- Manuals
- Brands
- Energic Plus Manuals
- Battery Charger
- RX
- User manual
-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
BATTERY CHARGER
BATTERY CHARGER
RX
RX
USER’S MANUAL
USER’S MANUAL
Related Manuals for Energic Plus RX
Summary of Contents for Energic Plus RX
-
Page 1: Battery Charger
BATTERY CHARGER BATTERY CHARGER USER’S MANUAL USER’S MANUAL…
-
Page 2
(THIS PAGE WAS INTENTIONALLY LEFT BLANK) -
Page 3: Table Of Contents
TABLE OF CONTENTS Table of Contents · GENERAL………………..4 · 1. Introduction………………….. 4 · 2. Safety instructions and warnings…………..5 · RX SINGLEPHASE………………7 · 3. Description………………….7 · 4. Installation………………….8 · 5. Operation………………….11 · RX THREEPHASE………………14 ·…
-
Page 4: General
RESPONSIBILITY DISCLAIMER The manufacturer of the Energic plus RX battery charger will not be responsible for damages and/or injuries caused by the charger in these situations: The charger is not installed properly by a qualified electrician;…
-
Page 5: Safety Instructions And Warnings
Battery Charger RX User’s Manual Safety instructions and warnings GENERAL Battery chargers can cause injury or death, or damage to other equipment or property, if the user does not strictly observe all safety rules and take precautionary actions. Safe practices must be learned through study and training before using this equipment.
-
Page 6
Battery Charger RX User’s Manual BURN AND BODILY INJURY PREVENTION The battery produces very high currents when short circuited, and will burn the skin severely if in contact with any metal conductor that is carrying this current. Do not permit rings on fingers to come in contact with battery terminals or the cell connectors on top of the battery. -
Page 7: Rx Singlephase
User’s Manual RX SINGLEPHASE Description Energic plus RX battery chargers have been designed to charge Pb batteries. These units can convert the AC input voltage to a DC voltage at the correct level, in order to charge the battery cells.
-
Page 8: Installation Of The Charger
Battery Charger RX User’s Manual 4. Installation of the charger Conditions of use: Operating temperature: 5°C to 45°C • Storage temperature: -20°C to 60°C • Relative humidity: less than 75% • CAUTION The charger can be installed by qualified personnel only.
-
Page 9
Battery Charger RX User’s Manual INTERNAL VIEW OF THE CHARGER NOTE Check the efficiency of earth circuitry (yellow/green cable); Connect the charger to the mains using an adeguate plug, with pushbutton and fuses; Use an adeguate plug to connect the charger to the battery. -
Page 10
Battery Charger RX User’s Manual ELECTRICAL INSTALLATION OF THE CHARGER Check the efficiency of earth circuitry (yellow/green wire); • Connect the charger to the mains using an adeguate plugs, with pushbutton and fuses; • Use an adeguate plug to connect the charger to the battery;… -
Page 11: Operation
Battery Charger RX User’s Manual Operation PRELIMINARY CONTROLS Inspect the charger completey for loose screws, electrical connections or other damages; • Check that all the ventilation slots are not obstructed to assure proper air flow; • Make sure that the charger is installed as instructed in this manual and in accordance with •…
-
Page 12
WARNING ! ENERGIC Plus RX chargers are programmed to do a complete cycle of charge, however it’s recommended to survey the operations when the battery must remain connected to the charger for more than 12 hours (example: week-ends) -
Page 13
The EQUALIZATION function, performed by ENERGIC Plus RX chargers, has been developed to keep all the cells of the battery at the same level, even after years of continuous work. -
Page 14: Rx Threephase
User’s Manual RX THREEPHASE Description Energic plus RX battery chargers have been designed to charge Pb batteries. These units can convert the AC input voltage to a DC voltage at the correct level, in order to charge the battery cells.
-
Page 15: Installation
Battery Charger RX User’s Manual 7. Installation Conditions of use: Operating temperature: 5°C to 45°C • Storage temperature: -20°C to 60°C • Relative humidity: less than 75% • CAUTION The charger can be installed by qualified personnel only. NOTE This unit operates on threephase AC input, 380 Vac, 50Hz.
