Jura impressa f70 инструкция на русском

• Page 1
  IMPRESSA F70 / F707 Instructions for use…
• Page 2
  Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip…
• Page 3
  Fig. 1 Fig. 2 Fig. 6 Fig. 7 Fig. 11 Fig. 12 Fig. 16 Fig. 17 Fig. 3 Fig. 4 Fig. 8 Fig. 9 Fig. 13 Fig. 14 Fig. 18 Fig. 5 Fig. 10 Fig. 15…
• Page 4
  Temp. max. Temp. min. Fig. 19 Fig. 20 Fig. 21…

• Page 5: Control Elements

  Control elements 1. Rotary Switch 2. Illuminated ring 3. ON / OFF symbol 4. 1 LARGE CUP symbol 21 22 23 5. 1 COFFEE symbol 6. 1 ESPRESSO symbol 7. MAINTENANCE symbol 8. START symbol 9. Display dialog system 10. Water tank with handle 11.

• Page 6: Table Of Contents

  Contents 1. Safety information ……….Warning .

• Page 7: Safety Information

  Introduction Thank you for purchasing the IMPRESSA. To ensure perfect function- ing of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or contact your local authorized dealer.

• Page 8: Fill Water Tank

  2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly.

• Page 9: Adjusting The Water Hardness

  Confirm your selection by pressing the Rotary Switch (1) (Fig. 17). FILL WATER Fill the water tank (10) with fresh water. OPEN TAP Place a receptacle under the Professional Cappuccino Frother (15) (Fig. 10). Open the steam / hot water draw-off tap (14) (Fig. 12). FILLING SYSTEM CLOSE TAP…

• Page 10: Installation Of Claris Plus Filter Cartridges

  FILTER – Turn the Rotary Switch (1) until the following message is displayed: HARDNESS Now press the Rotary Switch (1) to start the programming. LEVEL 3 Turn the Rotary Switch (1) until the required level is displayed. For example, LEVEL 4 Press the Rotary Switch (1) to confirm the required level.

• Page 11: Replacing The Filter

  HEATING UP READY Now you have activated the filter. In Programming Mode the water hardness selection function is no longer displayed. 5.2 Replacing the filter Draw off 1/2 litre of water to rinse filter completely. In order to ensure perfect operation, close tap (14) only after the display says CLOSE TAP After drawing off approx.

• Page 12: Rinsing The Impressa Without Display Request

  Touch the symbol (3). HEATING UP PRESS MAINT. Touch the symbol (7). RINSING READY 6.1 Rinsing the IMPRESSA without display request Press the Rotary Switch (1) until FILTER – / appears. Turn the Rotary Switch (1) until MAINTENANCE appears. Press the Rotary Switch (1) to confirm. RINSE Press the Rotary Switch (1) again to confirm.

• Page 13: Making 2 Cups Of Coffee

  STRONG Touch the (8) symbol 160 ML (water quantity last adjusted). The illuminated ring (2) is active. Turn the Rotary Switch (1) until the required amount of coffee water appears on the display (9). e.g. 120 ML COFFEE Your coffee is being prepared. READY 9.

• Page 14: Drawing Off Hot Water

  Open the cover of the filler funnel for pre-ground coffee (11). FILL POWDER Fill 1 or 2 level spoonfuls of pre-ground coffee in the filler funnel for pre-ground coffee (11) (Fig. 15) and close the cover. SELECT Press the required draw-off key. Touch the (8) symbol 120 ML (water quantity last adjusted)

• Page 15: Dispensing Cappuccino With The Professional Cappuccino Frother

  Make sure that the nozzle is correctly fitted when drawing steam. If the nozzle becomes blocked with particles of milk residue or is incorrectly assembled, a danger can arise during use whereby the nozzle may jump off. Due to the system design, some water will escape at first when steam is drawn.

• Page 16: Dispensing Hot Milk With The Professional Cappuccino Frother

  A useful addition is available for all lovers of milk specialities in the form of high-quality vacuum milk containers. They keep the milk cool the whole day long and are optimally suited to the design of your IMPRESSA. All original JURA accessories can be obtained from the specialist shop.

• Page 17: Cleaning The Professional Cappuccino Frother

  Thoroughly rinse all parts of the nozzle under running water. Reassemble the Professional Cappuccino Frother (15) and refit it on to your IMPRESSA. 13.4 Cleaning the Professional Cappuccino Frother To ensure that the Professional Cappuccino Frother (15) func- tions perfectly, you should clean it daily if you have prepared milk foam or hot milk.

