

«Divide» mark during recording. Using the AudioGate software The audio ﬁles of a project recorded on the MR-2000S can be copied to your computer. Then you can use the «AudioGate» audio format conversion application on the included CD to convert the audio ﬁle format;…
Page 36: Appendix

Power does not turn on • Is the power cable correctly connected? • Is the power LED lit green? → If the power LED is lit red, the MR-2000S is in standby mode. Press the power button to turn it on → p.9).
Page 37: Various Messages

Drive Error. • An error occurred while accessing the drive. → Use USB mode to connect the MR-2000S to your computer and execute the Check Drive command. If this error message appears even after you’ve exe- cuted Check Drive, format the drive.
Page 38: Specifications

Press the enter button or exit button, and remove the cause of the error. Serious error messages Fatal: # # # # # • This will appear if the MR-2000S itself has a problem or malfunction. → If this type of message appears, make a note of the text in «# # # # #»…
Page 39: Main Specifications

Main speciﬁcations Frequency response:10 Hz … 20 kHz ± 1 dB @ Fs 44.1 kHz / 48 kHz 10 Hz … 40 kHz ± 1 dB @ Fs 88.2 kHz/96 kHz/ 176.4 kHz/ 192 kHz 10 Hz … 100 kHz (1-bit) : 103 dB (typical) @ IHF-A THD+N : 0.005% (typical), 20 Hz …
Page 40: Index

All 25 All/Shuffle indicator 11 Audio 16 Audio file 33 Audio folder 35 AudioGate 35 Auto pause 25 Auto pause indicator 11 Calendar 18 Calendar indicator 11 Clock 18 Clock source 29 Counter 12 Counter mode 17 Current project/file 11 Default name 31 Delete all mark 24…
Page 41
Recording 12 Recording format 13 Recording time 28 Reference level 29 Rename 19 Repeat 25 Repeat indicator 11 Reset 31 Rewind 10 Selecting the project 16 Shuffle 25 Single 25 Specification 38 Synchronization 29 System 29 TOTAL 17 Total number 12 TOTAL REMAIN 17 Troubleshooting 36 Update 32…
Page 42
Please also retain your receipt as proof of purchase otherwise your product may be disqualified from the manufacturer’s or distributor’s warranty. 4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan      2008 KORG INC. 2009 AH Printed in Japan…

Источник

Посмотреть инструкция для Korg MR-2000S бесплатно. Руководство относится к категории смесители, 1 человек(а) дали ему среднюю оценку 7.5. Руководство доступно на следующих языках: английский. У вас есть вопрос о Korg MR-2000S или вам нужна помощь? Задайте свой вопрос здесь

Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Korg MR-2000S.

Как лучше всего выполнять чистку смеситель?

Для удаления отпечатков пальцев лучше всего использовать слегка влажную салфетку для уборки или мягкую чистую ткань. Пыль в труднодоступных местах лучше всего удаляется потоком сжатого воздуха.

Инструкция Korg MR-2000S доступно в русский?

К сожалению, у нас нет руководства для Korg MR-2000S, доступного в русский. Это руководство доступно в английский.

Не нашли свой вопрос? Задайте свой вопрос здесь

Источник

Korg MR-2000S — page 1

Owner’ s Manual E E Owner’ s Manual 4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan      2008 KORG INC. 2009 AH Printed in Japan IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this produ …
Korg MR-2000S — page 2

Page 2 IMPOR T ANT SAFETY INSTR UCTIONS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Mains powered apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the appar …
Korg MR-2000S — page 3

3 Contents Introduction …………………………… 4 Features ……………………………………… 4 Connection example ……………………. 4 Parts of the MR-2000S …………………. 5 Front panel ………………………………………….5 Rear panel ………………………………………….. 7 Screens and …
Korg MR-2000S — page 4

4 Intr oduction Thank you for purchasing the Kor g MR-2000S 1-bit studio recor der . In order to take full advantage of your new equipment, please read this manual car efully and use the product as dir ected. When you’ve read the manual, keep it safe for future r eference. Features The MR-2000S is an ultra-high-quality recor der that can recor …
Korg MR-2000S — page 5