-
Page 16
Battery Charger RX User’s Manual INTERNAL VIEW OF THE CHARGER NOTE Check the efficiency of earth circuitry (yellow/green cable); Connect the charger to the mains using an adeguate plug, with pushbutton and fuses; Use an adeguate plug to connect the charger to the battery. -
Page 17
Battery Charger RX User’s Manual ELECTRICAL INSTALLATION OF THE CHARGER Check the efficiency of earth circuitry (yellow/green wire); • Connect the charger to the mains using an adeguate plugs, with pushbutton and fuses; • Use an adeguate plug to connect the charger to the battery. -
Page 18: Operation
Battery Charger RX User’s Manual 8. Operation PRELIMINARY CONTROLS Inspect the charger completey for loose screws, electrical connections or other damages; • Check that all the ventilation slots are not obstructed to assure proper air flow; • Make sure that the charger is installed as instructed in this manual and in accordance with •…
-
Page 19
1 second. This control is useful to be sure that the electronic control is working correctly. Energic Plus RX chargers are programmed to do a complete cycle of charge, however it’s recommended to survey the operations when the battery must remain connected to the charger… -
Page 20
During extra charge cycles the LEDs “ FINAL CHARGE” and “STOP-100%” flash alternately. NOTE The operations described in this chapter are done by ENERGIC Plus RX chargers automatically. END OF CHARGE When the battery is completely charged the charger is turned off and the LED “STOP – 100%”… -
Page 21: Trouble Shooting Guide
Battery Charger RX User’s Manual TROUBLE SHOOTING GUIDE SYMPTOM POSSIBLE CAUSES ACTION 1 Battery not connected properly. Check battery connectors/harness. Charger does not Charger has been connected to Disconnect forkift motor and react to battery forklift motor connector. connect battery.
-
Page 22
Battery Charger RX User’s Manual Page 22 of 25 OWM-040906-RX Version: 02-AB… -
Page 23
Battery Charger RX User’s Manual Page 23 of 25 OWM-040906-RX Version: 02-AB… -
Page 24: Spare Parts List
COMMON PARTS – SINGLEPHASE CABINET S POSITION CODE DESCRIPTION 0203340 Base RE box S 0203341 Cover RE box S 0203129T Printcard external plate RX RLCBSRE-06-01 Printcard support (x4) 0201321 Main switch 0-1 0201829 Cable strain relief 0201828 Cable strain relief…
-
Page 25
Battery Charger RX User’s Manual COMMON PARTS – THREEPHASE POSITION CODE DESCRIPTION 0203370 Base RE box B 0203374 Cover RE box B 0203125 Printcard external plate RE RLCBSRE-06-01 Printcard support (x4) 203141 Pushbutton 0-1 0203999 Varistor 275V 100001 Output fuse holder…
Перейти к контенту
info@akbremont.ru
Отдел подбора
Стоимость и наличие уточним при оформлении заказа
Оплата
Онлайн или по счету
Описание товара
Зарядное устройство Energic Plus RX-T-T 48V 100Ah 380V. Купить недорогое зарядное устройство для тягового аккумулятора. Бренд Energic Plus — бюджетный вариант трёхфазного зарядника для классической батареи погрузчика с мощными техническими характеристиками.
Energic Plus RX-T-T 48V 100Ah 380V подойдёт для свинцово-кислотного аккумулятора с напряжением 48V и ёмкостью 500-600 Ач. Подключение в розетку 380V
Похожие товары
Технические характеристики:
| Вес | 53 kg |
|---|---|
| Габариты | 50 × 34 × 36 cm |
| Напряжение сети, V |
380В |
| Напряжение, В |
48V |
| Сила ток заряда, А |
100А |
| Бренд |
Energic Plus |
| Страна производитель |
Италия |
| Технология |
Свинцово-кислотная |
| Гарантия производителя |
24 месяца |
Похожие товары
Заполните заявку и менеджеры магазина быстро подберут нужную деталь
Трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah купить со склада в Москве
Трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah артикул 122ta8181 вы можете купить в техцентре АвтоСпецВосток с экспресс доставкой по Москве или в любой регион России.
Однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah всегда имеются в наличии на складе техцентра АвтоСпецВосток по доступным ценам в Москве.
Зарядные устройства для тяговых батарей и аккумуляторов Energic Plus
Однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah — экономичное зарядное устройство, подходит для тяговых аккумуляторов погрузчиков, штабелёров и электрокаров.
Однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah обеспечивает исключительную надежность и производительность тяговых батарей всех типов (залитые или герметичные свинцово-кислотные, гелевые, Ni-Zn), используемых на любом типе транспортного средства или портативного оборудования.
Однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah с доставкой по всей России
Вы можете купить однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah в техцентре АвтоСпецВосток с доставкой по Москве и в другие города России. Наличие собственного склада запчастей для погрузчиков в Москве обеспечивает регулярные поставки промышленных зарядных устройств Energic Plus в сжатые сроки для бесперебойной работы Вашего автопарка складской техники.
Зарядные устройства для электропогрузчиков и складского оборудования
Купить однофазное и трёхфазное зарядное устройство Energic Plus RX для тяговых аккумуляторов / батарей 48v, 380V 100A 500-600Ah по выгодным ценам в техцентре АвтоСпецВосток можно оптом и в розницу.
В каталоге производителя Energic Plus представлен ассортимент однофазных и трёхфазных зарядных устройств для электропогрузчиков, штабелёров и другой складской техники, которые работают на тяговых аккумуляторах всех типов.
Вся продукция имеется в наличии на складе в Москве, если Вы не нашли необходимое зарядное устройство для погрузчика или затрудняетесь с выбором, свяжитесь с нашим оператором для формирования заказа.
- Manuals
- Brands
- Energic Plus Manuals
- Battery Charger
- RX
- User manual
-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
BATTERY CHARGER
BATTERY CHARGER
RX
RX
USER’S MANUAL
USER’S MANUAL
Related Manuals for Energic Plus RX
Summary of Contents for Energic Plus RX
-
Page 1: Battery Charger
BATTERY CHARGER BATTERY CHARGER USER’S MANUAL USER’S MANUAL…
-
Page 2
(THIS PAGE WAS INTENTIONALLY LEFT BLANK) -
Page 3: Table Of Contents
TABLE OF CONTENTS Table of Contents · GENERAL………………..4 · 1. Introduction………………….. 4 · 2. Safety instructions and warnings…………..5 · RX SINGLEPHASE………………7 · 3. Description………………….7 · 4. Installation………………….8 · 5. Operation………………….11 · RX THREEPHASE………………14 ·…
-
Page 4: General
RESPONSIBILITY DISCLAIMER The manufacturer of the Energic plus RX battery charger will not be responsible for damages and/or injuries caused by the charger in these situations: The charger is not installed properly by a qualified electrician;…
-
Page 5: Safety Instructions And Warnings
Battery Charger RX User’s Manual Safety instructions and warnings GENERAL Battery chargers can cause injury or death, or damage to other equipment or property, if the user does not strictly observe all safety rules and take precautionary actions. Safe practices must be learned through study and training before using this equipment.
-
Page 6
Battery Charger RX User’s Manual BURN AND BODILY INJURY PREVENTION The battery produces very high currents when short circuited, and will burn the skin severely if in contact with any metal conductor that is carrying this current. Do not permit rings on fingers to come in contact with battery terminals or the cell connectors on top of the battery. -
Page 7: Rx Singlephase
User’s Manual RX SINGLEPHASE Description Energic plus RX battery chargers have been designed to charge Pb batteries. These units can convert the AC input voltage to a DC voltage at the correct level, in order to charge the battery cells.
-
Page 8: Installation Of The Charger
Battery Charger RX User’s Manual 4. Installation of the charger Conditions of use: Operating temperature: 5°C to 45°C • Storage temperature: -20°C to 60°C • Relative humidity: less than 75% • CAUTION The charger can be installed by qualified personnel only.
