- Manuals
- Brands
- Kemppi Manuals
- Welding System
- FastMig KM 400 MVU
- Operation manual
-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
FastMig
KM 400 MVU
EN
Operating manual • English
NO
Bruksanvisning • Norsk
Related Manuals for Kemppi FastMig KM 400 MVU
Summary of Contents for Kemppi FastMig KM 400 MVU
-
Page 1
FastMig KM 400 MVU Operating manual • English Bruksanvisning • Norsk… -
Page 3
OPERATING MANUAL English… -
Page 4: Table Of Contents
CONTENTS PREFACE ………………General ……………………….Introduction ..
-
Page 5: Preface
This user manual contains important information on the use, maintenance, and safety of your Kemppi product. The technical specifications of the device can be found at the end of the manual. Please read the manual carefully before using the equipment for the first time.
-
Page 6: Introduction
INTRODUCTION The FastMig KM-series power source 400 is a MIG power source designed for demanding professional use in the three-phase network. The power source has a control panel that allows ready control of the functions of the power source and the wire feeder. Overview of the power source Front view Rear view…
-
Page 7: Installation
INSTALLATION POSITIONING OF THE MACHINE Place the machine on a firm, dry and level surface. Where possible, do not allow dust or other impurities to enter the machines cooling air flow. Preferably site the machine above floor level; for example on a suitable carriage unit. Notes for positioning the machine • The surface inclination should not exceed 15 degrees.
-
Page 8: Welding And Earthing Cables
Section 4, ‘Troubleshooting’ . If the failure cannot be eliminated, turn off the machine, and turn it on again. If the failure persists, write down any fault code that may be shown on the display and contact authorised Kemppi service agent.
-
Page 9: Use Of The Control Panel
USE OF THE CONTROL PANEL The control panel is used for controlling and monitoring the operation of the power source and the wire feeder. The buttons are used for adjusting functions. The displays and indicators reflect the operating modes of the machine. weld data DYNAMICS…
-
Page 10: Adjustment Of Mig Dynamics (Arc Force)
3.3.4 Adjustment of MIG dynamics (arc force) When you press button 3, you can adjust the MIG welding dynamics of the machine by means of the right-hand knob, 11. The welding dynamics setting affects the properties of the welding arc and the amount of spatter as follows: • The value 0 is the recommended basic setting.
-
Page 11: Setting Of Operation Parameters
3.3.11 Setting of operation parameters Button 9 also is used for changing welding parameters as follows: • Depress button 9 for at least five seconds. The set-up menu appears on display 2. • Select the parameter to adjust with the left-hand knob (10) so that the name of the parameter you want to adjust is shown on display 2.
-
Page 12: Calibration Of The Wire Feed Speed
At the same time, the device exits calibration mode and returns to basic operation mode. TROUBLESHOOTING In the event of a failure of the machine, contact an authorised Kemppi service agent. Before taking your unit for servicing, check the list below. OVERLOAD (YELLOW INDICATOR LIT) Two simultaneously operating fans cool the power source.
-
Page 13: Electric Network Overvoltage Or Undervoltage
ELECTRIC NETWORK OVERVOLTAGE OR UNDERVOLTAGE If the power source is used in an electric network with insufficient voltage (less than 300 V), the control features of the device are disabled automatically. The primary circuits of the power source are protected against power spikes. The product’s mains voltage range is broad enough to prevent overvoltage problems at up to 440 V (see Section 8, ‘Technical specifications’).
-
Page 14: Service
Other error codes: The machine can show codes not listed here. In the event of an unlisted code appearing, contact an authorised Kemppi service agent and report the error code shown. SERVICE The utilisation level of the power source and its working environment should be taken into consideration in planning the frequency of maintenance of the machine.
-
Page 15: Disposal Of The Machine
The owner of the equipment is obliged to deliver a decommissioned unit to a regional collection centre, per the instructions of local authorities or a Kemppi representative. By applying this European Directive you will improve the environment and human health.
-
Page 16: Warranty Policy
The proof must indicate the date of purchase and the manufacturing number of the unit to be repaired. The parts replaced under the terms of this warranty remain the property of Kemppi and must be returned to Kemppi if requested.