5 Pa r ts of the MR-2000S Fr ont panel 1. Power button, power LED This turns the MR-2000S on or off (standby). The power LED will light-up gr een when on, and red when off (standby). If you disconnect the power cable, the power will be completely off and the power LED will go dark. When you re-connect the power cable, it will take appr oximately on …
Korg MR-2000S — page 6

6 9. Display button When the home screen is shown in the display , pressing this button will switch the content shown in the counter display area ( → p.17). 10. Dial Use this dial to select projects ( → p.10) or ﬁles, to select parameters in various screens, and to specify values. In recor d-ready mode, this dial adjusts the level. 11 . Stop …
Korg MR-2000S — page 7

7 Rear panel 1. AC connector Connect the power supply cable (included) here. 2. USB connector This lets you use a USB cable to connect the MR-2000S to your computer . 3. WORD CLOCK OUT jack This jack outputs the same synchronization wor d clock as the project ( → p.10) or ﬁle. When operating in 1-bit format, this will output 44.1 kHz. 4. WORD C …
Korg MR-2000S — page 8

8 Screens and operations Home screen and menu list (MENU) screen When you power-on the MR-2000S, the display will show the level meter scr een. While the display is showing the home screen, pr essing the menu button will show the menu list (MENU) screen which lets you pr oceed to various screens r elated to settings as well as informational screens …
Korg MR-2000S — page 9

9 Basic operation 1. P o wer and usage Plug the power cable into an AC outlet. Connect the power cable to the AC connector on the back of the MR-2000S. When you connect the power cable, the MR-2000S will enter the Off (Standby) status in appr oximately one second, and the power LED will light-up red. Y ou must use only the included power cable. Usi …
Korg MR-2000S — page 10

10 4. Playing bac k the demo pr oject The MR-2000S contains a high-quality demo project that was r ecorded in DFF (DSDIFF) format. Her e’s how to play back this project. When the MR-2000S is shipped from the factory , the clock source ( → p.29) is set to Internal. What is a project? When you recor d on the MR-2000S, two ﬁles are cr eated; …
Korg MR-2000S — page 11

11 5. The home screen When you turn on the power , the home screen is shown in the display . When the menu list (MENU) screen is shown, you can also access the level meter screen by pr essing the menu button. This screen shows information such as the MR-2000S’s operating status and r ecording/playback format. Calendar indicator This shows the …
Korg MR-2000S — page 12

12 Order / total n umber in folder This shows the order of the pr ojects/ﬁles within the speciﬁed folder , as well as the total number of projects/ﬁles in that folder . Project/ﬁle f ormat This shows the format of the selected project/ﬁle ( → p.28). Record/edit calendar indicator This shows the date and time at which the selected projec …
Korg MR-2000S — page 13

13 Selecting the input sour ce Here’s how to select the input sour ce that you want to use. The audio signal from the input jack that you specify here will be the audio that is input during r ecord-r eady mode or while recording. W ith the factory settings, the clock sour ce ( → p.29) is set to Internal. An error will occur if you attempt to …
Korg MR-2000S — page 14

14 2. Use the dial to select the Project T ype, and press the enter button to conﬁrm. A check mark will appear in the check box for the project type you selected and conﬁrmed. Y ou can choose from W A V (BWF), DFF , DSF , and WSD. For details on each type, please r efer to «Project recor ding format (New Project T ype)» (p.28). 3. If …
Korg MR-2000S — page 15

15 4. Use the dial to select the desired gain value, and press the enter button to conﬁrm. The selection icon will change from » » to » «. Perform these steps for the left and right channels. Adjust the level so that the signal does not exceed the «0» marking. When you’ve ﬁnished setting the input volume, pres …
Korg MR-2000S — page 16

16 7. Other playbac k/editing operations Selecting the pr oject/ﬁle to play Use the dial to select (or choose from a list) the pr oject/ﬁle that you want to play . When you turn on the power , the most recently selected project/ﬁle will be selected. The order of the pr oject/ﬁles The order of the pr ojects/ﬁles in the folder on the librar …
Korg MR-2000S — page 17

