Cubase 5 инструкция на русском скачать pdf

8

9

EN

EN

•  Unpack the coffee maker and remove all the packaging 

materials. 

•  Keep the original package.

•  Check the delivery set.

•  Read the safety measures and operating 

recommendations.

•  Examine the coffee maker for damages, in case of 

damage do not plug it into the mains.

•  Make sure that the specifications of power supply 

voltage specified on the lower panel of the unit 

correspond to the specifications of your mains. When 

the unit is used in the mains with 60 Hz frequency, it 

does not need any additional settings.

•  Wipe the surface of the coffee maker body with a clean, 

slightly damp cloth to remove dust. 

•  Before using the coffee maker for the first time, wash all 

removable parts (1, 2, 9, 10, 14, 16, 18, 19, 20, 21) with 
warm water and neutral detergent and dry them.

BEFORE USING THE UNIT 
ATTENTION! 
If you switch the coffee maker on and don’t perform 

any actions, the coffee maker will switch off in 15 

minutes. To switch the coffee maker on press any 

button (5, 7, 8). 
•  Place the coffee maker on a steady flat heat-resistant 

surface, the distance from the side walls of the coffee 

maker should be at least 20 cm, and the gap above the 

coffee maker should be at least 30 cm. 

•  Do not use the coffee maker under kitchen shelves of 

cupboards. They can be damaged by the steam released 

during the coffee maker operation. 

•  The coffee maker should be placed out of reach of small 

children.

Attention! Before making coffee for the first time it is 

recommended to wash the broiler, the cappuccinator lid (14) 

and the milk container (16). 
•  Make sure that the removable tray (1) and the tray grid 

(2) are installed to their places. 

•  Remove the lid (9), remove the water tank (10). 

•  Fill the tank (10) with cold water up to the maximal level 

mark, install the tank (10) back to its place. 

Note: the tank (10) is intended for water only, do not fill the 

tank (10) with other liquids, such as milk. 
•  Take the container (16), pull it towards yourself and 

remove it, remove the cappuccinator lid (14) from the 

container (16) (pic. 1). Fill the container with water up to 

the maximal level mark. 

Note: the cappuccinator container (16) is intended for milk 

only, do not fill the container (16) with other liquids, use 

water only in the cappuccinator lid (14) washing mode. 
•  Install the cappuccinator lid (14) on the container (16) 

and install the cappuccinator back to its place until the 

lock clicking. 

Note: after installing the container (16) with the lid (14) back 

to its place always check if it is installed and fixed properly. 

•  Set the milk supply intensity control knob (15) to the 

middle position. 

•  Install one of the coffee filters (19 or 20) into the filter 

holder (18) matching the ledge on the filter (19 or 20) 

with the hole on the holder (18) and turn the filter (19 or 

20) counter/clockwise. Do not add ground coffee into 

the filter (19 or 20) when preparing the coffee maker 

for work. 

•  Install the filter holder (18) into the installation place  « 

 » and turn the handle (4) to the right as far as it will 

go «   » (pic. 2, 3, 4). 

•  Place a cup of suitable height and capacity of at least 

300 ml on the tray grid (2). 

•  Direct the cappuccinator pipe (13) into the cup using 

the cappuccinator pipe angle adjustment bar (12). 

•  Insert the power plug into the mains socket. 

•  Switch the coffee maker on by setting the power switch 

(11) «0/I» to the position «I», the indicator (6) will light 

up and start flashing. 

•  When the coffee maker is ready for operation, the light 

indicator (6) will glow constantly. 

•  To switch the cleaning mode on press the 

«Cappuccino»-button (7) twice. 

•  After you finish cleaning the coffee maker, switch the 

coffee maker off by setting the switch (11) «0/I» to the 

position «0». 

•  Pour the water out of the cup, take the container (16), 

pull it towards yourself and remove (pic. 1), remove the 

cappuccinator lid (14) from the container (16), pour the 

remaining water from the container (16). Slightly lift the 

front part of the tray (1) and remove it, pour the water 

out of it and install the tray (1) back to its place. 

•  Turn the filter holder handle (4) to the left and remove it 

(pic. 2, 3, 4). Wait until the filter holder (18) cools down 

completely and remove the installed filter (19 or 20) 

turning it counter/clockwise. Wash the filter (19 or 20) 

and install it into the filter holder (18). 

•  If necessary, clean the boiler and the cappuccinator lid 

(14) several times. 

•  After cleaning the coffee maker is ready for operation. 
CHOOSING THE APPROPRIATE CUP
•  Before making coffee, please, select a cup of 

appropriate capacity according to the table:

Drink

Estimated amount of the ready 

drink

Espresso:   оne / 

double 

60 ml/119 ml

Cappuccino:    оne / 

double

178 ml/355 ml

Latte:    one /  double

296 ml/474 ml

RULES OF MAKING ESPRESSO
•  Use fresh-ground coffee beans or ground coffee for 

«espresso» coffee makers.

•  Make even and slightly tamp the ground coffee in the 

filter (19 or 20), you can do it with the back side of the 

measuring spoon (21) (pic. 5, 6, 7).