Эхолот lucky fl218tpa инструкция по применению на русском языке

—6—

6. FIXING SONAR SENSOR6.1 Pull out the rubber stopper, adjust float so that it is18 to 22 cm from the sensor, or at your desired depth.Replace the rubber stopper by pressing it firmly into the float. The Sensor float must be adjusted so that it is a minimum of 18 cm away from the sensor.6.2 Toss the sonar sensor and float assembly into water at your desired fishing location.To toss, place the sonar sensor and float in your hand, and pitch underhand. Do not throw the sensor by the cable as this will cause unrepairable damage. Before tossing, be certain that the cable is free from tangles and is not wrapped around anything.6.3 Your fish finder includes a combination adapter, mounting bracket for the sonar sensor.The Adapter includes mounting taps so that you can attach it to any flat surface or boat hull and appropriate rod, The Adapter is removable and adjustable up to 180 Degrees.

6.4 Use a pole to guide the sonar sensor to a desirable position or

add floats on the cable to float on the water.

—7—

NOTE:*Incorrect to use : Do not allow the cable to sink to the

bottom as it may become entangled in debris.

* The float can be removed as follows, If you do not need it,

cutting off the rubber stopper from the cable and sliding the

safety strap and the float towards the plug and gently take it out

from the plug.

7 FISHING AT THE BOAT OR ICE

7.1 FISHING AT THE BOAT

7.1.1 Toss the sensor and float into the water as per the previous instructions.

7.1.2 Attach the adapter to the boat hull using the mounting tabs.

7.1.3 “shoot –Thru” the hull of a boat.

Place the sonar sensor in 1 inches of water against the hull bottom.

Or coat the face of the sonar sensor with petroleum jelly and press it

against the hull bottom with a twisting motion.

7.1.3if it still doesn’t work on all hulls and you may have to place the

sensor directly in the water for proper operation.

NOTE: If depth readings appear as «—» while using one of these

methods, place the sonar sensor directly in the water to verity

that the fish finder is operating properly. If it operates properly

while directly in the water, reposition the sensor in a new location

in the hull, and repeat the methods in above

—8—

7.2 FISHING ON ICE

To achieve the best performance for ice fishing, it is highly recommended

that you cut a hole through the ice and place the sonar sensor directly

in the water.If you would like to check the area for depth or fish before

cutting the hole. Clear away snow to expose the ice surface, making

sure the surface is smooth. Place a small amount of liquid water on the

ice and set the sonar sensor on the water, allowing the unit to freeze

to the ice (fig. 22 ).

If there are any air pockets between the sonar senor and ice, or air

on the water below the ice, the unit will not work properly and will

require you to try another spot, or cut a hole in the ice to use.

NOTE:* To remove the sonar sensor from the frozen gently tap

sonar sensor at the base with your hand. If it will not come loose,

spray a small amount of water on the ice surface around the base

and repeat above step until the sonar sensor is easily removed.

Never use a blunt to strike the sonar sensor as this may cause

damage to the sensitive internal electronics.

* Cold weather is extremely hard on the electrical components

within the display housing. It is suggested that you keep the

unit in temperatures above -17 degrees Celsius during operation.

*Remove the batteries from the fish finder to prevent battery

leakage and corrosion.Clean the sonar sensor and cable with

fresh water and dry-off before storing .Do not submerge and/or

spray the fish finder screen/housing with water or use chemicals

to clean.

—9—

8 Product specification

Display: 2.2inch LCD

Depth Capability: 328feet(100m)

Sonar Coverage: 45 degrees beam angle in 200Khz

Power Requirement: 4xAAA alkaline batteries

Waterproof design: level-4 (spray-water-proof)

Show large and small fish, water depth, water temperature, air

temperature, air pressure, fish location, and bottom grass & rock

User selectable sensitivity, depth units, and fish alarm setting

Built in memory stores sonar setting when the fish finder is turned off

Operational Temperature: 14°F to 122°F(-10°C to 50°C)

9 Attachments:

1)Round Transducer with 8m Cable

2)Transducer Adapter

3)Bracket

4)Stand

—1—

PORTABLE FISH FINDER

OPERATION GUIDE

We are really appreciated that you purchase our products! In order to make the users give the machinery performance into full play and well utilize this machine, we are pleased to ask the users to read the operating instruction carefully before operating the machine. If you have any question in use, please feel free to contact the Zhejiang lucky Manufacturer Co.,Ltd for consultation: WWW.LUCKYSONAR.COM

Sonar technology is based on sound waves.

The system uses sonar to locate and define

structure, bottom contour and composition,

as well depth directly below the transducer.

The transducer sends a sound wave signal

and determines distance by measuring the

time between the transmission of the sound

wave and when the sound wave is reflected

off an object; it then uses the reflected signal

to interpret location, size, and composition of

an object.