-
Page 9
Battery Charger RX User’s Manual INTERNAL VIEW OF THE CHARGER NOTE Check the efficiency of earth circuitry (yellow/green cable); Connect the charger to the mains using an adeguate plug, with pushbutton and fuses; Use an adeguate plug to connect the charger to the battery. -
Page 10
Battery Charger RX User’s Manual ELECTRICAL INSTALLATION OF THE CHARGER Check the efficiency of earth circuitry (yellow/green wire); • Connect the charger to the mains using an adeguate plugs, with pushbutton and fuses; • Use an adeguate plug to connect the charger to the battery;… -
Page 11: Operation
Battery Charger RX User’s Manual Operation PRELIMINARY CONTROLS Inspect the charger completey for loose screws, electrical connections or other damages; • Check that all the ventilation slots are not obstructed to assure proper air flow; • Make sure that the charger is installed as instructed in this manual and in accordance with •…
-
Page 12
WARNING ! ENERGIC Plus RX chargers are programmed to do a complete cycle of charge, however it’s recommended to survey the operations when the battery must remain connected to the charger for more than 12 hours (example: week-ends) -
Page 13
The EQUALIZATION function, performed by ENERGIC Plus RX chargers, has been developed to keep all the cells of the battery at the same level, even after years of continuous work. -
Page 14: Rx Threephase
User’s Manual RX THREEPHASE Description Energic plus RX battery chargers have been designed to charge Pb batteries. These units can convert the AC input voltage to a DC voltage at the correct level, in order to charge the battery cells.
-
Page 15: Installation
Battery Charger RX User’s Manual 7. Installation Conditions of use: Operating temperature: 5°C to 45°C • Storage temperature: -20°C to 60°C • Relative humidity: less than 75% • CAUTION The charger can be installed by qualified personnel only. NOTE This unit operates on threephase AC input, 380 Vac, 50Hz.
-
Page 16
Battery Charger RX User’s Manual INTERNAL VIEW OF THE CHARGER NOTE Check the efficiency of earth circuitry (yellow/green cable); Connect the charger to the mains using an adeguate plug, with pushbutton and fuses; Use an adeguate plug to connect the charger to the battery. -
Page 17
Battery Charger RX User’s Manual ELECTRICAL INSTALLATION OF THE CHARGER Check the efficiency of earth circuitry (yellow/green wire); • Connect the charger to the mains using an adeguate plugs, with pushbutton and fuses; • Use an adeguate plug to connect the charger to the battery. -
Page 18: Operation
Battery Charger RX User’s Manual 8. Operation PRELIMINARY CONTROLS Inspect the charger completey for loose screws, electrical connections or other damages; • Check that all the ventilation slots are not obstructed to assure proper air flow; • Make sure that the charger is installed as instructed in this manual and in accordance with •…
-
Page 19
1 second. This control is useful to be sure that the electronic control is working correctly. Energic Plus RX chargers are programmed to do a complete cycle of charge, however it’s recommended to survey the operations when the battery must remain connected to the charger… -
Page 20
During extra charge cycles the LEDs “ FINAL CHARGE” and “STOP-100%” flash alternately. NOTE The operations described in this chapter are done by ENERGIC Plus RX chargers automatically. END OF CHARGE When the battery is completely charged the charger is turned off and the LED “STOP – 100%”… -
Page 21: Trouble Shooting Guide
Battery Charger RX User’s Manual TROUBLE SHOOTING GUIDE SYMPTOM POSSIBLE CAUSES ACTION 1 Battery not connected properly. Check battery connectors/harness. Charger does not Charger has been connected to Disconnect forkift motor and react to battery forklift motor connector. connect battery.