-
Page 18
Telefax +358 3 734 8398 FRANCE e-mail: myynti.fi @kemppi.com Tel +33 1 30 90 04 40 KEMPPI, TRADING (BEIJING) COMPANY, LIMITED Telefax +33 1 30 90 04 45 KEMPPI SVERIGE AB Room 420, 3 Zone, Building B, e-mail: sales.fr@kemppi.com Box 717 No.12 Hongda North Street,…
FastCool 10
User Manual
Kemppi FastCool 10 User Manual,
12 pages
ArcFeed 200
User Manual
Kemppi ArcFeed 200 User Manual,
20 pages
KempCool 10
User Manual
Kemppi KempCool 10 User Manual,
12 pages
KempCool 40
User Manual
Kemppi KempCool 40 User Manual,
14 pages
Kempact Pulse 3000
User Manual
Kemppi Kempact Pulse 3000 User Manual,
24 pages
Procool 10
User Manual
Kemppi Procool 10 User Manual,
11 pages
Procool 30
User Manual
Kemppi Procool 30 User Manual,
9 pages
KMS 300
User Manual
Kemppi KMS 300 User Manual,
16 pages
KM 300
User Manual
Kemppi KM 300 User Manual,
18 pages
MSF 53
User Manual
Kemppi MSF 53 User Manual,
32 pages
MF 33
User Manual
Kemppi MF 33 User Manual,
16 pages
MF 29
User Manual
Kemppi MF 29 User Manual,
18 pages
KMS 400 MVU
User Manual
Kemppi KMS 400 MVU User Manual,
16 pages
FastMig Pulse 350
User Manual
Kemppi FastMig Pulse 350 User Manual,
30 pages
GT02S
User Manual
Kemppi GT02S User Manual,
18 pages
SF 52W
User Manual
Kemppi SF 52W User Manual,
22 pages
MXF 63
User Manual
Kemppi MXF 63 User Manual,
36 pages
SF 51
User Manual
Kemppi SF 51 User Manual,
14 pages
KMS 400 AS
User Manual
Kemppi KMS 400 AS User Manual,
18 pages
KM 400 MVU
User Manual
Kemppi KM 400 MVU User Manual,
18 pages
File Specifications:1166/1166280-fastmig_km_400_mvu.pdf file (21 Jul 2023) |
Accompanying Data:
Kemppi FastMig KM 400 MVU Welding System PDF Operation Manual (Updated: Friday 21st of July 2023 11:58:55 PM)
Rating: 4.6 (rated by 71 users)
Compatible devices: KEMPACT MIG 2520, FastMig MXP 37 Pipe Steel, KEMPACT, FastMig MSF 53, Evo 150, FastMig M Series, 25, MTP 350.
Recommended Documentation:
Operation Manual (Text Version):
(Ocr-Read Summary of Contents of some pages of the Kemppi FastMig KM 400 MVU Document (Main Content), UPD: 21 July 2023)
-
Kemppi FastMig KM 400 MVU User Manual
-
Kemppi FastMig KM 400 MVU User Guide
-
Kemppi FastMig KM 400 MVU PDF Manual
-
Kemppi FastMig KM 400 MVU Owner’s Manuals
Recommended: PRIV, TV2710B, PAR-F27MEA-US, IAI9SE
Links & Tools
-
Electrodes can be used to within one inch of the high heat, high impact head compared with the normal three inches of the electrode that is leftover when using a typical tong-type holder.Bernard Shortstub greatly improves productivity because it is designed for quick, easy installation of electrodes and it …
Shortstub 40B 2
-
WELDMARK 225OPERATOR’ S MANUALFor Machines with Code Number 11396IM927January, 2007Safety Depends on YouLincoln arc welding and cuttingequipment is designed and builtwith safety in mind. However,your overall safety can beincreased by proper installation …and thoughtful operatio …
WELDMARK 225 IM927 35
-
MPEWM160MPEWM180MPEWM200Electric Welding Machine 1-7Elektrisches Schweißgerät 8-15Machine de soudure électrique 16-22� …
MPEWM160 69
-
ProcessesDescriptionTIG (GTAW) WeldingStick (SMAW) WeldingMIG (GMAW) WeldingEngine Driven Welding GeneratorOM-4428 215 932K2007−10Visit our website atwww.MillerWelds.comFlux Cored (FCAW) WeldingAir Carbon Arc (CAC-A)Cutting and GougingFile: Engine DriveBig Blue 500DBig Blue 600 X(Deutz-Powered) …
500D 108
Operating Impressions, Questions and Answers:
EN
NO
FastMig
KM 400 MVU
Operating manual • English
Bruksanvisning • Norsk
| Language | Type | Pages | |
|---|---|---|---|
| Dutch | User Manual | 18 | > Go to the manual |
686389
Report abuse
Libble takes abuse of its services very seriously. We’re committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we’ll investigate it and take the appropriate action. We’ll get back to you only if we require additional details or have more information to share.
Product: Kemppi FastMig KM 400
Forumrules
To achieve meaningful questions, we apply the following rules:
- First, read the manual;
- Check if your question has been asked previously;
- Try to ask your question as clearly as possible;
- Did you already try to solve the problem? Please mention this;
- Is your problem solved by a visitor then let him/her know in this forum;
- To give a response to a question or answer, do not use this form but click on the button ‘reply to this question’;
- Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Your question has been posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.