This amazing product is especially

designed for amateur and professional

fishermen alike, to findout the location

of fish and depth of water.The unit can

be used in ocean, river or lake and is

fantastic for datecting schools of fish in

any particular area.

Using amazing and innovative technology, this portable fishfinder is

the ideal toolto bring the fish toyou!

2 HOW SONAR WORKS

1 PRODUCT OVERVIEW

—2—

3 DISPLAY VIEW

4 OPERATION AND SETTING

4.1 POWER ON/OFF

Slide and remove the Battery Door, lnstall 4 AAA batteries. Be certain to align the batteries as per the diagram within the battery compartment.Close the battery door completely.

1.water depth

2.air temperature

3.Mode Menu

4.General Mode

5.Shallow Mode

6.Slope Mode

7.Small fish

8.Sensitivity.

9.Water temperature.

10.Air pressure

11.Battery strength

12.Fish alarm on/off

13.Ice fishing Mode

14.Raft Mode

15.Large fish

16.Fish depth indicator

1.Mode menu 2.Left menu 3.Setup menu

4.Right menu 5.Power ON/OFF

1

3

4

5

6

8

7

9 11

12

13

14

15

2

10

1

2

3

4

—3—

Press the POWER key to turn the power On , the unit enter normal mode

after display full show 1 second. Press and Hold the POWER key for 3

seconds to turn the Power Off. To enter the simulation mode: press and

hold the POWER key for 5 seconds and release while the power is off.

NOTE: The unit must be turned off to enter normal operation

from simulation mode.

Automatic power off feature : The display will shut off

automatically when the depth display reads «—» continuously

for 5 minutes.

4.2 FUNCTION SETTING

Press and Hold the SETUP key for 3 seconds, Water depth unit

{ FT } will blink; then pressing the SETUP key again and again, the

indicator will blink from the current feature to be set.

Water depth unit { FT } — Sensitivity{ } —Water temperature unit

—Air temperature unit— Alarm{ }.

Press the POWER key to turn the power On , the unit enter normal mode after display full show 1 second.Press Mode menu to select mode among General mode, Shallow mode, Slope mode, Raft mode, and Ice-fishing mode. NOTE: The screen can be refreshed by pressing the POWER key during normal operation.

—4—

15.8

M

M

If the finder determines that sonar has detected a fish,the display will show a fish shaped icon. It can detect large fish and small fish.The first column of fish indicators on the right of the display shows the most current information. This column is then moved to the left as a new reading is displayed Fish icon moved in every 5 seconds.5.2 FISH SHOW

5 FISH AND DEPTH READOUT

5.1 READINIG DEPTHThe depth readout on the top right, will appear after the power is turned ON and the sonar sensor is placed in water. The depth meter will indicate”—” if the depth exceeds these parameters. (0 .7 to 100 meters)NOTE: This reading may also occur in water is extremely dirty, or where there are heavy silt or mud bottoms. Sonar is a sound signal that travels through water. Sonar will not travel through air. Keep this in mind when using the fish finder, as the smallest bubble between the sonar sensor and the water, will cause the unit not to operate correctly.NOTE: The fish indicators move away from the right to the left at a constant speed. This motion in no way reflects actual movement of the fish.small fishlarge fish

—5—

a

b c

d

e

f

Use the fish Depth lndicator tomeasure the fish’s depth from the sonar sensor.This can be

done by dividing the depth

reading by 10. This number represents the value of each

box.

(Example, the depth is 20 m, the fish symbol appears in the 5th box from the top. This means the fish is 10 m from the surface)5.3 WEED SHOW5.4 BOTTOM CONTOURThe display indicates the presence of short weeds by turning on the smallest Weed indicator (a) Moderately tall weeds are depicted by turning on the second Weed indicators(b) Tall weeds are depicted by turning on the third Weed indicator(c)One Rock lndicator identifies limited structure(d) You would most likely find a small rock, a small pile of rocks, or uneven bottom contour. This is not a bad place for hiding fish, but due to the limited amount of strucrure, there may not be a lot.Two Rock lndicators identifies a considerable amount of bottom structure, but scattered(e) A considerable amount of time needs to be spent fishing this area as each piece of structure could be hiding a prize catch.Three Rock lndicators indicates a large amount of bottom structure in a confined area. This bottom may consist of a large rock(s), stump(s), tree(s), or a ledge(s)(f)

PORTABLE FISH FINDER

OPERATION GUIDE

На чтение 8 мин Просмотров 5.1к.