-
Page 22
Battery Charger RX User’s Manual Page 22 of 25 OWM-040906-RX Version: 02-AB… -
Page 23
Battery Charger RX User’s Manual Page 23 of 25 OWM-040906-RX Version: 02-AB… -
Page 24: Spare Parts List
COMMON PARTS – SINGLEPHASE CABINET S POSITION CODE DESCRIPTION 0203340 Base RE box S 0203341 Cover RE box S 0203129T Printcard external plate RX RLCBSRE-06-01 Printcard support (x4) 0201321 Main switch 0-1 0201829 Cable strain relief 0201828 Cable strain relief…
-
Page 25
Battery Charger RX User’s Manual COMMON PARTS – THREEPHASE POSITION CODE DESCRIPTION 0203370 Base RE box B 0203374 Cover RE box B 0203125 Printcard external plate RE RLCBSRE-06-01 Printcard support (x4) 203141 Pushbutton 0-1 0203999 Varistor 275V 100001 Output fuse holder…
Зарядные устройства Energic plus RX предназначены для заряда свинцовых аккумуляторов.
Эти устройства преобразуют входное переменное напряжение в постоянное напряжение требуемого уровня для зарядки ячеек аккумуляторных батарей.
Экономичное зарядное устройство для ричтраков, штабелеров, погрузчиков. Полностью автоматическое, микропроцессорное управление.
Основные детали зарядного устройства, доступные для пользователя:
- Внешний корпус;
- Панель управления со светодиодами;
- Главный выключатель (0-1);
- No.2 Кабели для подключения аккумулятора;
- No.1 Кабель питания от сети.
Зарядное устройство RX-T-48-120
Зарядное устройство RX-T-48-120 предназначено для заряда свинцовых аккумуляторов.
Технические характеристики:
| Параметр | Значение |
| Работает полностью автоматически | Да |
| Выходное напряжение постоянного тока (В) | 48 |
| Выходной постоянный ток (А) | 120 |
| Переменное входное напряжение (В) | 380 |
| Диапазон емкости аккумулятора 10 часов (Ач) | 360-500 |
| Потребляемая мощность (кВА) | 5,6 |
| КПД зарядного устройства (%) | 90 |
| Габаритные размеры (LxBxH) мм | 500x360x700 |
| Вес зарядного устройства (кг) | 49 |
| Функция выравнивания | Да |
| Рабочая температура | от 5ºС до 45ºС |
| Температура хранения | от -20ºС до 60ºС |
| Относительная влажность | менее 75% |
Полностью автоматическое зарядное устройство аккумуляторов с микропроцессорным управлением. простая компактная конструкция.
Светодиодная панель управления:
- Аккумулятор подключен — выполняется зарядка
- Окончательная зарядка
- Зарядка завершена — выполняется выравнивание заряда
- Аварийная остановка
- Отключение тока в электросети
- Амперметр 0-100%
Зарядные устройства серии RX
| Модель ЗУ | Выходное напряжение постоянного тока (В) | Диапазон емкости аккумулятора 10 часов (Ач) | Габаритные размеры (LxBxH) мм |
| RX-T 48V 40A | 48 | 200-240 | 500x340x360 |
| RX-T 48V 50A | 48 | 200-240 | 500x340x360 |
| RX-T 48V 60A | 48 | 250-300 | 500x340x360 |
| RX-T 48V 80A | 48 | 360-500 | 500x340x360 |
| RX-T 48V 100A | 48 | 500-599 | 500x340x360 |
| RX-T 48V 120A | 48 | 490-600 | 500x340x360 |
| RX-T 48V 140A | 48 | 750-900 | 500x360x700 |
| RX-T 48V 160A | 48 | 900-1024 | 500x360x700 |
| RX-T 48V 180A | 48 | 1025-1149 | 500x360x700 |
| RX-T 48V 200A | 48 | 600-749 | 500x360x700 |
Автоматический запуск после подключения аккумулятора с 3 задержками, чтобы избежатьдугового искренения между разъемами. Автоматическое выключение после отсоединения аккумулятора во время зарядки.
Автоматическое сохранение параметров зарядки в случае отключения тока в электросети и автоматический перезапуск при возобновлении питания.
Гарантия 1 год.
COMMON PARTS – THREEPHASE
POSITION
1
2
3
4
5
6
7
8
9
VARIABLE PARTS – CABINET C
POS.
DESCR.
Rectifier
10
POS.
DESCR.
Printcard
11
POS.
DESCR.