17 4. In the project select screen, use the dial to select a project, and press the enter button to conﬁrm. The home screen showing the newly selected pr oject name will appear . When the display shows the home screen, you can use a shortcut to access the selection scr een for the selected project/ﬁle (step 4); simply hold down the menu button …
Korg MR-2000S — page 18

18 Alternatively , you can press the menu button, and use the dial to select «PEAK HOLD» in the menu list (MENU) screen, and then pr ess the enter button to conﬁrm. 2. T urn the dial to select «Meter ,» and press the enter button to conﬁrm. The selection icon will change from » » to » ,» and the hold time …
Korg MR-2000S — page 19

19 6. When you’ve ﬁnished making settings, use the dial to select «Set» and press the enter button to con- ﬁrm. Y ou will return to the system setting (SYSTEM) scr een. If the power cable is left disconnected, the internal clock will stop operating after approximately one week. If you’ve left the power cable disconnected for …
Korg MR-2000S — page 20

20 Pr otecting a project Here’s how to pr otect a project. If you edit the mark settings of a pr oject that is protected, these settings will r evert to their original state when you select another pr oject or turn off the power . A protected pr oject is indicated by a protect icon displayed in the pr oject/ﬁle information ﬁeld (the top li …
Korg MR-2000S — page 21

21 Viewing details about the pr oject/ﬁle Here’s how you can view detailed information about a pr oject/ﬁle. Y ou can view the audio format, song length, artist, title, date and time, and ﬁle size. 1. Select and conﬁrm the project/ﬁle whose details you want to view . Refer to «Selecting a project/ﬁle to edit» on page 17. …
Korg MR-2000S — page 22

22 Viewing the mark list Here’s how to view the list showing the marks in a pr oject in the order of their time location. 1. Select and conﬁrm the project/ﬁle whose marks you want to view . Refer to «Selecting a project/ﬁle to edit» on page 17. 2. The project/ﬁle edit screen will appear , with the name of the selected ﬁle i …
Korg MR-2000S — page 23

23 2. Use the dial to select the item that you want to edit, and press the enter button to conﬁrm. Changing the time locations of the marks Y ou can register marks in any position of the W A V , DFF or WSD project, but for the DSF pr oject, only the 1 1.6 ms (Fs=2.8 MHz) or lar ger size mark can be registered by a unit of 5.8 ms (Fs=5.6 MHz). Whe …
Korg MR-2000S — page 24

24 Deleting all marks (Delete All Mark) 1. When you use the dial to select «Delete All Mark» and press the enter button to conﬁrm, a dialog screen will ask you to conﬁrm the deletion. 2. Use the dial to select [Y es] and press the enter button to conﬁrm. If you decide not to delete the marks, use the dial to select [No] and press th …
Korg MR-2000S — page 25

25 Other functions Pla y mode The MR-2000S provides three play modes, as well as auto pause and repeat play settings. To select these modes, use «PLA Y MODE» in the menu list (MENU) screen. The icon for the selected settings will appear in the home screen (p.1 1). Single (play only one pr oject/ﬁle): (folder) / (play list) In this mode, …
Korg MR-2000S — page 26

26 Viewing a pla y list Here’s how to view the contents of a play list. 1. Press the menu button, then in the menu list (MENU) screen, use the dial to select «LIBRARY» and press the enter button to conﬁrm. The library select (LIBRARY) screen will appear . MR Project: This library contains projects recorded on the MR-2000S. Audio: T …
Korg MR-2000S — page 27

27 Remove fr om List Here’s how to remove the selected project/ﬁle fr om the play list. This will not delete the project/ﬁle itself. If you later decide to add the project/ﬁle to the play list, you can use the Add to Play List operation to do so. 1. In the play list (PLA Y LIST) screen, use the dial to select the project/ﬁle that you w …
Korg MR-2000S — page 28

28 Recor d mode Here you can adjust various settings related to recording. Press the menu button, and in the menu list (MENU) screen, use the dial to select «REC MODE» and then press the enter button to conﬁrm. Y ou can adjust the following settings fr om the recor d mode (REC MODE) screen. Project recor ding f ormat (New Pr oject T ype …
Korg MR-2000S — page 29

