Инструкция к часам casio edifice eqs 500

Casio EQS-500 / линейка Edifice / модуль 5123 / год 2012

Инструкция к модулю Casio 5123

• Смотреть онлайн → (без скачивания, удобно на мобильных и планшетах);
• Скачать русскую инструкцию →  (типичная “как у всех”, не всегда понятные картинки);
• Скачать английскую инструкцию → (детальная, много фото, более понятная).

Сложно настроить? Спрашивай на форуме Edifice →

Читайте новости о любимых часах EQS-500 на блоге
[display-posts tag=”EQS-500″ posts_per_page=”4″]

Все новости о EQS-500 →

Побывайте на заводе Casio, изучайте последние новинки Edifice на Casioblog.RU

Страницы и текст этой инструкции

1

Operation Guide 5123

MA1004-EA

Congratulations upon your selection of this CASIO watch.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours for Newfoundland, Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage

or loss suffered by you or any third party arising through the use of this product or

its malfunction.

About This Manual

Button operations are indicated using the letters A through

D shown in the illustration.

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Upper Left Dial Hand

b Lower Left Dial Hands

n Right Dial Hand: Indicates the current mode.

m Day

This User’s Guide uses numbers shown above to identify

watch hands and indicators.

Things to check before using the watch

1. Hold down C for about two seconds to enter the Timekeeping Mode, and

then observe the movement of the

x Second Hand.

Is the x Second Hand moving smoothly at one-second intervals?

Is the x Second Hand moving at

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged sufficiently.

For details about charging, see

“Charging the Watch”.

Power is low. Charge the watch by placing

it in a location where it is exposed to light.

For details, see “Charging the Watch”.

NO

YES

YES

NEXT

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To configure Home City settings” to configure your Home

City and daylight saving time settings.

Important!

World Time settings depend on correct Home City, time, and date settings in the

Timekeeping Mode. Make sure these settings are configured correctly.

3. Set the current time.

See “Configuring Current Time and Date Settings”.

The watch is now ready for use.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated

power charges a built-in rechargeable battery, which powers watch operations. The

watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not

wearing the watch, be sure

to leave it in a location

where it is exposed to light.

Best charging •

performance is achieved

by exposing the watch to

light that is as strong as

possible.

When wearing the watch,

makes sure that its face is

not blocked from light by the

sleeve of your clothing.

The watch may enter a •

sleep state if its face is

blocked by your sleeve

even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become

particularly hot when exposed to the following conditions for long periods.

On the dashboard of a car parked in direct sunlight •

Too close to an incandescent lamp •

Under direct sunlight •

Important!

Keep the watch in an area normally exposed to bright light when storing it for long •

periods. This helps to ensure that power does not run down.

Storing the watch for long periods in an area where there is no light or wearing it in •

such a way that it is blocked from exposure to light can cause power to run down.

Make sure that the watch is exposed to bright light whenever possible.

Power Levels

You can get an idea of the watch’s power level by

observing the movement of the

x Second Hand in the

Timekeeping Mode.

If the •

x Second Hand is moving normally at one-second

intervals, power is at Level 1.

If the •

x Second Hand is moving at two-second intervals,

power is at Level 2, which is quite low. Expose the watch

to light as soon as possible so it can charge.

Moving at two-second

intervals.

Level Hand Movement Function Status

1 Normal. All functions enabled.

2

x Second Hand moving at two-second

intervals.

m Day changes to 1 (home position).

Beeper disabled.

3

x Second Hand stopped.

z Hour Hand and c Minute Hand stopped

at 12 o’clock.

All functions disabled.

When power drops to Level 3, all functions will be disabled but the watch will •

continue to keep time internally for about one week. If you recharge the battery

sufficiently during this period, the analog hands will move automatically to the

correct setting and regular timekeeping will resume. After one week, all settings

(including timekeeping) will be cleared. Recharging the battery will reset all settings

to their initial factory defaults.

Power Recovery Mode

The watch is designed to go into a power recovery mode that stops hand operation

temporarily whenever power suddenly drops below a certain level due to overuse

of the alarm tone over a short period. Note that all operations are disabled while the

watch is in the power recovery mode.

The hands will move to the correct positions and the watch will resume normal

operation after power recovers (in about 15 minutes). Putting the watch in a location

where it is exposed to light will help power to recover sooner.

Charging Times

Exposure Level (Brightness)

Daily

Operation *1

Level Change *2

Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 minutes 2 hours 27 hours

Window sunlight (10,000 lux) 30 minutes 6 hours 100 hours

Window sunlight on cloudy day

(5,000 lux)

48 minutes 10 hours – – –

Indoor fluorescent lighting (500 lux) 8 hours 112 hours – – –

1 Approximate exposure each day to generate power for normal daily operation. *

2 Approximate exposure to take power up one level. *

The above exposure times all are for reference only. Actual exposure times depend •

on lighting conditions.

For details about the operating time and daily operating conditions, see the “Power •

Supply” section of the Specifications.

Power Saving

Power Saving enters a sleep state automatically whenever the watch is left for a

certain period in an area where it is dark. The table below shows how watch functions

are affected by Power Saving.

There actually are two sleep state levels: “second hand sleep” and “function sleep”. •

Elapsed Time in Dark Operation

60 to 70 minutes (second hand

sleep)

x Second Hand only is stopped at 12 o’clock, all other

functions are enabled.

6 or 7 days (function sleep)

All functions, including analog timekeeping, disabled •

Internal timekeeping maintained. •

The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch •

is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep

state.

The watch will not enter a sleep state while it is in the Stopwatch Mode. •

To recover from the sleep state

Move the watch to a well-lit area or press any button.

Mode Reference Guide

Your watch has four “modes”. The mode you should select depends on what you

want to do.

To do this: Enter this mode:

View the current time in your Home City and in one of 29 •

cities around the globe

Configure Home City and daylight saving time (DST) •

settings

Configure time and date settings •

Timekeeping Mode

Use the stopwatch to measure elapsed time Stopwatch Mode

View the current time in one of 29 cities (time zones) around

the globe

World Time Mode

Set an alarm time Alarm Mode

Selecting a Mode

With this watch, everything starts from the Timekeeping Mode.

To determine the watch’s current mode

Check the position of the

n Right Dial Hand as shown

under “To select a mode”.

To return to the Timekeeping Mode from any other

mode

Hold down C for about two seconds until the watch beeps

twice.