Output fuse
12
CABINETS TABLE
Singlephase
CABINET
S
24/20
A
24/40
B
48/60
OWM-040906-RX Version: 02-AB
CODE
0203370
0203374
0203125
RLCBSRE-06-01
203141
0203999
100001
1020CA01
0203262
24-60
24-80
0202021
0202022
40-60
40-80
0202021
0202022
24-60
24-80
0202752
0202752
40-60
40-80
02027535
02027535
24-60
2480
0201065
0201066
40-60
40-80
0201065
0201066
Singlephase
Units
24/25
24/30
24/50
24/60
48/80
24-100
36-60
0202023
0202021
48-50
48-60
0202021
0202021
24-100
36-60
0202752
0202753
48-50
48-60
0202754
0202754
24-100
36-60
0201067
0201065
48-50
48-60
0201064
0201065
CABINET
B
Battery Charger RX
DESCRIPTION
Base RE box B
Cover RE box B
Printcard external plate RE
Printcard support (x4)
Pushbutton 0-1
Varistor 275V
Output fuse holder
Plastic feet RE (x4)
Contactor
36-80
36-100
0202022
0202023
48-80
48-100
0202022
0202023
36-80
36-100
0202753
0202753
48-60
48-100
0202754
0202754
36-80
36-100
0201066
0201067
48-80
48-100
0201066
0201067
Threephases
Threephase
Units
ALL MODELS
User’s Manual
40-50
0202021
72-60
0202021
40-50
02027535
72-60
0202755
40-50
0201064
72-60
0201065
Page 25 of 25
info@akbremont.ru
Отдел подбора
Стоимость и наличие уточним при оформлении заказа
Оплата
Онлайн или по счету
Описание товара
Зарядное устройство Energic Plus RX-T-T 48V 100Ah 380V. Купить недорогое зарядное устройство для тягового аккумулятора. Бренд Energic Plus — бюджетный вариант трёхфазного зарядника для классической батареи погрузчика с мощными техническими характеристиками.
Energic Plus RX-T-T 48V 100Ah 380V подойдёт для свинцово-кислотного аккумулятора с напряжением 48V и ёмкостью 500-600 Ач. Подключение в розетку 380V
Похожие товары
Технические характеристики:
| Вес | 53 kg |
|---|---|
| Габариты | 50 × 34 × 36 cm |
| Напряжение сети, V |
380В |
| Напряжение, В |
48V |
| Сила ток заряда, А |
100А |
| Бренд |
Energic Plus |
| Страна производитель |
Италия |
| Технология |
Свинцово-кислотная |
| Гарантия производителя |
24 месяца |
Похожие товары
Заполните заявку и менеджеры магазина быстро подберут нужную деталь
(Ocr-Read Summary of Contents of some pages of the Energic Plus RX Document (Main Content), UPD: 10 August 2023)
-
18, 18 USER MANUAL BATTERY CHARGER RX AC Input Fails After the end of the charge process, if the battery remains connected to the charger for more than 15 hours the MRG4- 3 Control Board executes the Equalizations cycles. The equalization cycles consist of 4 extra charge cycles of 30 minutes executed every 15 hours. During extra charge cycles the LEDs “ FINAL CHARGE” and “STOP” flash alternately. Equalization Cycle The EQUALIZATION …
-
26, 26 USER MANUAL BATTERY CHARGER RX The battery voltage reached during the charging cycle or during an equalization cycle is too high (over 2,80V/cell). The charge cycle stops. The charge current reached during the charge cycle is too high (over the 140% of the nominal value). The battery voltage hasn’t reached the gassing point within 12 hours of charge.