29 System setting (SYSTEM) Here you can adjust various system settings for the MR- 2000S itself. Press the menu button to access the menu list (MENU) screen, use the dial to select «SYSTEM,» press the enter button to conﬁrm, and then adjust the settings as described her e. LCD Contrast Here you can set the LCD contrast. Higher settings …
Korg MR-2000S — page 30

30 2. T urn the dial to select the desired value, and press the enter button to complete the setting. The selection icon will change from » » to » .» Mark mode setting (Mark Mode) Here you can specify the mark mode that will be used during r ecor ding. This setting does not af fect the marks that you reg- ister during playback. …
Korg MR-2000S — page 31

31 Project name setting (Pr oject Name) Here’s how to assign the name for the project folder that is automatically created each time you record. Default Name: The name will be «ﬁle type (p.34)_0001—9999.» Examples: DFF_0001, W A V_0001, etc. UserName: The name will be UserName0001—9999. Y ou can use up to eight characters to spec …
Korg MR-2000S — page 32

32 Updating the software (SoftwareUpdate) Y ou can download the latest version of the softwar e update system ﬁles from the Korg website (www .korg.com). For details on the procedure, refer to the Kor g website. Preparing for the update Use a USB cable to connect the MR-2000S to your com- puter (see «Using the MR-2000S with your computer &qu …
Korg MR-2000S — page 33

33 Using the MR-2000S with y our computer Y ou can use the MR-2000S as a USB 2.0 mass storage class device. This lets you copy ﬁles from the MR-2000S to your computer , or copy ﬁles (W A V , DSDIFF , etc.) from your computer into the MR-2000S There are limitations on the audio ﬁles that the MR-2000S can r ecognize (p.33). USB mode In this mod …
Korg MR-2000S — page 34

34 Supported folders and ﬁle names FA T32 ﬁle system format. Long ﬁle names are supported, double-byte characters (e.g., Japanese) are not supported. MR_PROJ folder This folder contains folders recorded on the MR-2000S, organized by date. Don’t use your computer to delete or rename the MR_PROJ folder . If you do so, the MR-2000S will no …
Korg MR-2000S — page 35

35 Files inside the DFF_0001 folder (pr oject folder) DFF_0001.prj (project settings ﬁle) This is a ﬁle speciﬁc to the MR-2000S, containing infor — mation (protect setting, mark data, etc.) for each r ecor ded project. Only one ﬁle with this extension (.prj) can exist in each project folder . DFF_0001_001.dff (audio data ﬁ le: dff) These …
Korg MR-2000S — page 36

36 Appendix Tr oubleshooting Po wer does not turn on • Is the power cable correctly connected? • Is the power LED lit green? → If the power LED is lit red, the MR-2000S is in standby mode. Press the power button to turn it on ( → p.9). Nothing appears in the displa y • Is the contrast adjusted correctly? ( → p.29) No sound • Is the MR …
Korg MR-2000S — page 37

37 V arious messages The message dialog box will disappear when you press the enter button or the exit button. Execution message Completed • The operation has been successfully completed. W orking… • The operation is being carried out. Please wait until this message disappears. Error messa g es Check Sum Error . • The software update has fa …
Korg MR-2000S — page 38

38 Normally , a minimum of ten minutes of contiguous free space will be allocated if there is ten minutes or more free capacity; if there is less than ten minutes of free capacity , as much as exists will be allocated. It is not necessarily the case that the «Disk too busy .» error will always occur if this warning appears, but we recomme …
Korg MR-2000S — page 39

39 Main speciﬁcations Frequency response:10 Hz … 20 kHz ± 1 dB @ Fs 44.1 kHz / 48 kHz 10 Hz … 40 kHz ± 1 dB @ Fs 88.2 kHz/96 kHz/ 176.4 kHz/ 192 kHz 10 Hz … 100 kHz (1-bit) S/N : 103 dB (typical) @ IHF-A THD+N : 0.005% (typical), 20 Hz … 20 kHz A/D conversion : 2.8224 MHz/5.6448 MHz(1-bit), 24bit (PCM) D/A conversion : 2.8224 MHz/5.6448 …
Korg MR-2000S — page 40