—6—

6. FIXING SONAR SENSOR6.1 Pull out the rubber stopper, adjust float so that it is18 to 22 cm from the sensor, or at your desired depth.Replace the rubber stopper by pressing it firmly into the float. The Sensor float must be adjusted so that it is a minimum of 18 cm away from the sensor.6.2 Toss the sonar sensor and float assembly into water at your desired fishing location.To toss, place the sonar sensor and float in your hand, and pitch underhand. Do not throw the sensor by the cable as this will cause unrepairable damage. Before tossing, be certain that the cable is free from tangles and is not wrapped around anything.6.3 Your fish finder includes a combination adapter, mounting bracket for the sonar sensor.The Adapter includes mounting taps so that you can attach it to any flat surface or boat hull and appropriate rod, The Adapter is removable and adjustable up to 180 Degrees.

6.4 Use a pole to guide the sonar sensor to a desirable position or

add floats on the cable to float on the water.

—7—

NOTE:*Incorrect to use : Do not allow the cable to sink to the

bottom as it may become entangled in debris.

* The float can be removed as follows, If you do not need it,

cutting off the rubber stopper from the cable and sliding the

safety strap and the float towards the plug and gently take it out

from the plug.

7 FISHING AT THE BOAT OR ICE

7.1 FISHING AT THE BOAT

7.1.1 Toss the sensor and float into the water as per the previous instructions.

7.1.2 Attach the adapter to the boat hull using the mounting tabs.

7.1.3 “shoot –Thru” the hull of a boat.

Place the sonar sensor in 1 inches of water against the hull bottom.

Or coat the face of the sonar sensor with petroleum jelly and press it

against the hull bottom with a twisting motion.

7.1.3if it still doesn’t work on all hulls and you may have to place the

sensor directly in the water for proper operation.

NOTE: If depth readings appear as «—» while using one of these

methods, place the sonar sensor directly in the water to verity

that the fish finder is operating properly. If it operates properly

while directly in the water, reposition the sensor in a new location

in the hull, and repeat the methods in above

—8—

7.2 FISHING ON ICE

To achieve the best performance for ice fishing, it is highly recommended

that you cut a hole through the ice and place the sonar sensor directly

in the water.If you would like to check the area for depth or fish before

cutting the hole. Clear away snow to expose the ice surface, making

sure the surface is smooth. Place a small amount of liquid water on the

ice and set the sonar sensor on the water, allowing the unit to freeze

to the ice (fig. 22 ).

If there are any air pockets between the sonar senor and ice, or air

on the water below the ice, the unit will not work properly and will

require you to try another spot, or cut a hole in the ice to use.

NOTE:* To remove the sonar sensor from the frozen gently tap

sonar sensor at the base with your hand. If it will not come loose,

spray a small amount of water on the ice surface around the base

and repeat above step until the sonar sensor is easily removed.

Never use a blunt to strike the sonar sensor as this may cause

damage to the sensitive internal electronics.

* Cold weather is extremely hard on the electrical components

within the display housing. It is suggested that you keep the

unit in temperatures above -17 degrees Celsius during operation.

*Remove the batteries from the fish finder to prevent battery

leakage and corrosion.Clean the sonar sensor and cable with

fresh water and dry-off before storing .Do not submerge and/or

spray the fish finder screen/housing with water or use chemicals

to clean.

—9—

8 Product specification

Display: 2.2inch LCD

Depth Capability: 328feet(100m)

Sonar Coverage: 45 degrees beam angle in 200Khz

Power Requirement: 4xAAA alkaline batteries

Waterproof design: level-4 (spray-water-proof)

Show large and small fish, water depth, water temperature, air

temperature, air pressure, fish location, and bottom grass & rock

User selectable sensitivity, depth units, and fish alarm setting

Built in memory stores sonar setting when the fish finder is turned off

Operational Temperature: 14°F to 122°F(-10°C to 50°C)

9 Attachments:

1)Round Transducer with 8m Cable

2)Transducer Adapter

3)Bracket

4)Stand

—1—

PORTABLE FISH FINDER

OPERATION GUIDE

We are really appreciated that you purchase our products! In order to make the users give the machinery performance into full play and well utilize this machine, we are pleased to ask the users to read the operating instruction carefully before operating the machine. If you have any question in use, please feel free to contact the Zhejiang lucky Manufacturer Co.,Ltd for consultation: WWW.LUCKYSONAR.COM

Sonar technology is based on sound waves.

The system uses sonar to locate and define

structure, bottom contour and composition,

as well depth directly below the transducer.

The transducer sends a sound wave signal

and determines distance by measuring the

time between the transmission of the sound

wave and when the sound wave is reflected

off an object; it then uses the reflected signal

to interpret location, size, and composition of

an object.

This amazing product is especially

designed for amateur and professional

fishermen alike, to findout the location

of fish and depth of water.The unit can

be used in ocean, river or lake and is

fantastic for datecting schools of fish in

any particular area.