… -
32, [email protected] • www.energicplus.com TVH Parts NV • Brabantstraat 15 • 8790 Waregem • Belgium © February 2020. Energic Plus is a trademark of TVH Parts Holding nv, Brabantstraat 15, B-8790 Waregem. Photographs and illustrations are included for referencepurposes only. REF 47657596 • 02-2020 • JS
… -
13, Energic Plus RX 13 USER MANUAL BATTERY CHARGER RX 567SCE Control Board – CHARGE OPERATION The charge current follows the Wa charge curve as described in the DIN 41774 norm. During the first phase of charge, since the beginning of the charge cycle until the reaching of the gasing point, the led ‘CHARGE ON’ blinks. If the gassing point , equal to 2,4V/cell, isn’t reached within 12 hours since the beginning of the …
-
29, 29 USER MANUAL BATTERY CHARGER RX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . …
-
11, 11 USER MANUAL BATTERY CHARGER RX 5. Operation CHARGING CYCLES The standard model of the RX chargers follows the Wa charging curve as described in the DIN 41774 norm. Current Voltage Initial Current (about 16% of battery capacity) Voltage Current Time Voltage = 2.40 V/cell Current = 50% of initial current Voltage = 2.00 V/cell On the Wa charge curve, the relationship between the battery voltage and the output current of the charger can be described in 3 points…
-
9, 9 USER MANUAL BATTERY CHARGER RX AC VOLTAGE ADJUSTMENT – SINGLE PHASE – Box B-C • Disconnect the charger from main supply and from the battery; • Open the cabinet; • Find the terminal blocks for AC input voltage setting; • Connect the wires A and B to the desired position. [Check the table to find the correct position]; • Close the cabinet; • Connect the charger to main supply. AC VOLTAGE ADJUSTMENT – THREE PHASES – Box B-C-D-E • Disconnect the cha…
-
12, 12 USER MANUAL BATTERY CHARGER RX NOTE The operations described in these chapters are done by ENERGIC Plus RX chargers automatically. WARNING ! Before disconnecting the battery, check it is not being charged. If it is charging turn off the charger using the main switch or the stop pushbutton, to avoid sparks between connectors. RX SINGLEPHASE – BOX S-A-B The RX SINGLEPHASE Chargers made on the Box S,A,B mount the 567SCE Control Board. The Front Panel of the 567SCE Control Board is compose…
-
20, 20 USER MANUAL BATTERY CHARGER RX The battery voltage reached during the charging cycle or during an equalization cycle is too high (over 2,80V/cell). The charge cycle stops. The charge current reached during the charge cycle is too high (over the 140% of the nominal value). The battery voltage hasn’t reached the gassing point within 12 hours of charge.
… -
16, 16 USER MANUAL BATTERY CHARGER RX RX THEEPHASES – BOX B The RX THREEPHASES Chargers made on the Box B mounts the MRG4-3 Control Board. The Front Panel of the MRG4-3 Control Board is composed by 4 Status Led that indicate the state of charge and 3 Leds that indicate the charge current level. After the connection of the battery, the Control Board turns on. If the battery and the AC Input are properly connected the charger cycle sta…
-
27, 27 USER MANUAL BATTERY CHARGER RX 6. TROUBLE SHOOTING GUIDE Symptom Possible causes Action Charger does not react to battery being connected, and LED control panel remains OFF. A 1 Battery not connected properly. Check battery connectors/harness. 2 Charger has been connected to forklift motor connector. Disconnect forkift motor and connect battery. 3 Output cables reversed. Check charger, connectors and battery polarities. Output fuse is probably blown.…
-
24, 24 USER MANUAL BATTERY CHARGER RX The EQUALIZATION function, performed by ENERGIC Plus RX chargers, has been developed to keep all the cells of the battery at the same level, even after years of continuous work. After the End of 4 Equalization Cycles the Led’ STOP ‘ is fixed ON to indicate that also the equalization cycles have been succesfully completed. End of the charge process and equalization cycles MRG5-7 Control Board – ALARMS If the Led…
-
3, Energic Plus RX 3 USER MANUAL BATTERY CHARGER RX 1. Introduction This manual contains instructions and suggestions for the users of Energic plus RX battery chargers. Before to install, use or repair the charger, it’s necessary to read and understand this manual completely. It’s recommended to keep the manual in good condition for all the lifetime of the charger. It should be kept in a dry and clean place, always available to the users. Throughout this …
-
19, 19 USER MANUAL BATTERY CHARGER RX MRG4-3 Control Board – ALARMS If the Led ‘Emergency Stop’ blinks means that the charge cycle or an Equalization cycle has been interrupted because an alarm has occurred. The MRG4-3, lighting the current leds on the left, can indicate the cause of the allarm. Stop Pushbutton pressed during the charge cycle or during an equalization cycle. The battery voltage read after the connection of the battery is too…
-
21, 21 USER MANUAL BATTERY CHARGER RX RX SINGLEPHASE and THREEPHASES – BOX C(RL) – BOX D(RTC) – BOX E (MAXI) The RX Chargers made on the Box C(RL),D(RTC) and E(MAXI) mounts the MRG5-7 Control Board. The Front Panel of the MRG5-7 Control Board is composed by 5 Status Led that indicate the state of charge and 7 Leds that indicate the charge current level. After the connection of the battery, the Control Board turns on. The …
Зарядные устройства Energic plus RX предназначены для заряда свинцовых аккумуляторов.