40 Inde x A All 25 All/Shuffle indicator 11 A udio 16 A udio file 33 A udio f older 35 A udioGate 35 A uto pause 25 A uto pause indicator 11 C Calendar 18 Calendar indicator 11 Clock 18 Clock source 29 Counter 12 Counter mode 17 Current project/file 11 D Def ault name 31 Delete all mark 24 mark 23 Delete project 20 Demo project 1 0 , 39 Detail proj …
Korg MR-2000S — page 41

41 Recording 12 Recording f o r mat 1 3 , 28 Recording time 28 Ref erence le vel 29 Rename 19 Repeat 25 Repeat indicator 11 Reset 31 Rewind 10 S Selecting the project 16 Shuffle 25 Single 25 Specification 38 Synchronization 29 System 29 T TOT A L 17 T otal n umber 12 TOT AL REMAIN 17 T roub leshooting 36 U Update 32 USB mode 33 User name 31 W WAV ( …
Korg MR-2000S — page 42

Owner’ s Manual E E Owner’ s Manual 4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan      2008 KORG INC. 2009 AH Printed in Japan IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this produ …

Краткое содержание страницы № 1

Краткое содержание страницы № 2

Краткое содержание страницы № 3

Краткое содержание страницы № 4

Краткое содержание страницы № 5

Краткое содержание страницы № 6

Краткое содержание страницы № 7

Краткое содержание страницы № 8

Краткое содержание страницы № 9

Краткое содержание страницы № 10

Краткое содержание страницы № 11

Краткое содержание страницы № 12

Краткое содержание страницы № 13

Краткое содержание страницы № 14

Краткое содержание страницы № 15

Краткое содержание страницы № 16

Краткое содержание страницы № 17

Краткое содержание страницы № 18

Краткое содержание страницы № 19

Краткое содержание страницы № 20

Korg MR-2000S — page 1

Korg MR-2000S — page 2

Korg MR-2000S — page 3

Korg MR-2000S — page 4

Korg MR-2000S — page 5

Korg MR-2000S — page 6

Korg MR-2000S — page 7

Korg MR-2000S — page 8

Korg MR-2000S — page 9

Korg MR-2000S — page 10

Korg MR-2000S — page 11

Korg MR-2000S — page 12

Korg MR-2000S — page 13

Korg MR-2000S — page 14

Korg MR-2000S — page 15

Korg MR-2000S — page 16

Korg MR-2000S — page 17

Korg MR-2000S — page 18

Korg MR-2000S — page 19

Korg MR-2000S — page 20

Korg MR-2000S — page 21

Korg MR-2000S — page 22

Korg MR-2000S — page 23

Korg MR-2000S — page 24

Korg MR-2000S — page 25

Korg MR-2000S — page 26

Korg MR-2000S — page 27

Korg MR-2000S — page 28

Korg MR-2000S — page 29

Korg MR-2000S — page 30

Korg MR-2000S — page 31

Korg MR-2000S — page 32

Korg MR-2000S — page 33

Korg MR-2000S — page 34

Korg MR-2000S — page 35

Korg MR-2000S — page 36

Korg MR-2000S — page 37

Korg MR-2000S — page 38

Korg MR-2000S — page 39

Korg MR-2000S — page 40

Korg MR-2000S — page 41

Korg MR-2000S — page 42

Quick Links

Related Manuals for Korg MR-2000S

Summary of Contents for Korg MR-2000S

Page 2: Important Safety Instructions

Page 3: Table Of Contents

Page 4: Introduction

Page 5: Parts Of The Mr-2000S

Page 7: Rear Panel

Page 8: Screens And Operations

Page 9: Basic Operation

Page 10: Playing Back The Demo Project

Page 11: The Home Screen

Page 12: Recording

Page 13: Selecting The Input Source

Page 14: Adjusting The Input Level

Page 15: Starting And Stopping Recording

Page 16: Other Playback/Editing Operations

Page 17: Selecting A Project/File To Edit