Using amazing and innovative technology, this portable fishfinder is

the ideal toolto bring the fish toyou!

2 HOW SONAR WORKS

1 PRODUCT OVERVIEW

—2—

3 DISPLAY VIEW

4 OPERATION AND SETTING

4.1 POWER ON/OFF

Slide and remove the Battery Door, lnstall 4 AAA batteries. Be certain to align the batteries as per the diagram within the battery compartment.Close the battery door completely.

1.water depth

2.air temperature

3.Mode Menu

4.General Mode

5.Shallow Mode

6.Slope Mode

7.Small fish

8.Sensitivity.

9.Water temperature.

10.Air pressure

11.Battery strength

12.Fish alarm on/off

13.Ice fishing Mode

14.Raft Mode

15.Large fish

16.Fish depth indicator

1.Mode menu 2.Left menu 3.Setup menu

4.Right menu 5.Power ON/OFF

1

3

4

5

6

8

7

9 11

12

13

14

15

2

10

1

2

3

4

—3—

Press the POWER key to turn the power On , the unit enter normal mode

after display full show 1 second. Press and Hold the POWER key for 3

seconds to turn the Power Off. To enter the simulation mode: press and

hold the POWER key for 5 seconds and release while the power is off.

NOTE: The unit must be turned off to enter normal operation

from simulation mode.

Automatic power off feature : The display will shut off

automatically when the depth display reads «—» continuously

for 5 minutes.

4.2 FUNCTION SETTING

Press and Hold the SETUP key for 3 seconds, Water depth unit

{ FT } will blink; then pressing the SETUP key again and again, the

indicator will blink from the current feature to be set.

Water depth unit { FT } — Sensitivity{ } —Water temperature unit

—Air temperature unit— Alarm{ }.

Press the POWER key to turn the power On , the unit enter normal mode after display full show 1 second.Press Mode menu to select mode among General mode, Shallow mode, Slope mode, Raft mode, and Ice-fishing mode. NOTE: The screen can be refreshed by pressing the POWER key during normal operation.

—4—

15.8

M

M

If the finder determines that sonar has detected a fish,the display will show a fish shaped icon. It can detect large fish and small fish.The first column of fish indicators on the right of the display shows the most current information. This column is then moved to the left as a new reading is displayed Fish icon moved in every 5 seconds.5.2 FISH SHOW

5 FISH AND DEPTH READOUT

5.1 READINIG DEPTHThe depth readout on the top right, will appear after the power is turned ON and the sonar sensor is placed in water. The depth meter will indicate”—” if the depth exceeds these parameters. (0 .7 to 100 meters)NOTE: This reading may also occur in water is extremely dirty, or where there are heavy silt or mud bottoms. Sonar is a sound signal that travels through water. Sonar will not travel through air. Keep this in mind when using the fish finder, as the smallest bubble between the sonar sensor and the water, will cause the unit not to operate correctly.NOTE: The fish indicators move away from the right to the left at a constant speed. This motion in no way reflects actual movement of the fish.small fishlarge fish

—5—

a

b c

d

e

f

Use the fish Depth lndicator tomeasure the fish’s depth from the sonar sensor.This can be

done by dividing the depth

reading by 10. This number represents the value of each

box.

(Example, the depth is 20 m, the fish symbol appears in the 5th box from the top. This means the fish is 10 m from the surface)5.3 WEED SHOW5.4 BOTTOM CONTOURThe display indicates the presence of short weeds by turning on the smallest Weed indicator (a) Moderately tall weeds are depicted by turning on the second Weed indicators(b) Tall weeds are depicted by turning on the third Weed indicator(c)One Rock lndicator identifies limited structure(d) You would most likely find a small rock, a small pile of rocks, or uneven bottom contour. This is not a bad place for hiding fish, but due to the limited amount of strucrure, there may not be a lot.Two Rock lndicators identifies a considerable amount of bottom structure, but scattered(e) A considerable amount of time needs to be spent fishing this area as each piece of structure could be hiding a prize catch.Three Rock lndicators indicates a large amount of bottom structure in a confined area. This bottom may consist of a large rock(s), stump(s), tree(s), or a ledge(s)(f)

PORTABLE FISH FINDER

OPERATION GUIDE

Смотреть руководство для Lucky FL218TPA-WT ниже. Все руководства на ManualsCat.com могут просматриваться абсолютно бесплатно. Нажав кнопку «Выбор языка» вы можете изменить язык руководства, которое хотите просмотреть.

Бренд:

Lucky

Продукт:

эхолоты

Модель/название:

FL218TPA-WT

Тип файла:

PDF

Доступные языки:

английский

Сопутствующие товары Lucky FL218TPA-WT