Эти устройства преобразуют входное переменное напряжение в постоянное напряжение требуемого уровня для зарядки ячеек аккумуляторных батарей.
Экономичное зарядное устройство для ричтраков, штабелеров, погрузчиков. Полностью автоматическое, микропроцессорное управление.
Основные детали зарядного устройства, доступные для пользователя:
- Внешний корпус;
- Панель управления со светодиодами;
- Главный выключатель (0-1);
- No.2 Кабели для подключения аккумулятора;
- No.1 Кабель питания от сети.
Зарядное устройство RX-T-48-120
Зарядное устройство RX-T-48-120 предназначено для заряда свинцовых аккумуляторов.
Технические характеристики:
| Параметр | Значение |
| Работает полностью автоматически | Да |
| Выходное напряжение постоянного тока (В) | 48 |
| Выходной постоянный ток (А) | 120 |
| Переменное входное напряжение (В) | 380 |
| Диапазон емкости аккумулятора 10 часов (Ач) | 360-500 |
| Потребляемая мощность (кВА) | 5,6 |
| КПД зарядного устройства (%) | 90 |
| Габаритные размеры (LxBxH) мм | 500x360x700 |
| Вес зарядного устройства (кг) | 49 |
| Функция выравнивания | Да |
| Рабочая температура | от 5ºС до 45ºС |
| Температура хранения | от -20ºС до 60ºС |
| Относительная влажность | менее 75% |
Полностью автоматическое зарядное устройство аккумуляторов с микропроцессорным управлением. простая компактная конструкция.
Светодиодная панель управления:
- Аккумулятор подключен — выполняется зарядка
- Окончательная зарядка
- Зарядка завершена — выполняется выравнивание заряда
- Аварийная остановка
- Отключение тока в электросети
- Амперметр 0-100%
Зарядные устройства серии RX
| Модель ЗУ | Выходное напряжение постоянного тока (В) | Диапазон емкости аккумулятора 10 часов (Ач) | Габаритные размеры (LxBxH) мм |
| RX-T 48V 40A | 48 | 200-240 | 500x340x360 |
| RX-T 48V 50A | 48 | 200-240 | 500x340x360 |
| RX-T 48V 60A | 48 | 250-300 | 500x340x360 |
| RX-T 48V 80A | 48 | 360-500 | 500x340x360 |
| RX-T 48V 100A | 48 | 500-599 | 500x340x360 |
| RX-T 48V 120A | 48 | 490-600 | 500x340x360 |
| RX-T 48V 140A | 48 | 750-900 | 500x360x700 |
| RX-T 48V 160A | 48 | 900-1024 | 500x360x700 |
| RX-T 48V 180A | 48 | 1025-1149 | 500x360x700 |
| RX-T 48V 200A | 48 | 600-749 | 500x360x700 |
Автоматический запуск после подключения аккумулятора с 3 задержками, чтобы избежатьдугового искренения между разъемами. Автоматическое выключение после отсоединения аккумулятора во время зарядки.
Автоматическое сохранение параметров зарядки в случае отключения тока в электросети и автоматический перезапуск при возобновлении питания.
Гарантия 1 год.