• Page 18: Programming

  15. Programming When your IMPRESSA leaves the factory it is adjusted such that you can draw off coffee without having to change any settings. However, you can programme various para meters individually. You can programme the following stages: Filter Water hardness Maintenance Aroma Temperature…

• Page 19: Programming The Temperature

  READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until Aroma is displayed. AROMA Press the Rotary Switch (1). INTENSIVE Turn the Rotary Switch (1) until the following message is displayed: STANDARD Press the Rotary Switch (1) to save the setting.

• Page 20: Programming The Automatic Switch-On Time

  Turn the Rotary Switch (1) to select the minutes. 2:05 Press the Rotary Switch (1) to save the setting. TIME Turn the Rotary Switch (1) until EXIT appears Press the Rotary Switch (1) to leave the programming mode. READY If the machine is disconnected from power supply, the time must be programmed again.

• Page 21: Cup Counter

  Turn the Rotary Switch (1) to adjust the hours. 1.0 HR Press the Rotary Switch (1) to save the setting. OFF AFT. HR Turn the Rotary Switch (1) until EXIT appears Press the Rotary Switch (1) to leave the programming mode. READY 15.9 Cup counter This function is available with the following types of coffee:…

• Page 22: Programming Display 24H/Am/Pm

  LANGUAGE Turn the Rotary Switch (1) until EXIT appears Press the Rotary Switch (1) to leave the programming mode. READY 15.11 Programming Display 24H/AM/PM READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until DISPLAY appears Press the Rotary Switch (1)

• Page 23: Maintenance

  Press the Rotary Switch (1) to leave the programming mode. READYM 16. Maintenance 16.1 Filling in water FILL WATER If this information is displayed, drawing off products is no longer possible. Refill water as described in Chapter 2.3. READY The water tank should be rinsed daily and refilled with fresh water.

• Page 24: Cleaning The Impressa

  16.6 Cleaning the IMPRESSA After 200 draw-off operations or after 80 rinsing operations, the IM- PRESSA must be cleaned. A message appears on the display, telling you to start the cleaning programme. You can still draw off coffee or hot water/steam. However, we recommend that you should clean the machine (Chapter 17) within the next few days.

• Page 25: Cleaning

  17. Cleaning Your IMPRESSA features an integrated cleaning program. The clean- ing operation will take some 15 min. Original JURA cleaning tablets which are specially designed for the cleaning program of your IMPRESSA are available at your authorized dealer. Please note that machine defects or residues in the water cannot be excluded if you use inappropriate clean- ing agents.

• Page 26: Descaling

  Press the Rotary Switch (1) again to confirm. EMPTY TRAY The program ‘Clean’ is now active. Now proceed as described in Chapter 17 from EMPTY TRAY onwards. 18. Descaling Your IMPRESSA features an integrated descaling program. The clean- ing operation will take some 40 min. Original JURA descaling tablets which are specially designed for the descaling program of your IMPRESSA are available at your authorized dealer.

• Page 27: Decalcifying Without Display Request

  Insert the tray (20) again. FILL WATER Rinse the water tank thoroughly and fill it with cold, fresh tap water. Install it again. OPEN Open the steam / hot water draw-off tap (14) (Fig. 12). DE-SCALING CLOSE TAP After you have closed the steam / hot water draw off tap (14), the following message is displayed DE-SCALING EMPTY…

• Page 28: Tips For Perfect Coffee

  20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of your cups (Fig. 3) Grinding degree Refer to Chapter 2.5 ‘Adjusting the grinding gear’. Preheating cups You can preheat the cups using hot water or steam. The smaller the coffee you want to draw off, the more important preheating is.

• Page 29: Messages

  21. Messages Cause FILL WATER Water tank is empty. Float defective FILL BEANS Bean tank is empty. Although you have refilled beans, the message still appears. EMPTY GROUNDS Coffee grounds container full Tray reinstalled too early after emptying NO TRAY Drip tray not installed properly or missing CLEAN MACHINE / Cleaning required…

• Page 30: Problems

  22. Problems Problem Cause Very loud noise coming from the Foreign body in grinding gear grinding gear Too little foam when Professional Cappuccino Frother has frothing the milk become dirty Individual parts of the Professional Cappuccino Frother are incorrectly assembled Coffee only drips Grinding degree too fine from the coffee spout…

• Page 31: Legal Information

  23. Legal information These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover any conceivable appli — cation.

• Page 32
  JURA-Elektroapparate AG – Kaffeeweltstrasse 10 – CH-4626 Niederbuchsiten www.jura.com…

JURA IMPRESSA F70 инструкция по эксплуатации
(31 страница)